Top Sellers
Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
|
Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.
|
Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.
|
|
|
Off/1/All/2 Battery Switch, 380 Continuous Amps, 850 Intermittent Amps from PERKO
For high-amperage applications like diesel engine starters, large inverters and windlasses. Reinforced polycarbonate body, 1/2"dia. brass terminal connections and an alternator field disconnect. Alt. Field Disc. : Yes . Switch Material: Reinforced Polycarbonate. Terminal Material/Size: Brass 1/2"dia. . Switch Dimensions: 5-1/4"sq. x 3-3/8"H .
|
SeaStar Helm Seal Kit from TELEFLEX
Replacement shaft seal kit HS5176 fits various post-1990 SeaStar 1. 4, 1. 7 (I), 2. 0, 2. 4 (II), SeaStar Pro and SeaStar helms.
|
12V Reversible Flo-Master Vane Pump from GROCO
Rigid-vane pumps for pumping water, oil or diesel. Positive-displacement pump is self-priming to 2’. Long-lasting, continuous-duty, ignition-protected motor has ball bearings and a #316 stainless-steel shaft Application: General light to intermittent duty utility pumping . Gallons Per Minute: 6. 5 (oil) . Material: Bronze pumphead, stainless shaft . Port Sizes: Male garden hose or 1/2" female NPT inlet & outlet . Dimensions: 3 3/8"H x 4 3/8"W x 7 1/2"L .
|
Electronic Horn, Black from AQUA-SIGNAL
This under-deck hidden horn is designed for vessels under 12 meters, draws less than 1/2 amp and is easily installed in a standard 2 1/4" cutout. Each unit is completely sealed and comes with a waterproof gasket. All openings are sealed to let sound out but prevent water from coming in. Loudness dB: 106-108dB. Design Standards: USCG, CE. Dimensions: 4. 92"L x 3. 11"W x 3. 43"D. Draw: Less than 0. 5A at 12V.
|
1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .
|
Gusher 10 Pump from WHALE PUMPS
Die-cast, epoxy-coated, anodized alloy, synthetic neoprene rubber diaphragm and stainless steel. Removable stainless handle with lanyard. To complete the installation, select either the Aluminum or Plastic Thru-Deck Kit, which seal the installation against water intrusion and and give it a finished look. Nitrile Diaphragm Kit, AK3714, available through special order. Material: Anodized aluminum . Dimensions: 8"H x 4-1/8"W x 5-3/4"L . Port Sizes: 1-1/2" .
|
Acetal Thru-Transom Scupper from WEST MARINE
One-way rubber flapper valve and thru-hull fitting. For 1-1/2"ID hose. Overall length: 6-1/4". Installation hole size: 2". Max.
|
Aft-Deck Shower System from ATTWOOD
This compact hot/cold shower stores neatly in its own compartment on the stern or in the head. Includes a handheld shower spray head with shutoff, 6' hose, hot/cold water controls and a cover. Easily hooked into your freshwater system. Compartment is drilled for six #8 fasteners. Material: High-impact plastic . Dimensions: 9-1/2"H x 5"W x 2-1/4"D . Hose Size: 6'L . Port Sizes: 1/2" NPT .
|
Surface-Mount Titan Bilge Pump from WHALE PUMPS
Powerful, lightweight bilge pump. Constructed entirely from non-corroding materials. The Titan has a quick release clamp for speedy maintenance. The removable handle can be oriented in any direction. Surface mount and thru-deck mount models available. gpm: 28. Material: Plastic. Dimensions: 15-9/16"H x 9-1/4"W x 17-1/4"L. Port Sizes: 1-1/2".
|
Flipper Pump from WHALE PUMPS
Easy back-and-forth action produces one-way discharge. Spout swivels. Made of nylon, aluminum and synthetic rubber. For 1/2"ID hose. Material: Nylon, aluminum, rubber . Capacity: 2gpm . Dimensions: 7-1/8"H x 6"dia. . Cutout Size: 2". Clearance: 4-1/2" .
|
Hatch - Ocean 60 Flat Base from LEWMAR
Well-engineered hatches with CE-certified quality materials and construction. Smoothly styled external hinge enables one-hand operation. Inside handles feature locks that cannot be forced from the outside. Flat base or 1'' flange base (pictured). 3-year warranty. Flat base cutout sizes: Ocean 10 - 10" x 10". Ocean 20 - 7-3/4"W x 13-1/2"L. Ocean 30 - 12-5/8"W x 17-3/4"L. Ocean 40 - 16-3/8" x 16-3/8". Ocean 44 - 17-3/16" x 17-3/16".
|
|
1, 2-1, 2" from LASDROP SHAFT SEALS, 4" from LASDROP SHAFT SEALS, 3-1
|
|
Home -> Engine Systems -> Engine Parts->Water Circulating Pumps
As the originator of the flexible impeller engine cooling pump, Jabsco has a reputation for quality, reliability and serviceability. These pumps can be fully serviced and restored to like-new condition with a simple service kit, thus avoiding costly replacement.
Part No: 42730-0000
|
|
|
|
Home -> Interior, Flags & Gifts -> Folding Bikes & Scooters->CX 21-Speed Cruser
The CX Comfort Bike offers mountain bike performance with an added comfort package built right in to soften the ride. It was made to travel with you anywhere you go. CX Standard Features Full-size bike for cruising city streets and boardwalks with 26" standard wheels. Folds to 36" x 28" x 12" in under thirty seconds without the use of tools. Limited lifetime warranty on frame. Adjustable headset and raised handlebars allow for comfortable seating position.
Part No: 44318
|
|
|
|
Chargers are ignition protected, so they're safe for engine room installation and they feature virtually no F/EMI interference, are AC/DC fuse protected and meet FCC Class B requirements. Allows selection of charging cycles and voltages for lead acid, AGM or gel batteries. These units also act as a power supply providing constant voltage to DC components such as bilge pumps or DC lighting. Automatic Functions: Over-current, thermal & reverse-polarity protection, temperature compensation .
Part No: 93-12305SP-A
|
|
|
|
Home -> Fishing -> Reels->International VSX Series Reels
This premium reel was designed for braided linesFeaturing an improved design over V-series reels, and built specifically to handle braided lines. Powerful double-disc drag with 150-degree drag quadrant is engineered specifically to muscle through extreme drag settings while maintaining an appropriate and smooth drag curve throughout the entire range of the drag lever. Stainless steel main and pinion gears . Drag cam to achieve extreme drag ranges.
Part No: 30VSX
|
|
|
|
Home -> Electrical -> Batteries & Accessories->SeaVolt® Dual-Purpose Absorbed Glass Mat Batteries
AGM batteries are great in both deep cycle and starting applications. They require less charging time than conventional batteries, they have low self-discharge and they're maintenance free—no need to add water. Sealed, valve-regulated design eliminates acid spills & terminal corrosion . Flexible design allows them to be installed in almost any position . Resistant to vibration damage . Rated at 300 cycles . Warranty: 18-months free replacement, 5-year pro-rated warranty.
Part No: 8A4D
|
|
|
|
A stationary carbon flange is held in contact against a stainless flange, which rotates with the prop shaft. The high-density carbon/graphite flange is attached to the boat by a nitrile bellows which, with the help of water pressure, produces a constant pressure between the carbon and stainless flanges. This mechanical seal is impervious to engine motion and vibration, creating a 100% watertight and maintenance-free seal.
|
|
|
|
Home -> Engine Systems -> Trim Tabs & Hydrofoils->PT-130 Power Tilt & Trim
It has 20° of trim and a total of 90° of trim and tilt. Pop up on a plane faster, and achieve better performance underway as load and water conditions change. You get a more stable ride, increased top end speed, and better fuel efficiency. The 6" setback enhances boat stability because the increased clearance enables the prop to get a better “bite” at higher prop settings. Durable 6061 T6 aluminum throughout, a self-contained hydraulic power unit, and 2" dia. of thrust. I.
Part No: 13002
|
|
|
|
|
A stationary carbon flange is held in contact against a stainless flange, which rotates with the prop shaft. The high-density carbon/graphite flange is attached to the boat by a nitrile bellows which, with the help of water pressure, produces a constant pressure between the carbon and stainless flanges. This mechanical seal is impervious to engine motion and vibration, creating a 100% watertight and maintenance-free seal.
Part No: 02-212-312
|
|
|
|
Home -> Electrical -> Chargers & Inverters->2000 SP Series Electronic Chargers with Battery Type Selector Switch
Ignition protected, and the 40A model includes automatic temperature regulation. Restores up to three banks simultaneously. Allows selection of charging cycles and voltages for lead-acid, AGM, or gel batteries. Other features include the ability to act as a power supply, easy-to-read DC ammeter, corrosion-resistant components and housing and heavy-duty heat sink design. Runs cool and quiet, no RFI/EMI interference. All models meet FCC Class B requirements. Dimensions: 10A, 15A & 20A—3.
Part No: 93-12402SP-A
|
|
|
|
Home -> Anchor & Docking -> Anchors->Delta™ Fast-Set Anchors
Easy handling, self-launching design sets fast in any seabed One-piece anchor has very high holding power and structural strength. Balanced to fall unaided from bow rollers, so it’s ideal for use with remotely operated windlasses. Heavy ballast in the toe section ensures that the anchor will engage the seabed upon hitting bottom. Lifetime warranty against breakage. Style: Non-Hinged Plow. Material: Galvanized-manganese steel or stainless steel. Application: All bottoms .
Part No: 0057306
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-214-312
|
|
|
|
Home -> Engine Systems -> Trim Tabs & Hydrofoils
**Motor-Trim|**Motor-Trim.
Part No: 18-6798
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-214-234
|
|
|
|
Home -> Anchor & Docking -> Fenders & Docking->P500 Ice Eaters
The P500 de-ices diameter of approximately 40 feet Prevent damaging ice formation around your boat’s hull with a 1/2 hp energy efficient Ice Eater. Motor is matched with a permanent-split capacitor to ensure quick, high-torque and smooth operation from the single-phase induction motor. Copper, stator motor windings are double-insulated, to guard against water. Internal, hard-faced mechanical seal is itself immersed in dielectric lubricating fluid and protects the motor against water intrusion.
Part No: P500/230/100/30
|
|
|
|
|
Home -> Anchor & Docking -> Fenders & Docking->P500 Ice Eaters
The P500 de-ices diameter of approximately 40 feet Prevent damaging ice formation around your boat’s hull with a 1/2 hp energy efficient Ice Eater. Motor is matched with a permanent-split capacitor to ensure quick, high-torque and smooth operation from the single-phase induction motor. Copper, stator motor windings are double-insulated, to guard against water. Internal, hard-faced mechanical seal is itself immersed in dielectric lubricating fluid and protects the motor against water intrusion.
Part No: P500/115/100/30
|
|
|
|
|
Home -> Engine Systems -> Engine Parts
**Alternator|**Alternator.
Part No: 18-5943
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-214-314
|
|
|
|
|
Home -> Engine Systems -> Engine Parts -> Tune Up Parts
**Cylinder Head Assy|**Cylinder Head Assy.
Part No: 18-4491
|
|
|
|
|
Home -> Engine Systems -> Engine Parts
**Distributor|**Distributor.
Part No: 18-5481
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-214-278
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-214-334
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Gen II Shaft Seal
The Gen II offers exclusive features that make it the premier shaft seal on the market. The Friction Ring assembly is mounted with a rigid connection hose and uses a carbon graphite sealing surface all encased by a durable copolymer housing. Built into the friction ring assembly is a cutlass bearing to ensure proper and constant alignment to the shaft. The Clamp/Pressure Assembly secures the assembly around the shaft, preventing the galling or damage to the shaft that can occur with setscrews.
Part No: G-214-3
|
|
|
|
Home -> Sailboat -> Traveler, Tracks & Vang->Traveler Kits
These kits take the confusion out of installing a traveler. Includes components for the most popular Small Boat and Midrange traveler configurations. Kit contains a car, control blocks for the car, and control blocks for the track ends. Small Boat Traveler Kit: Includes 2743 double-cheek blocks, 348 single-fixed blocks on 2735 car with pivot toggle. Midrange Boat Traveler Kit: Includes 1627 car, two 1633 double0sheave end controls with Carbo-Cam cleats, two 342 double-swivel blocks.
Part No: 1630
|
|
|
|
Home -> Anchor & Docking -> Fenders & Docking->Oil-Free D-Icer™
The first affordable oil-free de-icers The new oil-free motors are more energy efficient and save money when used for aeration or de-icing. It is a powerful submersible motor-driven water circulation unit that prevents ice formation during winter months by continuously propelling warmer subsurface water up to the surface. The unique one-piece design of the shroud prevents large debris from being sucked through and damaging the propeller, a major cause of failure in other ice prevention devices.
Part No: 6210D
|
|
|
|
Home -> Engine Systems -> Engine Parts
Electric Start Kit also requires a tiller handle harness & start button or remote control harness assembly.
Part No: 856555A1
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains
**Shaft-Drive|**Shaft-Drive.
Part No: 18-1721
|
|
|
|
Home -> Cabinet & Deck Hardware -> Hatches & Ports->Low-Profile Hatches
Now Lewmar has created a two-piece frame with tough, gray acrylic that can be replaced simply by unscrewing the frame and inserting the new lens. The seal and acrylic are fitted into the aluminum frame to produce a stronger, more leak-proof hatch. All hatches feature a vent position, flange base and sizes 30 and larger have lockable internal and external handles for added security. CE Area II approved. Low-profile hatches have 8mm acrylic in sizes 00 through 54, and 10mm acrylic in size 60.
Part No: 39922030
|
|
|
|
Home -> Electronics -> Global Positioning Systems->GPSMAP® 431/431s
It’s ready to go with a built-in, satellite-enhanced basemap preloaded with U. Inland Lakes and an easy-to-use interface designed to help you navigate the open waters with ease. The GPSMAP 431 also accepts BlueChart® g2 Vision cards for added features and functionality such as high-resolution satellite imagery, 3D views and Auto Guidance technology. Inland Lake map data. For areas outside the U. , the GPSMAP 431 has a worldwide basemap with satellite images in place of more traditional maps.
Part No: 010-00765-00
|
|
|
|
Home -> Electronics -> Fishfinders -> Fishfinders->HDS-5x Fishfinders
High-resolution 480x480 multifunction fishfinder with 5" display offers the same advanced fishfinding capabilities as other combo units without the GPS receiver and chartplotter capability. Offers a 120° view of fish- and structure-finding coverage, plus improved target definition and separation.
Part No: 000-0140-27
|
|
|
|
Home -> Fishing -> Reels->International V Series Lever Drag Reels
The International® V reels offer the most advanced and reliable fish-fighting performance in the world, with an ergonomically designed, contoured, one-piece machined frame, and unbelievable cranking power and strength. Shift: Penn’s Quick Shift engages automatically with a deliberate bump of the shift button (low-speed) or spin of the shift knob (high-speed). This is the easiest, and most angler-friendly two-speed feature on the market, and can be perfomed without letting go of the handle. .
Part No: 50VW
|
|
|
