2-Tank System, 30/35” Gauge from HART SYSTEMS, INC.
Convenient, easy to use, simple to install and far superior to a dip stick, sight glass or an electric float gauge, Tank Tender uses air pressure to provide accurate readings for up to ten tanks. No electrical connection is necessary. With this system, you just select a tank to measure, pump in a small amount of air from the bridge and in two or three seconds you have a reading. We offer systems here for 30" deep tanks. Panels measure 4"W x 8"H x 2-7/8"D.

1/4" NPT X 3/8" Brass hose barb from MOELLER
1/4 NPT X 3/8" Brass Hose barbs with male threads.

Circlips, Package of Five (5) from LEWMAR
Spares Kit, Single-Speed Winches For all single-speed winches less than 11 years old, includes 4 pawls, 4 pawl springs, 4 circlips. . Spares Kit, Two-Speed Winches For all two-speed and self-tailing winches to 16ST-66ST. Includes 2 circlips, 8 pawls, 12 pawl springs, 3 keys, 8 gear spindle sleeves, 2 collets . Spares Kit, Three-Speed Winches For all three-speed nonself-tailing winches to 65. Includes 4 circlips, 8 pawls, 18 pawl springs, 4 plungers, 6 plunger springs, 2 closing rings .

2-5/8" x 1-1/2" Euro Utility Hinge from WEST MARINE
Stamped utility hinge with 1/2" offset from TACO. Made of marine grade 304 stainless steel with polished finish, non-corrosive utility hinge is ideal for hatches, cabinets, and doors inside and outside the boat. Measures 2-5/8" x 1-1/2" x .

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Pro-Pull Tool Only from NATIONAL PRODUCTS
PRO-PULL Kits let you quickly remove 3- and 4-blade propellers from inboard shafts with a 3/4'' to 1 1/8'' diameter. The tool is made of heat-treated steel and features fine-thread screws for tremendous pulling force with very little effort. Kit also includes: Prop nut wrench, stainless cotter pin, brass prop-shaft key. Brass nylock prop nut, waterproof grease, and a rustproof carrying case.

Rim Latch Sets - Reverse Bevel with Flush Strike from PERKO
Chrome-plated zinc. Sliding lock button. Case size: 2 1/8'' x 1 3/4''. Escutcheon Size: 4 3/8'' x 1 1/4''. For Door: 5/8'' to 1 3/8''.

Flush Cup Door Latch from PERKO
Chrome plated zinc alloy with sliding lock button. For door thickness 3/4 to 1-1/8 inches. Supplied with black plastic spacer for surface mounting. Bevel/Strike Type: Regular w/Box. Case Dimensions: 2-1/8 x 1-3/4 .

West Marine/SOSpenders PFD Rearming Kit, 3/8" Threaded Cylinder Neck Dia. from WEST MARINE
West Marine/SOSpenders PFD Rearming Kit Style: Automatic. Cylinder Weight: 38g. Cylinder Neck Diameter: 3/8" or 1/2" threaded. Inflator Type: Halkey-Roberts. Kit Contents: Cylinder, green pin, bobbin. PFD Brands Commonly Used With*: West Marine/SOSpenders PFD . Inflator Number: V85000. *The column "PFD Brands Commonly Used With" is not all inclusive. Rearming Kits may be used with other brands and vests.

Flo-Master Centrifugal Pump Service Kit from GROCO
Groco Flo-Master Centrifugal Pump Top-of-the-line pump for baitwell circulation, hot/cold water circulation, diesel transfer, shower pumpout or low-pressure washdown. Ignition-protected motor has a #316 stainless steel shaft for extra long life. Not self-priming, so a flooded inlet is required . Not submersible . 17 GPM at 0' . Ports: 3/4" NPT inlet; garden hose or 1/2" NPT outlet . Draw: 5. 5A at 12V DC .

Boat Vent II from TAYLOR
The newest in boat cover venting and support Don't let your interior suffer from mold and mildew damage. The patented Boat Vent II installs quickly and easily, with no screws or fasteners. The venting area provides for greater volume of exhaust air while closing the top to bottom gap - keeping water out!. The Boat Vent II is manufactured from a superior grade polycarbonate blend material for strength and UV resistance and will accommodate either 3/4" or 7/8" support poles.

FNPT Brass Reducer Fuel Fitting, 1/4" NPT X 1/8" from MOELLER
High quality brass reducer.

Brass Reducer, 1/4"NPT x 1/8" FNPT from MOELLER
Barb-Fuel 1/4Fnp x 1/8Mnpt Brs|Barb-Fuel 1/4Fnp x 1/8Mnpt Brs.

Replacement Delrin Roller, 2-1/2" Dia., 1-3/4 Width from LEWMAR
Anchor rollers make dropping and weighing anchor easier on you and your boat. They help reduce chafe, prevent scratches and dings to your boat’s finish and provide a secure place to store your anchor when used in conjunction with an optional chain stopper or tensioner. We stock rollers to fit the most common combinations of anchor, mounting style and boat. Installation note: overhanging anchor rollers should be supported along at least 2/3 of their length. Easily installed using common tools.

Step Pad, 10-3/4" x 5-1/4", Blue from LEWMAR
Maintain your footing under all conditions! Self-adhesive, diamond-patterned, nonskid pads are great for decks, steps, dinghy floors, personal watercraft, etc. They resist wear and tear, peeling, saltwater, fuels and chemicals. Pads have rounded edges and are precut to fit most common step sizes. Trim with scissors for a custom fit. Peel-and-stick installation. Sold in pairs.