Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Series 250 Exhaust Hose, 7/8"ID, 1-3/16"OD, 565psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

3/8" Bow/Stern Eye - 1.03" ID Between Studs x 4.63" Thread Length from SUNCOR
Bow / Stern Eye 304 Stainless Steel - Formed . Each U-Bolt set includes four nuts (two standard and two beveled) . Includes one bow plate, and one stern plate. . Threads are "UNC". . Stock size: 3/8" . ID between studs: 1. 03" . Thread length: 2. 50" .

50' Braided Polyester Cord from NEW ENGLAND ROPES
A low-stretch cord that’s great for flag halyards, foredeck netting, or light-air spinnaker sheets. Length: 50'. Diameter: 1/8". Best use: Utility cord, flag halyards . Construction: Braided polyester . Breaking strength: 530lb. . Stretch: 3% at 15% of breaking strength .

5" ID, 45° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Delrin Sheave, 1/2" Max. Line Dia., 1-7/16" OD, 3/8" ID, 5/8" Width from SCHAEFER
Schaefer sheaves are designed to be compatible with Schaefer products, and are not intended for use in other manufacturer's blocks. Delrin sheaves are injection molded with UV inhibitors and monitored molding cycles for a stronger product.

WM Self-Coiling Hose - 15' from WEST MARINE
Featuring an improved flow rate and field-serviceable couplings! With an improved flow rate of 360gph, this hose delivers a powerful stream of water to make deck and boat wash-downs quick and easy. In the unlikely event of a rupture, the couplings can be removed with common hand tools, the hose shortened and the couplings replaced, which is a big advantage if you happen to be offshore! 90% usable length. Field-serviceable couplings. Strain relief at hose connection end'. 360gph flow rate.

P-Trap Fuel Surge Protector from ATTWOOD
One combined product eliminates the need to install both a fuel line vent and a surge protector. Inertia of surging fuel drives the surge ball against upper seat, closing the large vent opening and limiting passage to smaller openings, which reduces fuel flow and minimizes spillage. Operates in any orientation within 45° of vertical. Baffles resist water intrusion during normal sea conditions and washdown. Constructed of glass filled polypropylene to withstand oil, gas, alcohol blended fuels.

Tee Type Sanitation Hose Fitting, Slip Fitting Thread from SHIELDS RUBBER
Fiberglass-reinforced nylon fittings designed to fit Shields Series 101, 148 and 144 hoses without heating or special tools. Use in sanitation systems, deck drain systems and water tank fill.

Rubrail Insert - for Style #6, Model 341100 from TACO PRODUCTS
Rubber inserts add cushioning to your aluminum rubrails. . These fit styles #5, #6 and #7. Rub rails and inserts sold separately. .

Insert - for Taco #V21-9517, #V21-9501, #V21-9602, Per Foot from TACO PRODUCTS
Rubber inserts add cushioning to your aluminum rubrails. . These fit styles #5, #6 and #7. Rub rails and inserts sold separately. .

Acetal Thru-Transom Scupper from WEST MARINE
One-way rubber flapper valve and thru-hull fitting. For 1-1/2"ID hose. Overall length: 6-1/4". Installation hole size: 2". Max.

Flipper Pump from WHALE PUMPS
Easy back-and-forth action produces one-way discharge. Spout swivels. Made of nylon, aluminum and synthetic rubber. For 1/2"ID hose. Material: Nylon, aluminum, rubber . Capacity: 2gpm . Dimensions: 7-1/8"H x 6"dia. . Cutout Size: 2". Clearance: 4-1/2" .

Twisted Pair Wire with Shield from ANCOR MARINE
Similar to Ancor duplex wire, except that the conductors are twisted and surrounded by a copper shield for extra protection against noise and electrical interference. Red/black conductors. Recommended by ABYC for DC wiring near compasses and other magnetically - sensitive devices. Sold per foot. Wire Type: Twisted Pair . Construction: Tinned Copper . Conductors (Color and # of): 1 Red, 1 Black . Color of Exterior Insulation: White . Shielding: Copper Shield . Approvals: UL, ABYC, CSA .