Flat Cam Riser, 1"H from HARKEN
Harken Cam-Matic cleats are legendary for smooth operation when holding and releasing control lines. Three rows of Delrin ball bearings allow the jaws to open and close smoothly under the highest loads. Light springs allow the cleats to open freely, so the teeth do not have to be sharp which means that your line lasts longer. Use models with aluminum jaws for high loads, or when the line will be drawn through the teeth for adjustment.

Acetal Thru-Transom Scupper from WEST MARINE
One-way rubber flapper valve and thru-hull fitting. For 1-1/2"ID hose. Overall length: 6-1/4". Installation hole size: 2". Max.

Flush Lock - Black/Stainless Steel with Adjustable Offset Cam Bar from PERKO
Black plastic with stainless steel "D" ring handle and with adjustable offset cam bar. Two O-rings for increased water resistance. Position indicator shows open or closed position. Door thickness: 3/8" to 1-14" . Face plate dimensions: 2-7/8" x 2-7/8" . Adjustment latch bar: 3/8" to 3" .

Flush Cup Door Latch from PERKO
Chrome plated zinc alloy with sliding lock button. For door thickness 3/4 to 1-1/8 inches. Supplied with black plastic spacer for surface mounting. Bevel/Strike Type: Regular w/Box. Case Dimensions: 2-1/8 x 1-3/4 .

29mm Carbo Clew Block Assembly from HARKEN
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.

Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.

2-5/8" x 1-1/2" Euro Utility Hinge from WEST MARINE
Stamped utility hinge with 1/2" offset from TACO. Made of marine grade 304 stainless steel with polished finish, non-corrosive utility hinge is ideal for hatches, cabinets, and doors inside and outside the boat. Measures 2-5/8" x 1-1/2" x .

Drain Plug, Bronze 1/2" NPT Threaded from MJS MANUFACTURING
Don’t forget to install your trailerable boat’s drain plug and get that sinking feeling! Get the Plug Boss instead. Put the bright red anodized aluminum plug holder in the most logical place possible, on the trailer winch handle, and never forget to reinstall your drain plug when you launch your boat (or remove it when you haul out). Choose a Plug Boss to fit either the 1" rubber tee handle drain plug or a 1/2" pipe threaded bronze drain plug.

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.

Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .

WL/1 Fairlead Model from SPINLOCK
New low-profile design easily mounts to 1" stanchion using internal clamping system. WL/2 sheave model utilizes unique tracker ball angle adjustment. WL/1 Fairlead model includes stainless-steel bullseye for strength.

1/4" Dia. Stamped Halyard Shackle, 1,000SWL from SCHAEFER
Stamped Halyard Shackles haveflared heads with cross pin retainer for attachment to rope. Captive design prevents accidental opening Quick release pin #93-42 - 1/4" Shackle Pin dia. , 1/2" Inside Width, 1,000 SWL #93-45 - 5/16" Shackle Pin dia.

1-1/2" Traveler Track End Stop from SCHAEFER
Stop-End Traveler 1. 5in|Stop-End Traveler 1.

Replacement Delrin Roller, 2-1/2" Dia., 1-3/4 Width from LEWMAR
Anchor rollers make dropping and weighing anchor easier on you and your boat. They help reduce chafe, prevent scratches and dings to your boat’s finish and provide a secure place to store your anchor when used in conjunction with an optional chain stopper or tensioner. We stock rollers to fit the most common combinations of anchor, mounting style and boat. Installation note: overhanging anchor rollers should be supported along at least 2/3 of their length. Easily installed using common tools.