Top Sellers
Calibrated Resin Pump Set from MAS EPOXY
For use with 1 quart, 1/2 gallon, 1 gallon, 4 gallon and 5 gallon size containers.
|
Brightside Pre-Kote Primer - Gray, Quart from INTERLUX
Fills minor blemishes and sands easilyOne part primer for use with Brightside or any other one-part topside enamel. Microspheres provide high build and improved sandability. (Replaces Brightside Primer and 279 White Undercoater. ) Application: Brush, roller, airless/conventional spray . Number of Coats Recommended: One or two, depending on surface condition. Drying: Overcoating: 6 to 12 hrs. Drying Time: To touch: 1 to 3 hrs. Coverage: Brush: 112 sq. ft/qt, 450 sq. ft/gal; Spray: 87 sq.
|
Cetol Marine Light - Quart from INTERLUX
Enhances and protects the natural beauty of interior and exterior woodSemi-transparent finish prevents weathering and repels water. just wash wood thoroughly and apply. Three coats are recommended for the first application, followed by annual touchups. Marine Light is more translucent than Marine. If a gloss finish is desired, either may be overcoated with Marine Gloss. Quart. Long-lasting adhesion and protection from UV rays and weathering. Flexible, breathable, translucent finish; Quarts.
|
Micron CSC Antifouling Paint, Red, Quart from INTERLUX
Haul and relaunch without loss of performance The innovative copper-copolymer formula of Micron CSC provides a controlled release of antifouling biocide at the paint surface, which means that the longevity of the coating is related to the amount of paint applied. Can be applied over most paints in good condition. Micron CSC will not lose its effectiveness when hauled out of the water for extended periods of time (such as winter storage). Type: Copolymer . 2% Cuprous Oxide . Additives: None .
|
Chris Craft Stain #573 - Pint from INTERLUX
Chris Craft Stain - Pint Fills grain while staining wood, reducing the number of coats of varnish needed. May also be used on bare mahogany planking before applying primer or sanding surfacer.
|
VC-Offshore - Baltoplate Gray, Gallon from INTERLUX
Used by performance boatsVC Offshore combines superior antifouling performance with a super smooth low friction surface for the performance conscious boater. This high-strength, vinyl antifouling paint, fortified with Teflon® yields a hard, very smooth finish for maximum durability, reduced friction and increased performance. High copper loading fights fouling on performance boats in saltwater. Can be used in fresh, salt and brackish waters. Should not be applied over non-vinyl bottom paints.
|
Hullgard Primer Converter, Qt. from AWLGRIP
Hullgard Epoxy Primer is a holding primer that combines excellent anticorrosion and water barrier properties with anti-fouling tie-coat functionality. Suitable for below the waterline only, it offers a long overcoating interval without sanding to reduce work time along with superb adhesion to properly prepared fiberglass, steel, aluminum and wood. Can be recoated as soon as the solvents evaporate, even at low temperatures. 1 Gal. Theoretical Coverage – 140 Sq. 5 mils/135 microns DFT or 360 Sq.
|
|
|
Adaptor Fitting for Suzuki & Honda Lower Units from WEST MARINE
Metal threaded fitting fits MerCruiser, OMC, Evinrude, Johnson, Honda (70-90hp), Volvo, Force and Gamefisher lower units Fits standard quart plastic bottles. Flexible hose gets to hard-to-reach fill plugs.
|
Fiberglass Cleaner and Wax - Quart from SEAPOWER MARINE PROD
Cleans and waxes in one easy stepCleans, waxes, seals and protects the fiberglass surface. Contains the finest Carnauba waxes and silicones and removes surface oxidation, residue, dock marks, grease and dirt while leaving behind a durable high-gloss finish. Excellent for hand or machine use. Quart.
|
Nauta 9 Gallon Flexible Fuel Tank from IMTRA CORPORATION
Flexible gasoline tanks won't rust, don't rattle, are easy to tie down, easy to carry, and won't scrape your boat. The Nauta 9-Gallon flexible fuel tank features comfortable, molded carrying handles and rugged 840-denier nylon construction. Fitted with a 1 1/2'' pivoting fill and a capped and 1/4'' NPT hose barb. Measures 28 1/2'' x 17 1/2'' x 6 1/2''.
|
Orpine Boat Soap, Quart from ORPIN
Fresh pine scent!Replaces musty mildew odors with a pleasant fresh pine scent. Just one ounce in three gallons of fresh or saltwater will clean a 45'L boat. Biodegradable. Biodegradable.
|
Teak Care - Brightener, Quart from STARBRITE
Clean, brighten and protect your teak in three easy stepsBeautiful teak in three easy steps! Kit contains three pint-sized bottles, one each of Cleaner to remove stains and weathering; Brightener to highlight the natural grain and enhance color; and Oil to seal and protect wood from weather and UV damage. Individual, quart-sized bottles are also available. Cleaner chemically roots out stains, including ugly black mildew stains. Brightener restores teak's lustrous hue.
|
Zinc Chromate Yellow Spray Primer from MOELLER
For use on aluminum and galvanized steel surfaces above or below the waterline, this primer chemically etches into aluminum and forms a corrosion-resistant surface. Helps to create an even, bondable surface for top coat adhesion. Select color (Green or Yellow) that contrasts the least with the top coat you plan to apply. 12oz.
|
Fiberglass Boat Cleaner 920 1/2 Gallon from COLLINITE
Removes rust, exhaust, oil, grease, and oxidation stains from fiberglass. Restores the original color quickly without hard rubbing or buffing, leaves a chemically clean surface to which waxes can bond. Use with fiberglass boat wax or heavy-duty paste Fleetwax . Made in U. S. A.
|
|
Quart from INTERLUX, Gallon from INTERLUX, Primer from INTERLUX
|
|
Home -> Sailboat -> Sailboat Canvas->Inflatable Race Mark
On Your Marks, Get Set, Go! Fortunately, poorly marked regattas are a thing of the past. Our new private labeled inflatable tetrahedron racing markers are perfect for sailing clubs and junior programs. The highly visible pyramid shape assures stability, and being manufactured of durable PVC ensures durability. These markers inflate easily using an inflator pump (we recommend WM #5374111 or WM #5331475) or shop vac. Use the new West Marine inflatable racing markers. You’ll be glad you did. .
Part No: YIRM
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Interdeck® Non-Skid Paint
Provides excellent slip resistance in a variety of colorsInterdeck provides an excellent slip-resistant finish with a tough polyurethane resin that protects decks against everyday wear and tear. Interdeck has a low-sheen finish to reduce sun glare. Available in White, Cream, Beige, Gray and Blue. Formulation: One-part polyurethane nonskid enamel . Application: Brush or roller . Number of Coats Recommended: One or two . Drying Time: At 73°F - To touch: 4 hrs. to 2 days; To walk on: 2 days .
Part No: YJB000/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Interdeck® Non-Skid Paint
Provides excellent slip resistance in a variety of colorsInterdeck provides an excellent slip-resistant finish with a tough polyurethane resin that protects decks against everyday wear and tear. Interdeck has a low-sheen finish to reduce sun glare. Available in White, Cream, Beige, Gray and Blue. Formulation: One-part polyurethane nonskid enamel . Application: Brush or roller . Number of Coats Recommended: One or two . Drying Time: At 73°F - To touch: 4 hrs. to 2 days; To walk on: 2 days .
Part No: YJB923/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Interdeck® Non-Skid Paint
Provides excellent slip resistance in a variety of colorsInterdeck provides an excellent slip-resistant finish with a tough polyurethane resin that protects decks against everyday wear and tear. Interdeck has a low-sheen finish to reduce sun glare. Available in White, Cream, Beige, Gray and Blue. Formulation: One-part polyurethane nonskid enamel . Application: Brush or roller . Number of Coats Recommended: One or two . Drying Time: At 73°F - To touch: 4 hrs. to 2 days; To walk on: 2 days .
Part No: YJC089/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Primers, Undercoats & Non-Skid->Interdeck® Non-Skid Paint
Provides excellent slip resistance in a variety of colorsInterdeck provides an excellent slip-resistant finish with a tough polyurethane resin that protects decks against everyday wear and tear. Interdeck has a low-sheen finish to reduce sun glare. Available in White, Cream, Beige, Gray and Blue. Formulation: One-part polyurethane nonskid enamel . Application: Brush or roller . Number of Coats Recommended: One or two . Drying Time: At 73°F - To touch: 4 hrs. to 2 days; To walk on: 2 days .
Part No: YJF684/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Interdeck® Non-Skid Paint
Provides excellent slip resistance in a variety of colorsInterdeck provides an excellent slip-resistant finish with a tough polyurethane resin that protects decks against everyday wear and tear. Interdeck has a low-sheen finish to reduce sun glare. Available in White, Cream, Beige, Gray and Blue. Formulation: One-part polyurethane nonskid enamel . Application: Brush or roller . Number of Coats Recommended: One or two . Drying Time: At 73°F - To touch: 4 hrs. to 2 days; To walk on: 2 days .
Part No: YJG090/QT
|
|
|
|
Home -> Interior, Flags & Gifts -> Gifts
Good quality key float, bright yellow coated foam with stainless steel ball chain keeper.
Part No: YKF
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Teak Cleaners
Premium Teak Restorer cleans and brightens teak in one step, revealing its natural color and the beauty of its grain. Will not harm varnish, paintwork or aluminum 16.
Part No: YMA015/500
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Oils & Sealers->Premium Teak Oil
Penetrates and protects your teakA special blend of linseed and tung oils. Penetrates even moist wood to create an attractive sheen and easy-to-clean protective finish. Reduces mildew build-up. For all interior and exterior hardwoods. 16. 9oz. Penetrates even moist wood. Special blend of linseed and tung oils. Reduces mildew build up. For all interior and exterior hardwoods. 16.
Part No: YMA016/1L
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Bilgekote Gray Enamel
Helps to protect gelcoat and fiberglass in bilgeBilgekote is a fast-drying, durable coating formulated for application to bilge areas. Bilgekote helps prevent absorption of oil, gasoline or sludge into wood and fiberglass. Formulation: One-part enamel for bilge areas . Application: Brush, roller, conventional/airless spray. Number of Coats Recommended: One/Two. Coverage: Brush: 75 sq. ft/qt, 300 sq. ft/gal; Spray: 60 sq. ft/gal. Thinner: Brush: 333 - Model 117598; Spray: 216 - Model 117945.
Part No: YMA100/1
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Primers, Undercoats & Non-Skid->Bilgekote Gray Enamel
Helps to protect gelcoat and fiberglass in bilgeBilgekote is a fast-drying, durable coating formulated for application to bilge areas. Bilgekote helps prevent absorption of oil, gasoline or sludge into wood and fiberglass. Formulation: One-part enamel for bilge areas . Application: Brush, roller, conventional/airless spray. Number of Coats Recommended: One/Two. Coverage: Brush: 75 sq. ft/qt, 300 sq. ft/gal; Spray: 60 sq. ft/gal. Thinner: Brush: 333 - Model 117598; Spray: 216 - Model 117945.
Part No: YMA100/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Bilgekote Gray Enamel
Helps to protect gelcoat and fiberglass in bilgeBilgekote is a fast-drying, durable coating formulated for application to bilge areas. Bilgekote helps prevent absorption of oil, gasoline or sludge into wood and fiberglass. Formulation: One-part enamel for bilge areas . Application: Brush, roller, conventional/airless spray. Number of Coats Recommended: One/Two. Coverage: Brush: 75 sq. ft/qt, 300 sq. ft/gal; Spray: 60 sq. ft/gal. Thinner: Brush: 333 - Model 117598; Spray: 216 - Model 117945.
Part No: YMA102/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Thinners & Solvents->Fiberglass Surface Prep
Specifically formulated for removing mold release and wax Fiberglass-Surface Prep is your first step in removing mold release agents and wax. It thoroughly cleans your gel coat and prepares the surface for sanding and painting.
Part No: YMA601/1
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Thinners & Solvents->Fiberglass Surface Prep
Specifically formulated for removing mold release and wax Fiberglass-Surface Prep is your first step in removing mold release agents and wax. It thoroughly cleans your gel coat and prepares the surface for sanding and painting.
Part No: YMA601/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Topside Paint
A flattening agent specifically formulated for mixing with Interlux's one-part finishes, Toplac, Brightside, Yacht Enamels and varnishes (Original, Goldspar Clear and Schooner) to produce a variety of gloss, satin or matte effect finishes. For interior and exterior use.
Part No: YMA715/QT
|
|
|
|
Home -> Plumbing -> Fittings & Valves
Tapered rims prevent leaks and unpleasant odors from escaping. Made of durable, corrosion-proof plastic.
Part No: YP6114
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Primers, Undercoats & Non-Skid
Speeds up the prepping process prior to application of antifouling paint Eliminates the need to sand fiberglass boats before painting by creating a chemical bond between the fiberglass surface and the first coat of antifouling paint. Quart. Primary Usage: Underwater, bare fiberglass, as tie-coat for bottom paint . Formulation: Underwater fiberglass primer for bottom paint. Applies Over: De-waxed bare fiberglass. to 2 hrs. Number of Coats Recommended: One coat, applied in one direction only.
Part No: YPA200/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Primers, Undercoats & Non-Skid->360R Under Metal
Versatile underwater primer with a variety of usesUniversal primer for underwater metal surfaces including steel and aluminum hulls and underwater running gear provides a barrier to reduce pitting of metal from galvanic corrosion. Use as a primer for antifouling paint over sanded fiberglass, wood or over an unknown antifouling paint. Primary Usage: Underwater metal surfaces . Formulation: Anti-corrosive underwater metal primer . Number of Coats Recommended: Three/four. Coverage: Brush: 52sq.
Part No: YPA984/1
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Primers, Undercoats & Non-Skid->360R Under Metal
Versatile underwater primer with a variety of usesUniversal primer for underwater metal surfaces including steel and aluminum hulls and underwater running gear provides a barrier to reduce pitting of metal from galvanic corrosion. Use as a primer for antifouling paint over sanded fiberglass, wood or over an unknown antifouling paint. Primary Usage: Underwater metal surfaces . Formulation: Anti-corrosive underwater metal primer . Number of Coats Recommended: Three/four. Coverage: Brush: 52sq.
Part No: YPA984/QT
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Trilux Prop & Drive Antifouling Paint
For aluminum outdrives, outboards and hulls Trilux® Prop & Drive has been specially formulated with Biolux™ to be the safest & most effective product for use on aluminum outdrives & outboards. When applied over properly primed aluminum Trilux® Prop & Drive with Biolux™ will provide good antifouling protection. One can covers approximately 22sq. ft. (one lower unit). Recommended Usage: Fresh, salt, brackish water; trailerable, dry-stored boats; aluminum lower units- outdrives .
Part No: YPA985N/16
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Topside Paint
Strictly for spray applicationsSpeeds up the cure process of Perfection Two-Part Polyurethane. Should only be used for spray application. Highly reactive material reduces cure time of Perfection Two-Part Polyurethane. Decreases pot life (working life) of Perfection.
Part No: YQA100/250
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil -> Topside Paint
Achieve professional-quality results with this simplified two-part painting system Simpler to use then other two-part polyurethanes, Perfection has been formulated to enable “do-it-yourselfers” to achieve professional quality results with ease on topsides, superstructure and decks. It is resistant to a wide range of chemicals, including fuels, mild acids and detergents. May be brushed, rolled, or sprayed over primed fiberglass, wood, aluminum, or steel. Number of Coats Recommended: Two/three .
Part No: YZM914KIT/QT
|
|
|
|
Home -> Cordage -> Rigging Products->Copper Oval Sleeves
.
Part No: Z0753-0001-W
|
|
|
|
Home -> Cordage -> Rigging Products->Copper Oval Sleeves
.
Part No: Z0753-0002-W
|
|
|
|
Home -> Cordage -> Rigging Products->Copper Oval Sleeves
.
Part No: Z0753-0003-W
|
|
|
|
Home -> Cordage -> Rigging Products->Copper Oval Sleeves
.
Part No: Z0753-0004-W
|
|
|
|
Home -> Cordage -> Rigging Products->Copper Oval Sleeves
SWAGE, 3/16IN SLEEVE.
Part No: Z0753-0005-W
|
|
|
|
Home -> Cordage -> Rigging Products->Copper Oval Sleeves
7/32IN SLEAVE.
Part No: Z0753-0006-W
|
|
|
|
Home -> Cordage -> Rigging Products->Copper Oval Sleeves
.
Part No: Z0753-0007-W
|
|
|
|
Home -> Seating & Covers -> Tables
Designed to receive a dual tapered column. The Z10-4070 is unique in its design that it can be used as both a table support or seat/table base. W9 x D7/8" . Dual Taper.
Part No: Z10-4070BLY76MM
|
|
|