Top Sellers
|
|
Clamp-On Rod Holder - 1 1/4"ID Horizontal, Gold from WEST MARINE
Silver or gold tubes are anodized for long life in the marine environment. Fabricated from cold drawn aluminum with no unsightly weld seams. Available in aluminum schedule pipe sizes 3/4" thru 1 1/4" in horizontal and vertical models. If using stainless steel tube, please go down 1/4" in size. Type:Clamp on. # of Rods:One. Material:Aluminum. Lining:White vinyl. Diameter:Rod holder is 1 5/8" ID. Mount:Clamp on.
|
2-5/8" x 1-1/2" Euro Utility Hinge from WEST MARINE
Stamped utility hinge with 1/2" offset from TACO. Made of marine grade 304 stainless steel with polished finish, non-corrosive utility hinge is ideal for hatches, cabinets, and doors inside and outside the boat. Measures 2-5/8" x 1-1/2" x .
|
1/8" NPT X 5/16" Brass hose barb from MOELLER
1/8 NPT X 5/16" Brass hose barbs with male threads.
|
Hose Adapter, From 1-1/8" to 3/4"-5/8" from RULE INDUSTRIES
#69 is stepped & adapts from 1-1/8" to 3/4" - 5/8" #57 is an elbow & adapts from 1-1/8" to 1" NPT #67 adapts from 1-1/2" to 1-1/8".
|
|
|
Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
|
1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .
|
Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .
|
Tubing-Alu 7/8X20' from WEST MARINE
Bright 304 polished stainless steel or bright anodized aluminum. Used for a multitude of applications including grab rails, bow rails, and canvas top frames. Match materials between components to minimize corrosion. Stainless has . 049" wall thickness . Aluminum has . 058" wall thickness . Use 7/8" tubing for smaller powerboats . Use 1" tubing for sailboats and larger powerboats . Available in 6', 12' and 20' lengths .
|
Tubing SS 1''X20' from WEST MARINE
Bright 304 polished stainless steel or bright anodized aluminum. Used for a multitude of applications including grab rails, bow rails, and canvas top frames. Match materials between components to minimize corrosion. Stainless has . 049" wall thickness . Aluminum has . 058" wall thickness . Use 7/8" tubing for smaller powerboats . Use 1" tubing for sailboats and larger powerboats . Available in 6', 12' and 20' lengths .
|
Inflatable Boat Ladder from GARELICK
Contoured to hug the hull of inflatable boats. Attaches to floorboard or side with 3/8'' line and heavy-duty swivel snap. 1'' dia. anodized aluminum tubing with plastic rungs. Vinyl sleeves protect hull fabric.
|
Acetal Thru-Transom Scupper from WEST MARINE
One-way rubber flapper valve and thru-hull fitting. For 1-1/2"ID hose. Overall length: 6-1/4". Installation hole size: 2". Max.
|
Ultima Electronic Bilge Switch from JOHNSON PUMPS
The same switch that comes preinstalled on Johnson Ultima Combo Automatic Bilge Pumps. With no moving parts and totally sealed solid state electronics, this mercuryfree switch never corrodes or jams on debris. Activates/deactivates at 2" and 3/4" fluid levels. A three second delay prevents false starts. Rated to handle pumps up to 20 amps at 12V or 24V DC. Activation Method: Solid-state electronic . Dimensions: 2-3/8"H x 2-11/16"L x 1-1/8"D .
|
CP Bronze Strap Hinge - 1.125" H x 6" W from PERKO
Chrome plated bronze. Pin Height: 1-1/8" by 6" open width. Each hinge requires six #10 fasteners.
|
|
1, from FACNOR, Dia 1, 8" from C E SMITH, L-1-1, 12" Dia, 2" from C E SMITH
|
|
Home -> Fishing -> Fishing Accessories->Berkley® Trilene® Big Game™ 1/4 Lb. Custom Spool
Extreme fighting power for big game fish. Big Game features an abrasion resistant formula that runs through rod guides with less friction, but has the shock absorption and fighting power to handle big fish in fresh- and saltwater. Trilene® Big Game™ outperforms Ande and Maxima in key tensile and shock strength tests. Green 25 Lb.
Part No: 1068358
|
|
|
|
Home -> Electrical -> Electrical Wire->Primary Wire by the Foot
Sophisticated marine electronics and instruments only operate at peak potential when supplied with power at the right voltage, and that necessitates high-quality wire. Ordinary automotive-type wire can suffer a loss of conductivity, caused by corrosion and/or vibration, after a few months in the marine environment. Finally, Ancor wire is based on AWG (American Wire Gauge) wire sizes, which are 6–12% larger than SAE gauge wire, so you get more current-carrying ability than from similar SAE wire.
Part No: 106840
|
|
|
|
Home -> Fishing -> Fishing Accessories->Berkley Trilene® Big Cat™ Filler Spools
Berkley Trilene® Big Cat™ Filler Spools. Super tough line for super-tough fish. A super-tough monofilament that can haul big fish out of the heaviest cover. Super strong, abrasion resistant, shock absorbent, and easy to see. Easy to cast and handle.
Part No: 1068470
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Machine Screws - Slotted Round Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 1068A
|
|
|
|
Home -> Watersports -> PWC Parts & Accessories -> PWC Accessories->Personal Watercraft Fenders
Fender bottom hooks under bond flange. Flex areas provide hinge action that allows fender to conform to shape of watercraft. Inflation valve for air pressure adjustment. Includes suction cup and securing line.
Part No: 1069
|
|
|
|
Home -> Electrical -> Electrical Wire->Primary Wire by the Spool
Ordinary automotive-type wire can suffer a loss of conductivity after a few months in the marine environment, caused by corrosion and/or vibration. Premium Ancor wire will provide a lasting solution for your sophisticated marine electronics and instruments to operate at peak potential. 600V . 105°C dry, 75°C wet . Rated for oily and wet environments . Type 3 stranded, with 5–10 times more copper strands than Type 2 . Marine UL-listed, and meets the highest ABYC standards for AC or DC use .
Part No: 106910
|
|
|
|
|
Home -> Electrical -> Electrical Wire->Primary Wire by the Foot
Sophisticated marine electronics and instruments only operate at peak potential when supplied with power at the right voltage, and that necessitates high-quality wire. Ordinary automotive-type wire can suffer a loss of conductivity, caused by corrosion and/or vibration, after a few months in the marine environment. Finally, Ancor wire is based on AWG (American Wire Gauge) wire sizes, which are 6–12% larger than SAE gauge wire, so you get more current-carrying ability than from similar SAE wire.
Part No: 106940
|
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Machine Screws - Slotted Round Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 1069A
|
|
|
|
Home -> Electrical -> Shore Power -> Adapters, Plugs & Outlets->Shore Power Pigtail Adapters
Short jumper cord for wet locations Water-resistant adapters are fully molded, include sealing covers, and look like very short shore power cordsets. Recommended for use in wet locations. Pigtail adapters allow you to connect from one dockside receptacle (or other power source receptacle) to one boatside inlet or equipment of dissimilar power configuration. All components are covered by Marinco’s five-year warranty.
Part No: 106A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Retail Packs & Kits->Machine Bolts, Hex Head, Bulk Packs
Type 18-8 stainless steel.
Part No: 106C
|
|
|
|
Home -> Anchor & Docking -> Fenders & Docking->Dock Pro™ Dock Carts
Transport your gear from the car to the boat the easy way with this large capacity cart. Features a seven cubic foot heavy-duty, roto molded polyethylene tub that will not rust or rot. 20" plastic-rim wheels with roller bearings that will stand up well to the marine environment. Zinc-coated corrosion resistant hardware used throughout. 300 pound capacity. Material: roto-molded polyethylene tub. Zinc coated corrosion resistant hardware. Maximum Load Capacity: 300lbs. ft. .
Part No: 1070
|
|
|
|
Home -> Trailer & Parts -> Trailer Parts & Carriers -> Boat Support->Roller Shafts And Nuts
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
Part No: 10700A
|
|
|
|
|
Home -> Electrical -> Electrical Wire->Primary Wire by the Spool
Ordinary automotive-type wire can suffer a loss of conductivity after a few months in the marine environment, caused by corrosion and/or vibration. Premium Ancor wire will provide a lasting solution for your sophisticated marine electronics and instruments to operate at peak potential. 600V . 105°C dry, 75°C wet . Rated for oily and wet environments . Type 3 stranded, with 5–10 times more copper strands than Type 2 . Marine UL-listed, and meets the highest ABYC standards for AC or DC use .
Part No: 107010
|
|
|
|
|
Home -> Electrical -> Electrical Wire->Primary Wire by the Foot
Sophisticated marine electronics and instruments only operate at peak potential when supplied with power at the right voltage, and that necessitates high-quality wire. Ordinary automotive-type wire can suffer a loss of conductivity, caused by corrosion and/or vibration, after a few months in the marine environment. Finally, Ancor wire is based on AWG (American Wire Gauge) wire sizes, which are 6–12% larger than SAE gauge wire, so you get more current-carrying ability than from similar SAE wire.
Part No: 107012
|
|
|
|
|
Home -> Trailer & Parts -> Trailer Parts & Carriers -> Boat Support->Roller Shafts And Nuts
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
Part No: 10701A
|
|
|
|
|
Home -> Trailer & Parts -> Trailer Parts & Carriers -> Boat Support->Roller Shafts And Nuts
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
Part No: 10705A
|
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Machine Screws - Slotted Round Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 1070A
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->LS & LX Series Furlers
A drum bearing box with a steel thrust bearing between two large, self-lubricating polymer fiber bearings means that this furler has a smooth rotation under high axial (halyard) and lateral (sheet and furling line) loads. The head swivel, with the same bearing system as the drum, rotates smoothly, even under high loads. A halyard deflector wheel prevents troublesome halyard wraps. LS systems feature a non-removable drum, aluminum sail feeder and a fixed tack fitting. Ball Bearings: Torlon® .
Part No: 10716464600
|
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->LS & LX Series Furlers
A drum bearing box with a steel thrust bearing between two large, self-lubricating polymer fiber bearings means that this furler has a smooth rotation under high axial (halyard) and lateral (sheet and furling line) loads. The head swivel, with the same bearing system as the drum, rotates smoothly, even under high loads. A halyard deflector wheel prevents troublesome halyard wraps. LS systems feature a non-removable drum, aluminum sail feeder and a fixed tack fitting. Ball Bearings: Torlon® .
Part No: 10716794600
|
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Machine Screws - Slotted Round Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 1072
|
|
|
|
Home -> Anchor & Docking -> Fenders & Docking->Dock Pro™ Inflatable Dock Wheels
Smooth rolling wheels fend your vessel away from the dock. Molded-in standard-needle inflation valves let you adjust firmness. Hot dip galvanized hardware. Strong, 2"dia. axle housing on the 12" and 18" model, and 3/4" dia. axle housing on the 9" model. Material: Vinyl. Attachment Method: Galvanized hardware. Shock Absoption Mechanism: Inflated vinyl bumper.
Part No: 1072
|
|
|
|
|
Home -> Trailer & Parts -> Trailer Parts & Carriers -> Boat Support->Roller Shafts And Nuts
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
Part No: 10721A
|
|
|
|
|
Home -> Trailer & Parts -> Trailer Parts & Carriers -> Boat Support->Roller Shafts And Nuts
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
Part No: 10722A
|
|
|
|
|
Home -> Trailer & Parts -> Trailer Parts & Carriers -> Boat Support->Roller Shafts And Nuts
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
Part No: 10725A
|
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->LS & LX Series Furlers
A drum bearing box with a steel thrust bearing between two large, self-lubricating polymer fiber bearings means that this furler has a smooth rotation under high axial (halyard) and lateral (sheet and furling line) loads. The head swivel, with the same bearing system as the drum, rotates smoothly, even under high loads. A halyard deflector wheel prevents troublesome halyard wraps. LS systems feature a non-removable drum, aluminum sail feeder and a fixed tack fitting. Ball Bearings: Torlon® .
Part No: 10726464600
|
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->LS & LX Series Furlers
A drum bearing box with a steel thrust bearing between two large, self-lubricating polymer fiber bearings means that this furler has a smooth rotation under high axial (halyard) and lateral (sheet and furling line) loads. The head swivel, with the same bearing system as the drum, rotates smoothly, even under high loads. A halyard deflector wheel prevents troublesome halyard wraps. LS systems feature a non-removable drum, aluminum sail feeder and a fixed tack fitting. Ball Bearings: Torlon® .
Part No: 10726794600
|
|
|
|
|
Home -> Trailer & Parts -> Trailer Parts & Carriers -> Boat Support->Roller Shafts And Nuts
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
Part No: 10726A
|
|
|
|
|
Home -> Trailer & Parts -> Trailer Parts & Carriers -> Boat Support->Roller Shafts And Nuts
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
Part No: 10727A
|
|
|
|
|
Home -> Anchor & Docking -> Fenders & Docking->Dock Pro™ Inflatable Dock Wheels
Smooth rolling wheels fend your vessel away from the dock. Molded-in standard-needle inflation valves let you adjust firmness. Hot dip galvanized hardware. Strong, 2"dia. axle housing on the 12" and 18" model, and 3/4" dia. axle housing on the 9" model. Material: Vinyl. Attachment Method: Galvanized hardware. Shock Absoption Mechanism: Inflated vinyl bumper.
Part No: 1073
|
|
|
|
|
Home -> Trailer & Parts -> Trailer Parts & Carriers -> Boat Support->Roller Shafts And Nuts
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
Part No: 10730
|
|
|
