3/8 inch inline fuel filter from SIERRA
For use on McCulloch/Scott-Atwater, Suzuki Outboard and Yamaha Outboard 18-7831 is replacement for Johnson/Evinrude Outboard #398319.

CARB GASKET KIT from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Yamaha Carb Kit from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Replaces OMC P/N 378444 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Impeller, 18-3062 from SIERRA
Recommended replacement schedule is every 3 years for fresh water and every year for salt water Click to view a Sierra Impeller Application Chart (PDF) For further assistance, have your year & model information handy and call our Product Advisors at 1-800-BOATING.

For Chrysler/Force, 89-817109A2 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Fuel Filter Cartridge from SIERRA
FILTER Replaces: Mercruiser 35-866171A01 Fits: 350 Mag MPI Alpha/Bravo, 350 Mag MPI Horizon Alpha/Bravo, 350 Mag MPI Horizon MIE, 350 Mag MPI MIE, 496 MAG, 496 MAG H. O. , 5. 0 MPI Alpha/Bravo, 8. 1L Inboard, 8. 1L Inboard H. O. , MX 6.

Water Circulating Pump - #18-3581 - Chrysler Inbd # 3004886, 3619542, 3619859, 3745985 from SIERRA
Water Pumps The water pump is the heart of your inboard or I/O cooling system. All Sierra pumps are bidirectional and can be installed on reverse rotation engines. The pumps are also powder coated for additional protection. Includes mounting gasket. Pumps include brass bi-directional impellers, brass plugs and fittings, carbon resin seal, all mounting gaskets, stainless steel seal cup and spring, stainless steel back plate (where required), and powder coating for maximum corrosion protection.

Johnson/Evinrude Outboard Starter, 120 to 140hp V4 (1985-99), 10 tooth drive gear from SIERRA
Sierra's new and remanufactured starters are the only marine starters that meet Marine UL standards. Sierra's remanufactured starters all have new solenoids, drives, bushings, brushes and springs. The bodies are powder coated for greater corrosion resistance. Sierra has entered an agreement with United Technologies to market their complete line of outboard starters and components. All are 100% load tested . Our remanufactured starters are covered by Sierra's customer satisfaction warranty .

Sierra-Tube-Exhaust from SIERRA
Some larger V-8 engines that create a large amount of back pressure use exhaust tubes rather than bellows. This helps to relieve the excessive pressure and eliminate problems with premature bellows failure. In the past, the exhaust bellows would blow up like a balloon and cause the drive shaft bellows to rub against the yoke and U-joints causing holes in the bellows.

Prop Nut Kit, Yamaha V4/V6 from SIERRA
An excellent emergency item to carry in your toolbox, for those occasions when the prop nut is misplaced or lost.

Exhaust Flapper Valve - 4" from SIERRA
Heavy duty rubber flapper valve keeps following seas from entering exhaust outlet when moving slowly or stopping.

Johnson/Evinrude, motor only, for 2-wire systems, 90–225hp (1991–1999) from SIERRA
Tilt/Trim Motors, Outboard Applications.

20 Amp Pushbutton Thermal Circuit Breaker from SIERRA
Very common pushbutton breakers for DC loads. Uses two-blade terminals. Mounts in 3/8" hole. Can be used with a waterproof boot over the button. Buttons are white. Switch Type: Pushbutton . Voltage Compatibility: DC . Safety Features: Waterproof boots available . Housing Material: Plastic . Housing Dimensions: 1. 75" x 1.

Outdrive Gasket Set, 18-260, TR/TRS, 1973-1993 from SIERRA
Gasket and O-ring kits that seal the drive to the transom.