Top Sellers
Fluke-Style Anchor Rail Mount from SCHAEFER
Safe off-the-deck stowage for Danforth-style anchors to 22lb. This anchor mount enables secure, off-the-deck storage and quick deployment of Danforth style anchors from 8-22 pounds. Mounts onto 1" diameter horizontal bow or stern rails and features a quick release mechanism with a locking hole to prevent accidental release. Closing latch enables one hand anchor engagement. 304 stainless steel.
|
Stainless-Steel “S” Hook, 3/16" Wire Dia., 5/8" Inside Width from SEAFIT
Stainless Steel "S" Hooks. Polished Stainless Steel Made in the U. S. A.
|
Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.
|
500 RC Windlass, 600lb. Max. Pull, Boat Length 35', 1/4"HT Chain, 1/2" Rope Rode Size, 62'–Chain; 45'–Rope Speed Up/Min., 60' Speed Down/Min., 60A–75A @12V Draw from MAXWELL
These low-profile windlasses feature a patented tension system that maintains resistance required to feed chain/rope rode into the locker instead of jamming it in the windlass. Designed for easy installation, the motor can be oriented in any of 12 positions below decks. Two pieces bolt together quickly. Gasketed, watertight base. For decks to 2 3/4" thick. Capstan models and extra-long shafts for thick decks are available by Special Order. Style: Vertical . Rode Type: Rope/chain .
|
29mm Carbo Clew Block Assembly from HARKEN
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.
|
3/8" Bow/Stern Eye - 1.03" ID Between Studs x 4.63" Thread Length from SUNCOR
Bow / Stern Eye 304 Stainless Steel - Formed . Each U-Bolt set includes four nuts (two standard and two beveled) . Includes one bow plate, and one stern plate. . Threads are "UNC". . Stock size: 3/8" . ID between studs: 1. 03" . Thread length: 2. 50" .
|
|
|
1/8" NPT X 5/16" Brass hose barb from MOELLER
1/8 NPT X 5/16" Brass hose barbs with male threads.
|
West Marine/SOSpenders PFD Rearming Kit, 3/8" Threaded Cylinder Neck Dia. from WEST MARINE
West Marine/SOSpenders PFD Rearming Kit Style: Automatic. Cylinder Weight: 38g. Cylinder Neck Diameter: 3/8" or 1/2" threaded. Inflator Type: Halkey-Roberts. Kit Contents: Cylinder, green pin, bobbin. PFD Brands Commonly Used With*: West Marine/SOSpenders PFD . Inflator Number: V85000. *The column "PFD Brands Commonly Used With" is not all inclusive. Rearming Kits may be used with other brands and vests.
|
3/16" Stock Dia. U-Bolt, 1-3/8” Thread Length, 1-3/16" Hole Spacing, 1" Eye Dia. from SEAFIT
Stainless steel U-Bolts have metric threads. The top plate is held in place by small ears that are forged into the U-bolt. Includes matching backing plate. ShWt .
|
|
|
1/4" NPT X 3/8" Brass hose barb from MOELLER
1/4 NPT X 3/8" Brass Hose barbs with male threads.
|
3/8" NPT Aluminum hose barb from MOELLER
3/8 NPT X 3/8" Aluminum hose barb with male threads.
|
1/4" NPT X 5/16" Brass hose barb from MOELLER
1/4 NPT X 5/16" Brass hose barbs with male threads.
|
Lube Tube Adapter for Yamaha, Nissan, Tohatsu, Honda (2-50hp) from WEST MARINE
Marine lower unit drain, flush and fill tool. Metal threaded fitting fits MerCruiser, OMC, Evinrude, Johnson, Honda (70-90hp), Volvo, Force and Gamefishier lower units. Quick, easy and clean way to change marine lower unit gear lube. For use with all 8- and 10-oz.
|
|
Quick Attach Stud, 16" Thread from SUNCOR, 8" Thread from SUNCOR
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0771-1610
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0771-2013
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0772-0703
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0772-0704
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0772-0904
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0772-0905
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0772-1005
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0772-1007
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0772-1307
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0772-1309
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0772-1609
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0772-1610
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0772-2013
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0775-0603
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0775-0604
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0775-0804
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0775-0805
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0775-1005
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0775-1006
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0775-1206
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0775-1208
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0775-1608
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0775-1610
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Stud Swage Fitting
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Stud mechanical swage fitting allows very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools. Working Load Limit (WLL) is determined by the WLL of the wire being used.
Part No: C0775-2012
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Toggle Swage Fittings
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Toggle mechanical swage fitting allows a self-aligning capability for a more flexible connection such as boat lifelines. Quick Attach fittings allow very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools.
Part No: C0778-0703
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Toggle Swage Fittings
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Toggle mechanical swage fitting allows a self-aligning capability for a more flexible connection such as boat lifelines. Quick Attach fittings allow very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools.
Part No: C0778-0704
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Toggle Swage Fittings
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Toggle mechanical swage fitting allows a self-aligning capability for a more flexible connection such as boat lifelines. Quick Attach fittings allow very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools.
Part No: C0778-0904
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Toggle Swage Fittings
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Toggle mechanical swage fitting allows a self-aligning capability for a more flexible connection such as boat lifelines. Quick Attach fittings allow very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools.
Part No: C0778-0905
|
|
|
|
|
Home -> Sailboat -> Rigging Products->Quick Attach™ Toggle Swage Fittings
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Toggle mechanical swage fitting allows a self-aligning capability for a more flexible connection such as boat lifelines. Quick Attach fittings allow very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools.
Part No: C0778-1007
|
|
|
|
|
Home -> Cordage -> Rigging Products->Quick Attach™ Toggle Swage Fittings
The advantage of "Quick Attach" over conventional fittings is the arrangement of the wedges on the outside of the cable which makes assembly much easier and allows different types of wire to be used with the same fitting. The Suncor Quick Attach Toggle mechanical swage fitting allows a self-aligning capability for a more flexible connection such as boat lifelines. Quick Attach fittings allow very fast attachment to any type of cable (1X19, 7X19, or 7X7) using only simple tools.
Part No: C0778-1309
|
|
|
