Brass-Bristle Brush from SEAFIT
Solid brass bristles won't rust or corrodeLarge, plastic utility brush has solid brass bristles that won’t rust or corrode. Brass bristles are slightly softer than stainless steel and are therefore less intrusive to surfaces. Molded plastic handle provides solid, controlled grip. Bristles: 5/8"D. Overall length: 8 1/2". Molded plastic handle provides solid, controlled grip. 5/8"L bristles.

Solid Brass Vertical Action Galley Pump from FYNSPRAY
Vertical plunger pump with a gracefully arched spout. 50 strokes per gallon. 1"diameter tube. Fits 1/2"–5/8" hose. Requires 8 1/2" clearance below counter surface; 9 3/4" above Material: Brass. Capacity: 50 strokes/gal. Dimensions: 9 3/4"H. Cutout Size: 1 1/8". Clearance: 8 1/2".

8-1/2" Hatch Holder, Adjustable, for Hatches to 10lb. from MOONLITE MARINE
Stainless, spring-type holders “pop” into place to hold hatches, doors, table leaves, etc. Easy to install. Adjustable model allows opening between 10° and 80°.

Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Large Funnel - 5GPM, 10"H x 8-1/2"Dia., 100 Micron from WEST MARINE
Fuel/Water Separator These filters were tested by Powerboat Reports (March 2003) and rated better than other more expensive funnels. Teflon-coated, stainless-steel filter separates water and dirt from gasoline, diesel and kerosene fuels. Made from industrial standard electroconductive polypropylene that can be grounded for extra safety. Tested and rated by Powerboat Reports (March 2003) better than other more expensive funnels. Separate water and dirt from gasoline, diesel and kerosene fuels.

800gph Tsunami Bilge Pump, 2.5A @ 12V DC Draw, 3/4" Port, 4-3/8"H x 3-1/2"W from ATTWOOD
Versatile Tsunami pumps feature interchangeable, twist-and-lock cartridges that reduce maintenance time. All wires are caulked and tinned to prevent water wicking. Rugged glass and mineral-filled polymer construction resists chemicals, fuel and detergents and the compact, low-profile design eases installation in tight spaces.

Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.

Aft-Deck Shower System from ATTWOOD
This compact hot/cold shower stores neatly in its own compartment on the stern or in the head. Includes a handheld shower spray head with shutoff, 6' hose, hot/cold water controls and a cover. Easily hooked into your freshwater system. Compartment is drilled for six #8 fasteners. Material: High-impact plastic . Dimensions: 9-1/2"H x 5"W x 2-1/4"D . Hose Size: 6'L . Port Sizes: 1/2" NPT .

Spring Loaded Ring Pull, Square 2 x 2 3/8" from WEST MARINE
Spring-loaded ring immediately returns to flush when released. Type 304 stainless steel . Size: 2 x 2 3/8" .

"U" Bolt - Stainless Steel 3/8" Pad Eye from SEADOG
"U" Bolt - Stainless Steel Pad Eye.

Series 60 Orbit Block, Single Light-Load, 2-3/8" Sheave Size, 1,710lb. SWL, 4.7oz. from RONSTAN
These exceptionally strong blocks feature the performance Orbit sheave with captive Acetal ball bearings for side thrust loads, eliminating the need for side retainer plates. The 75mm webbing block (RF79107) can be used where swivel head and shackle attachment is not required to achieve further weight savings. Sheave Size: 2-3/8" (60mm) or 3" (75mm). Line Diameter: Series 60: 1/2" (12mm), Series 75: 9/16" (14mm). Cheek Material/Finish: Anodized aluminum.

5/16" Wire Rope Clamp from SEADOG
Investment Cast 316 Stainless Body / AISI 304 Stainless U-Bolt. Accepts 5/16" wire. 1-5/8" Long. 1-3/8" wide.

8mm (5/16") Stock Dia. Bolt, 4-5/16"L, 5/8" Hole Dia., 3" Stock Length, 1" Plate Dia. from SEADOG
Machined from 304 stainless steel.

1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .

West Marine/SOSpenders PFD Rearming Kit, 3/8" Threaded Cylinder Neck Dia. from WEST MARINE
West Marine/SOSpenders PFD Rearming Kit Style: Automatic. Cylinder Weight: 38g. Cylinder Neck Diameter: 3/8" or 1/2" threaded. Inflator Type: Halkey-Roberts. Kit Contents: Cylinder, green pin, bobbin. PFD Brands Commonly Used With*: West Marine/SOSpenders PFD . Inflator Number: V85000. *The column "PFD Brands Commonly Used With" is not all inclusive. Rearming Kits may be used with other brands and vests.