Top Sellers
Power Bubbles 12V DC Aerator from MARINE METALS
This system runs on low current as it's dual bellows aerate up to 2L per minute of air. It saturates circulating water with oxygen. Double discharge allows aeration of one or two livewells. Increases flow capacity. Includes 10' of air tubing. Two large airstones allow the pump to be mounted in any protected area. Suitable for fresh or saltwater. Two anti-siphon valves protect pump against water intrusion. Quietly operates with solid-state circuits. Draw: 1/4A at 12V DC.
|
Stern Three-Mile LED Light from ATTWOOD
Energy-efficient three-mile 12" pole anchor/masthead and transom lights. Solid stainless hardware for corrosion resistance and unsurpassed polished appearance. Pole light is direct replacement for Perko 1181DPO CHR used on most Sea Ray boats. Case Material: Stainless steel . Mounting Hardware: Not included . Pole Diameter: 3/4" . Pole Material: Anodized aluminum . Draw: 0. 15A (1. 8W@12V DC) . Volts: 12V DC.
|
Panel Mount Thermal Circuit Breaker, 50A from BLUE SEA SYSTEMS
An economical solution for high amperage loads where dependability is required in marine environments. Waterproof and ignition-protected (conforming to SAE J1171) so these circuit breakers are safe for installation aboard gasoline-powered boats. Ideal for branch circuits, windlasses, inverters and watermakers. False-trip free—designed to trip when subjected to a fault current. Available in panel and surface mounts. Interrupt Rating: 3000A at 12V DC. Voltage Compatibility: 42V DC.
|
Fuel Sending Unit Only - 4-24'' Tank from TELEFLEX
Complete kit includes a reliable dash-mount gauge with a black face and white numerals. The triple patented sending unit has an adjustable float arm and U-channel that fits virtually all tanks from 4"-24" deep. Compatible with 12V DC systems with common or insulated ground.
|
Dual Warning Light and Buzzer from COLE HERSEE
Works with oil pressure, temperature, halon extinguishers, etc Use with grounded or ungrounded switches For use with Marine Engine Warning Alarm Kit Steel case measures 1-7/8"D x 1"W x 1-11/32"H Fits panels to 13/64" thick 12V DC .
|
Tachometer/System Check (4"), Johnson/Evinrude outboard, 7000RPM from FARIA INSTRUMENTS
Over 50 years of experience are behind every one of these Faria instrument gauges. They’re designed with an eye for sophistication and a mind for value. Perimeter lighted white dial with stylish blue and black graphics. Polished stainless steel bezel. Contoured black pointer and domed glass lens. All gauges are 12V DC with negative ground and are all internally illuminated unless otherwise noted. Include backclamp, hardware, and installation instructions. Mfr. ’s lifetime limited warranty.
|
500gph 12V Bilge Pump, 1.9A Draw at 12V DC, 3/4" Port, 4"H x 2-3/8"W from RULE INDUSTRIES
An internal computer chip cycles these pumps on every 2. 5 minutes, then quickly shuts them down if no water is detected. Built-in strainer bases snap off to make cleaning easy. Completely submersible, rust-proof, corrosion-proof and ignition-protected. Three-way wiring enables connection to a switch for manual override or indicator light. Small 500gph pump is designed to handle spray and rainwater. Built-In Switch: Yes, cycles every 2. 5 min.
|
Whale Gulper 220 Pump, 12V DC, Draw: 2.4A from WHALE PUMPS
Use this 3. Large 3/4" inlet and outlet valves are cut at 45° angles to minimize flow restriction. Ports rotate to the position you need to facilitate hose connections and it mounts vertically or horizontally—making installation a snap! It can run dry for extended periods without burnout and boasts a large diaphragm that generates up to 13' of lift. Rubber mounting feet reduce noise. Features: Will run dry without damage and pump a mixture of air and water . Large single diaphragm .
|
800gph Tsunami Bilge Pump, 2.5A @ 12V DC Draw, 3/4" Port, 4-3/8"H x 3-1/2"W from ATTWOOD
Versatile Tsunami pumps feature interchangeable, twist-and-lock cartridges that reduce maintenance time. All wires are caulked and tinned to prevent water wicking. Rugged glass and mineral-filled polymer construction resists chemicals, fuel and detergents and the compact, low-profile design eases installation in tight spaces.
|
Float Switch from SHURFLO
Offered with or without a protective cage, this non-mercury float switch utilizes mechanical contacts for reliable bilge pump activation. Includes 3', tinned wire leads. May be mounted apart from pump or snapped into base plate of Shurflo 380, 500, 700 and 1000gph pumps. 4. 4"L x 3. 6"W x 1. 3"H. For use with 12V and 24V DC pumps. ABS plastic. Two year limited warranty. Activation Method: Float with mechanical contacts .
|
12V Reversible Flo-Master Vane Pump from GROCO
Rigid-vane pumps for pumping water, oil or diesel. Positive-displacement pump is self-priming to 2’. Long-lasting, continuous-duty, ignition-protected motor has ball bearings and a #316 stainless-steel shaft Application: General light to intermittent duty utility pumping . Gallons Per Minute: 6. 5 (oil) . Material: Bronze pumphead, stainless shaft . Port Sizes: Male garden hose or 1/2" female NPT inlet & outlet . Dimensions: 3 3/8"H x 4 3/8"W x 7 1/2"L .
|
Deck Mate 25 Boat Anchor Windlass from POWERWINCH
Compact, deck-mounted windlass has power up/free-fall down capabilities and includes a built in light for added convenience. With low power draw and free fall deployment, this anchor winch puts less stress on your battery for longer battery life. Its small footprint takes up less deck space to mount and the spur gear train allows fast retrieval speeds and minimal current draw. Gear feature prevents rope from over running during anchor deployment. Style: Horizontal . Boat Length: Up to 25'' .
|
12V Blaster Washdown Pump, 3.5 GPM from SHURFLO
Blast the grimiest decks clean with one of these durable freshwater/saltwater pumps. Positive-displacement three/four chamber diaphragm design is self-priming up to 6' and can run dry without damage. Include 3/4" and 5/8" garden hose adapters. Pro Blaster features higher capacity and a seamless motor shell for enhanced protection in saltwater environments. Suitable for mounting in wet locations. Include fittings and Blaster spray nozzle. Switch Type: Sealed 45psi pressure switch .
|
Contura Rocker Switch, SPDT On/Off/On from COLE HERSEE
Waterproof switches are rated to IP66 for use on ship decks and with an LED light to indicate when the circuit is on. Several configurations are available for almost any application. Recommended for replacements in waterproof electrical panels with rocker switches to ensure waterproof integrity. Includes both black and gray covers. Both switches and covers are interchangeable with similar switches used as original equipment on many common boat types. Mounting Hole Size: 1. 450" x 0.
|
Surface-Mount Gasoline Fume Detector from MARINE TECHNLOGIES
Here’s affordable protection from a UL Marine-listed detector designed to warn you of explosive gas accumulation. With a warning light and audible alarm, the detector alerts you to gasoline fumes, hydrogen gas from batteries, propane, alcohol, acetone and other potentially explosive fumes at 20% of their explosive level. Features one-touch On/Off/Test operation. Alarms: Warning light and audible alarm. Minimum Vapor Level for Activation: 20% of Lower Explosive Limit . Controls: ON/OFF/Test .
|
|
12V DC Turbo Fan, 15mm from SEATECH, 1A Draw, 0, from HARKEN
|
|
Home -> Plumbing -> Fittings & Valves->Quick Connect Plumbing Fittings
Not only are they original equipment on Hatteras, Hunter, Wellcraft, and Sea Ray yachts, but these easy-to-use quick-connect fittings make your plumbing installation and repairs a snap! Leak-free connections can be made with hot or cold potable, fresh - or saltwater in boats and RVs. No screwing or clamping required. To install, cut piping to correct length, then push pipe into fitting until it hits the internal stop. To disconnect, push in on fitting collar and hold down while removing pipe.
Part No: 002417-10
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Quick Connect Plumbing Fittings
Not only are they original equipment on Hatteras, Hunter, Wellcraft, and Sea Ray yachts, but these easy-to-use quick-connect fittings make your plumbing installation and repairs a snap! Leak-free connections can be made with hot or cold potable, fresh - or saltwater in boats and RVs. No screwing or clamping required. To install, cut piping to correct length, then push pipe into fitting until it hits the internal stop. To disconnect, push in on fitting collar and hold down while removing pipe.
Part No: 002419-1008
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Quick Connect Plumbing Fittings
Not only are they original equipment on Hatteras, Hunter, Wellcraft, and Sea Ray yachts, but these easy-to-use quick-connect fittings make your plumbing installation and repairs a snap! Leak-free connections can be made with hot or cold potable, fresh - or saltwater in boats and RVs. No screwing or clamping required. To install, cut piping to correct length, then push pipe into fitting until it hits the internal stop. To disconnect, push in on fitting collar and hold down while removing pipe.
Part No: 002423-10
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Quick Connect Plumbing Fittings
Not only are they original equipment on Hatteras, Hunter, Wellcraft, and Sea Ray yachts, but these easy-to-use quick-connect fittings make your plumbing installation and repairs a snap! Leak-free connections can be made with hot or cold potable, fresh - or saltwater in boats and RVs. No screwing or clamping required. To install, cut piping to correct length, then push pipe into fitting until it hits the internal stop. To disconnect, push in on fitting collar and hold down while removing pipe.
Part No: 002439-1515
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Quick Connect Plumbing Fittings
Not only are they original equipment on Hatteras, Hunter, Wellcraft, and Sea Ray yachts, but these easy-to-use quick-connect fittings make your plumbing installation and repairs a snap! Leak-free connections can be made with hot or cold potable, fresh - or saltwater in boats and RVs. No screwing or clamping required. To install, cut piping to correct length, then push pipe into fitting until it hits the internal stop. To disconnect, push in on fitting collar and hold down while removing pipe.
Part No: 002440-1515
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Quick Connect Plumbing Fittings
Not only are they original equipment on Hatteras, Hunter, Wellcraft, and Sea Ray yachts, but these easy-to-use quick-connect fittings make your plumbing installation and repairs a snap! Leak-free connections can be made with hot or cold potable, fresh - or saltwater in boats and RVs. No screwing or clamping required. To install, cut piping to correct length, then push pipe into fitting until it hits the internal stop. To disconnect, push in on fitting collar and hold down while removing pipe.
Part No: 002443-0415
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Quick Connect Plumbing Fittings
Not only are they original equipment on Hatteras, Hunter, Wellcraft, and Sea Ray yachts, but these easy-to-use quick-connect fittings make your plumbing installation and repairs a snap! Leak-free connections can be made with hot or cold potable, fresh - or saltwater in boats and RVs. No screwing or clamping required. To install, cut piping to correct length, then push pipe into fitting until it hits the internal stop. To disconnect, push in on fitting collar and hold down while removing pipe.
Part No: 002475-15
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Quick Connect Plumbing Fittings
Not only are they original equipment on Hatteras, Hunter, Wellcraft, and Sea Ray yachts, but these easy-to-use quick-connect fittings make your plumbing installation and repairs a snap! Leak-free connections can be made with hot or cold potable, fresh - or saltwater in boats and RVs. No screwing or clamping required. To install, cut piping to correct length, then push pipe into fitting until it hits the internal stop. To disconnect, push in on fitting collar and hold down while removing pipe.
Part No: 002476-15
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights->Navigation Lights - Series 3562
White light mounts on any flat surface for powerboats and sailboats to 12m. Single 10W bulb. Gasketed lens prevents water penetration in rough conditions. For mounting; suspension from a halyard not recommended. 2nm visibility. Black base. Type: All-Around . Case Material: Polycarbonate . Case Dimensions: 2-5/16" dia. x 2-5/8"H . Mounting Hardware: Two RHMS (sold separately) .
Part No: 002492201
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Light Acc.
Double-contact bayonet socket with black plastic body, 3/4"dia.
Part No: 0024DP1
|
|
|
|
Home -> Sailboat -> Tiller & Rudder
Tests show that release loads can be varied between 25kg & 240kg (50lb & 520lb) Note that smaller or worn ropes release at higher loads than larger or new ropes .
Part No: 002570-1
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Quick Connect Plumbing Fittings
Not only are they original equipment on Hatteras, Hunter, Wellcraft, and Sea Ray yachts, but these easy-to-use quick-connect fittings make your plumbing installation and repairs a snap! Leak-free connections can be made with hot or cold potable, fresh - or saltwater in boats and RVs. No screwing or clamping required. To install, cut piping to correct length, then push pipe into fitting until it hits the internal stop. To disconnect, push in on fitting collar and hold down while removing pipe.
Part No: 002609-1215
|
|
|
|
Home -> Interior, Flags & Gifts -> Gifts -> Gifts & Specialty Items
Stowable Backgammon - a real classic that is fun for everyone onboard! And don't worry about losing the small pieces in rough seas. the backgammon set is magnetic! The backgammon case zips open to reveal a cloth playing field. Everything you need to start playing right away.
Part No: 00283
|
|
|
|
Home -> Electrical -> Switches, Fuses & Accessories
Simple on/off switch rated for 500A for 10 seconds/100A continuous, with removable red key, included. Replacement key available.
Part No: 002843011
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting->#2984 Navigation Lights for Boats to 65'7" (20 meters)
Very similar to #3562 lights, with larger lamps and size for greater visibility. Bulb hangs to reduce corrosion on socket. For power or sailboats to 65. 6'. Acrylic lens. 25W bulbs in colored lenses produce 2nm visibility, stern light has 2nm visibility, while masthead light has 3nm visibility. Black housing. Case Material: Polycarbonate . Case Dimensions: 4. 24"H x 4. 25"W x 3.
Part No: 002984305
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights->#2984 Navigation Lights for Boats to 65'7" (20 meters)
Very similar to #3562 lights, with larger lamps and size for greater visibility. Bulb hangs to reduce corrosion on socket. For power or sailboats to 65. 6'. Acrylic lens. 25W bulbs in colored lenses produce 2nm visibility, stern light has 2nm visibility, while masthead light has 3nm visibility. Black housing. Case Material: Polycarbonate . Case Dimensions: 4. 24"H x 4. 25"W x 3.
Part No: 002984315
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights->#2984 Navigation Lights for Boats to 65'7" (20 meters)
Very similar to #3562 lights, with larger lamps and size for greater visibility. Bulb hangs to reduce corrosion on socket. For power or sailboats to 65. 6'. Acrylic lens. 25W bulbs in colored lenses produce 2nm visibility, stern light has 2nm visibility, while masthead light has 3nm visibility. Black housing. Case Material: Polycarbonate . Case Dimensions: 4. 24"H x 4. 25"W x 3.
Part No: 002984325
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights->#2984 Navigation Lights for Boats to 65'7" (20 meters)
Very similar to #3562 lights, with larger lamps and size for greater visibility. Bulb hangs to reduce corrosion on socket. For power or sailboats to 65. 6'. Acrylic lens. 25W bulbs in colored lenses produce 2nm visibility, stern light has 2nm visibility, while masthead light has 3nm visibility. Black housing. Case Material: Polycarbonate . Case Dimensions: 4. 24"H x 4. 25"W x 3.
Part No: 002984335
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights->#2984 Navigation Lights for Boats to 65'7" (20 meters)
Very similar to #3562 lights, with larger lamps and size for greater visibility. Bulb hangs to reduce corrosion on socket. For power or sailboats to 65. 6'. Acrylic lens. 25W bulbs in colored lenses produce 2nm visibility, stern light has 2nm visibility, while masthead light has 3nm visibility. Black housing. Case Material: Polycarbonate . Case Dimensions: 4. 24"H x 4. 25"W x 3.
Part No: 002984345
|
|
|
|
Home -> Sailboat -> Blocks -> Blocks->2.25" Blocks
The original Harken block Used for main and jib sheets on course racing keelboats, scows and dinghies with large mains. Often used for spinnaker halyards and sheets on small offshore boats. Swivel blocks feature a three-way head system with a set screw. Blocks with cams feature adjustable cam arms and reversible cam cleats. Where applicable, blocks use #8 fasteners. Sheave: Delrin. Bearings: Delrin ball bearings. Sheave Size: 2-1/4" (57mm). Line Diameter: 7/16" max.
Part No: 003
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting->Replacement Lenses for Perko Navigation Lights
Replacement lenses for many of the popular styles of Perko Nav Lights on vessels under 20 meters.
Part No: 0030DP0001
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting
The collar set contains 4 collars: 1 each locking, large-threaded, small-threaded and screw-on collars.
Part No: 0030DP0002
|
|
|
|
Home -> Ventilation -> Air Conditioning & Cooling -> Interior Fans->12V & 24V Turbo Fans
Multi-directional for custom cooling aboard These fans are just right for circulating air on the bridge or inside the steering station because you can point them in almost any direction. Plastic blades are protected by a high-impact plastic guard. 5,000-hour motors. Easy to install, with 4 1/2' cable, included. Capacity: 125cu. ft. /min. . Blade: Soft plastic (3) . Safety Features: Protective grille . Dimensions: 7-5/16"W x 7-5/8"H x 3-3/4"D .
Part No: 003361002
|
|
|
|
Home -> Ventilation -> Air Conditioning & Cooling -> Interior Fans->12V & 24V Turbo Fans
Multi-directional for custom cooling aboard These fans are just right for circulating air on the bridge or inside the steering station because you can point them in almost any direction. Plastic blades are protected by a high-impact plastic guard. 5,000-hour motors. Easy to install, with 4 1/2' cable, included. Capacity: 125cu. ft. /min. . Blade: Soft plastic (3) . Safety Features: Protective grille . Dimensions: 7-5/16"W x 7-5/8"H x 3-3/4"D .
Part No: 003361012
|
|
|
|
Home -> Ventilation -> Air Conditioning & Cooling -> Interior Fans->12V & 24V Turbo Fans
Multi-directional for custom cooling aboard These fans are just right for circulating air on the bridge or inside the steering station because you can point them in almost any direction. Plastic blades are protected by a high-impact plastic guard. 5,000-hour motors. Easy to install, with 4 1/2' cable, included. Capacity: 125cu. ft. /min. . Blade: Soft plastic (3) . Safety Features: Protective grille . Dimensions: 7-5/16"W x 7-5/8"H x 3-3/4"D .
Part No: 003361022
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights->#3562 Navigation Lights for Boats to 39'4" (12 meters)
Compact navigation lights with modern styling. Completely waterproof, yet vented. Break-resistant polycarbonate housing snaps together without screws. Bulb snaps into a holder supported above condensing surfaces. Acrylic lens. 10W bulbs in colored lenses are visible 1nm. ; stern light is visible 2nm. Masthead light is visible 2nm. Case Material: Polycarbonate . Case Dimensions: 3"H x 2. 5"W x 2"L .
Part No: 003562005
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights->#3562 Navigation Lights for Boats to 39'4" (12 meters)
Compact navigation lights with modern styling. Completely waterproof, yet vented. Break-resistant polycarbonate housing snaps together without screws. Bulb snaps into a holder supported above condensing surfaces. Acrylic lens. 10W bulbs in colored lenses are visible 1nm. ; stern light is visible 2nm. Masthead light is visible 2nm. Case Material: Polycarbonate . Case Dimensions: 3"H x 2. 5"W x 2"L .
Part No: 003562015
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting->#3562 Navigation Lights for Boats to 39'4" (12 meters)
Compact navigation lights with modern styling. Completely waterproof, yet vented. Break-resistant polycarbonate housing snaps together without screws. Bulb snaps into a holder supported above condensing surfaces. Acrylic lens. 10W bulbs in colored lenses are visible 1nm. ; stern light is visible 2nm. Masthead light is visible 2nm. Case Material: Polycarbonate . Case Dimensions: 3"H x 2. 5"W x 2"L .
Part No: 003562025
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting->#3562 Navigation Lights for Boats to 39'4" (12 meters)
Compact navigation lights with modern styling. Completely waterproof, yet vented. Break-resistant polycarbonate housing snaps together without screws. Bulb snaps into a holder supported above condensing surfaces. Acrylic lens. 10W bulbs in colored lenses are visible 1nm. ; stern light is visible 2nm. Masthead light is visible 2nm. Case Material: Polycarbonate . Case Dimensions: 3"H x 2. 5"W x 2"L .
Part No: 003562035
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights->#3562 Navigation Lights for Boats to 39'4" (12 meters)
Compact navigation lights with modern styling. Completely waterproof, yet vented. Break-resistant polycarbonate housing snaps together without screws. Bulb snaps into a holder supported above condensing surfaces. Acrylic lens. 10W bulbs in colored lenses are visible 1nm. ; stern light is visible 2nm. Masthead light is visible 2nm. Case Material: Polycarbonate . Case Dimensions: 3"H x 2. 5"W x 2"L .
Part No: 003562045
|
|
|