Replacement Gas Strut, 12" Compressed x 20" Extended Length, 40lb. Rating from TAYLOR
Reliable gas struts incorporate a strong annealed steel rod with a special coating for added corrosion resistance. Recommended by the manufacturer for use as dock box lid supports or hatch supports. Where use as a hatch cover support is desired, we recommend you base your selection upon the recommendation of the hatch manufacturer.

Replacement Element for OMC Outboards Only, No Bowl from RACOR-PARKER FILTRAT
Direct replacement for factory filters, only better! Aquabloc® filter medium removes virtually all the water from fuel. Water contamination is separated out and drops into the bowl where a drain plug allows easy, safe removal. Includes filter element and bowl, but not mounting head. Fuel Type: Gasoline. Flow Rate: 60 gph. Filtering Efficiency: 10 micron. Mounting Head: Varying styles for different engines. Inlets/Outlets: Depends on engine manufacturer. Bowl Material: See-through.

Hatch Riser Arm for 20" x 20" Hatch from TAYLOR
Replacement arms for Taylor hatches from 1987 to the present. Universal arms can be left or right.

Series 110 Gasoline Filter Replacement Element from RACOR-PARKER FILTRAT
Gasoline Filter Spin-On Replacement Elements.

Gas Fill & Tank Vent - Black from PERKO
Perko Gas Fill and Tank Vent This ingenious plastic deck fill has a vent with a flame arrestor built right into the fill flange. A flip-up cap eliminates the need for a deck key and no ground wire is required.

XA/XAS, Replacement Cam Kit from SPINLOCK
Cam Replacement & Upgrade Kits for XTS Powerclutches.

Gas Caddy from TODD ENTERPRISES
Move 28 gallons of Gas in our smooth-rolling caddy Store and transport fuel safely on docks or onboard. Gas Caddy holds 28 gallons of fuel. Includes 10' of UL Approved hose with static wire, molded hose brackets, UL Approved spring loaded nozzle, 3/4" UL Approved ball valve, aluminum non sparking axle, pneumatic tires with nylon bearings, nylon wheel hubs, vented cap and a molded-in baffle for strength & durability. All Caddies bear the UN Marking, “UN3H1W. ” Color-coded red.

Strainer for Round Rule Pump, 2800 - 3700 gph Flow Rate from RULE INDUSTRIES
Original replacement strainer base for your Rule Bilge Pump.

Bilge Pro Replacement Motor Cartridge for 500gph Pumps from JOHNSON PUMP
In the event of a problem, replacing your cartridge bilge pump motor is easy— provided you keep one of these on hand. Just pop out the old cartridge and pop in the new. Fit Johnson, West Marine Bilge Pro and Mayfair cartridge-style bilge and livewell pumps.

Gas Deck Fill Replacement Cap, Locking from PERKO
Includes grounding lug with screw and integral retainer for cap For 1 1/2" hose Impervious to gasoline.

Gas Deck Fill Replacement Cap, Plain from PERKO
Includes grounding lug with screw and integral retainer for cap For 1 1/2" hose Impervious to gasoline.

10mm Ball Stud pair from TAYLOR
Taylor 10mm Ball Stud pair.

Rechargeable Signal Air Horn from TAYLOR
Environmentally safe air horn uses air as a propellant, instead of the traditional gas-filled designs. It's economical too. no more expensive refills to buy. Recharges in seconds with a gas station air pump, air compressor, or any other mechanical compressed air source including hand pumps. Works in all weather extremes and can safely be used or stored near sources of heat. Provides approximately 20 blasts per charge. This loud horn puts out a powerful 120db. Meets all USCG regulations.

G. O'Day 222/Santana 525,Length 47", Height at tip 2 1/4", Width at butt 1 1/2", Width at tip 2" from WEST MARINE
Replace that old ugly tiller with a new hand-made laminated ash and mahogany wood tiller, made to fit your rudder hardware, and pre-finished with multiple coats of premium marine spar varnish. Choose the right length and profile, and the butt-end measurements to fit your rudderhead hardware. Can’t find a good fit? Idasailor Marine can custom-build a tiller to your measurements . Custom tillers are shipped direct within 10 days . Click HERE to open the PDF custom order form.

Replacement Cap with Gauge from MOELLER
Externally threaded cap fits Moeller tanks 031103, 031106, 031109, 031112, 031212. Scepter cap fits 4158, 4921, 3780 & 3781 tanks. Internal threaded cap fits 31612, 31615, 31515, 31818, 31620 & 31526 tanks.