Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.

Impeller, 18-3062 from SIERRA
Recommended replacement schedule is every 3 years for fresh water and every year for salt water Click to view a Sierra Impeller Application Chart (PDF) For further assistance, have your year & model information handy and call our Product Advisors at 1-800-BOATING.

CARB GASKET KIT from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Yamaha Carb Kit from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Replaces OMC P/N 378444 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

For Chrysler/Force, 89-817109A2 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

1-1/2" Traveler Track End Stop from SCHAEFER
Stop-End Traveler 1. 5in|Stop-End Traveler 1.

Spinnaker Pole Car, Track #2720, 900sq.ft. Max. Sail Area, 1125lb. SWL from HARKEN
Now with captive ball bearings, which eliminates the need for a ball-bearing loader during installation or removal from track. These cars run freely, fit low-beam traveler track and are easy to adjust under any load.

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.

Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .

Hi-Load Ti-Lite Car, Torlon Bearings, 850lb. SWL from HARKEN
These lightweight, solid aluminum and compact captive ball (CB) travelers are built to handle very high loads. Captive ball bearings let you roll the cars on and off the track without using a ball loader. Boat Size: Dinghies, multihulls, to small offshore boats. Material: One-piece solid aluminum . Shackle: Pivoting toggle models—fasten control blocks directly to post without needing a shackle. Sheave: Fixed sheave models—mainsheet loads 40° or less from vertical.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

Rail Mount Outboard Bracket, 10 1/2" from WEST MARINE
Keep your small outboard safe and upright on the stern rail, rather than stowed in a locker where gasoline from the tank could cause hazardous fumes to collect, or spill and ruin stored goods. Two-piece mounting blocks clamp around a 1'' O. D. rail ''T''. Holds outboards up to 8 hp. Each comes complete with stainless mounting bolts. UV-stabilized polypropylene.

PAR-Max 2 Pump Diaphragm Kit from JABSCO
PAR-Max 2 Pump Service Kits.