Top Sellers
1/4" NPT X 3/8" Brass hose barb from MOELLER
1/4 NPT X 3/8" Brass Hose barbs with male threads.
|
|
|
Rim Latch Sets - Reverse Bevel with Flush Strike from PERKO
Chrome-plated zinc. Sliding lock button. Case size: 2 1/8'' x 1 3/4''. Escutcheon Size: 4 3/8'' x 1 1/4''. For Door: 5/8'' to 1 3/8''.
|
|
|
Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.
|
Brass Reducer, 1/4"NPT x 1/8" FNPT from MOELLER
Barb-Fuel 1/4Fnp x 1/8Mnpt Brs|Barb-Fuel 1/4Fnp x 1/8Mnpt Brs.
|
2-Tank System, 30/35” Gauge from HART SYSTEMS, INC.
Convenient, easy to use, simple to install and far superior to a dip stick, sight glass or an electric float gauge, Tank Tender uses air pressure to provide accurate readings for up to ten tanks. No electrical connection is necessary. With this system, you just select a tank to measure, pump in a small amount of air from the bridge and in two or three seconds you have a reading. We offer systems here for 30" deep tanks. Panels measure 4"W x 8"H x 2-7/8"D.
|
Flush Cup Door Latch from PERKO
Chrome plated zinc alloy with sliding lock button. For door thickness 3/4 to 1-1/8 inches. Supplied with black plastic spacer for surface mounting. Bevel/Strike Type: Regular w/Box. Case Dimensions: 2-1/8 x 1-3/4 .
|
|
|
|
|
Rechargeable Signal Air Horn from TAYLOR
Environmentally safe air horn uses air as a propellant, instead of the traditional gas-filled designs. It's economical too. no more expensive refills to buy. Recharges in seconds with a gas station air pump, air compressor, or any other mechanical compressed air source including hand pumps. Works in all weather extremes and can safely be used or stored near sources of heat. Provides approximately 20 blasts per charge. This loud horn puts out a powerful 120db. Meets all USCG regulations.
|
Teak Plugs - 3/8" from SEAFIT
Use these teak plugs to cover screw heads or fill small holes for a beautiful smooth finish to your installation. Sizes: 1/4" 5/8" 5/16" 3/8" 1/2" 1".
|
Aft-Deck Shower System from ATTWOOD
This compact hot/cold shower stores neatly in its own compartment on the stern or in the head. Includes a handheld shower spray head with shutoff, 6' hose, hot/cold water controls and a cover. Easily hooked into your freshwater system. Compartment is drilled for six #8 fasteners. Material: High-impact plastic . Dimensions: 9-1/2"H x 5"W x 2-1/4"D . Hose Size: 6'L . Port Sizes: 1/2" NPT .
|
Holding Clips, 1/4" from BECKSON MARINE INC
Heavy-duty, nonmagnetic, noncorroding clips. Require four #8 FHWS fasteners.
|
|
|
|
4 from FASCO FASTENERS, 8 from FASCO FASTENERS
|
This site contains about 37,785 documents.
|
|
View by:
Title
|
Category
|
Manufacturer
|
Part No
|
Price
|
|
Page:
1
100
200
300
400
500
600
700
860
870
880
890
900
910
920
930
940
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
990
1,000
1,010
1,020
1,030
1,040
1,050
1,060
1,100
1,200
1,260
|
|
|
Home -> Fishing -> Fishing Accessories -> Rod Holders->Plastic Flush-Mount Rod Holders
These light- to medium-duty rod holders are made of high-impact ABS plastic so you‘ll never have to worry about rust Flange size is 3 1/2" x 4 1/4". Flange has a slightly textured top surface.
Part No: 340220031
|
|
|
|
|
Home -> Fishing -> Fishing Accessories -> Rod Holders->Plastic Flush-Mount Rod Holders
These light- to medium-duty rod holders are made of high-impact ABS plastic so you‘ll never have to worry about rust Flange size is 3 1/2" x 4 1/4". Flange has a slightly textured top surface.
Part No: 340220032
|
|
|
|
UV-stabilized polypropylene Mounting hardware is included Single rod, 11 1/4"H x 2 5/8" Diameter.
Part No: 340220072
|
|
|
|
Tube Rod Storage Racks UV-stabilized polypropylene Mounting hardware is included 2-Rod, 11 1/4"W x 11 5/16"H x 2 5/8" Diameter.
Part No: 340220074
|
|
|
|
Tube Rod Storage Racks UV-stabilized polypropylene. Mounting hardware is included.
Part No: 340220076
|
|
|
|
Home -> Engine Systems -> Engine Parts
SELOC Marine tune-up and repair manuals provide the most comprehensive, authoritative information available for outboard, inboard and stern-drive engines, as well as personal watercraft. SELOC has been the leading source of how-to information for the marine industry since 1974. Step-by-step illustrated keyed procedures guide you through every conceivable job possible, including all adjustments necessary. Accurate specifications and wiring diagrams covers all Gasoline Engines and Drive Systems.
Part No: 3404
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Machine Screws - Phillips Flat Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 3404A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Machine Screws - Phillips Oval Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 3405
|
|
|
|
Home -> Engine Systems -> Engine Lubrication -> Oil Change Pumps
Handles many liquid draining and transfer jobs, yet is small enough for a tool or tacklebox. Includes 2" hose and draw tube for draining oil through dipstick tube.
Part No: 34060-0010
|
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Machine Screws - Phillips Oval Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 3406A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Machine Screws - Phillips Pan Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 3408
|
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Machine Screws - Phillips Pan Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 3409C
|
|
|
|
Home -> Sailboat -> Blocks->29mm Carbo AirBlocks®
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.
Part No: 341
|
|
|
|
Home -> Navigation -> Charts & Chart Catalogs -> Canada->Pacific Coast of Canada Charts
Nautical charts show hazards, aids to navigation, features along the shoreline and the seafloor, as well as man-made and natural features of the area. Large-scale insets of the most frequented small craft havens Photographs of the approaches to harbors and channels Important geographic reference points Each chart also contains a narrative with descriptions of navigation aids and dangers, tide and current characteristics, and information on supplies and facilities at anchorages.
Part No: 3410
|
|
|
|
|
Home -> Navigation -> Charts & Chart Catalogs -> Canada->Pacific Coast of Canada Charts
Nautical charts show hazards, aids to navigation, features along the shoreline and the seafloor, as well as man-made and natural features of the area. Large-scale insets of the most frequented small craft havens Photographs of the approaches to harbors and channels Important geographic reference points Each chart also contains a narrative with descriptions of navigation aids and dangers, tide and current characteristics, and information on supplies and facilities at anchorages.
Part No: 3412
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes->Mercury Skeg Anodes
Mercury zinc skeg anodes Short - 2 1/4".
Part No: 34127
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes -> Outboard/Outdrive Anodes->Anode-Mercury Fin
All Mercury anodes conform to Mil-A-24779. Standard Skeg 2 1/4".
Part No: 34127-A
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Easypoxy 1-Part Polyurethane Enamel
.
Part No: 3415-QT
|
|
|
|
|
Home -> Navigation -> Charts & Chart Catalogs -> Canada->Pacific Coast of Canada Charts
Nautical charts show hazards, aids to navigation, features along the shoreline and the seafloor, as well as man-made and natural features of the area. Large-scale insets of the most frequented small craft havens Photographs of the approaches to harbors and channels Important geographic reference points Each chart also contains a narrative with descriptions of navigation aids and dangers, tide and current characteristics, and information on supplies and facilities at anchorages.
Part No: 3419
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Tapping Screws - Slotted Oval Head - Bulk
Type 18-8 stainless steel.
Part No: 342
|
|
|
|
|
Home -> Sailboat -> Blocks -> Blocks->29mm Carbo AirBlocks®
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.
Part No: 342
|
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Machine Screws - Phillips Flat Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 3421
|
|
|
|
Home -> Engine Systems -> Engine Parts
This kit contains points, condenser and rotor for Delco conventional ignition systems.
Part No: 34235Q1
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Square Drive Bits
Driver bits for use with square drive screws.
Part No: 3423E
|
|
|
|
|
Home -> Navigation -> Charts & Chart Catalogs -> Canada->Pacific Coast of Canada Charts
Nautical charts show hazards, aids to navigation, features along the shoreline and the seafloor, as well as man-made and natural features of the area. Large-scale insets of the most frequented small craft havens Photographs of the approaches to harbors and channels Important geographic reference points Each chart also contains a narrative with descriptions of navigation aids and dangers, tide and current characteristics, and information on supplies and facilities at anchorages.
Part No: 3424
|
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Square Drive Bits
Driver bits for use with square drive screws.
Part No: 3424E
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Screw Eyes - Bulk Packs
Type 18-8 stainless steel.
Part No: 3427C
|
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Screw Eyes - Bulk Packs
Type 18-8 stainless steel.
Part No: 3429C
|
|
|
|
|
Home -> Sailboat -> Blocks->29mm Carbo AirBlocks®
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.
Part No: 343
|
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Screw Eyes - Bulk Packs
Type 18-8 stainless steel.
Part No: 3431C
|
|
|
