Replacement Ball Bearings for 150 Cam Cleat from HARKEN
Harken Cam-Matic cleats are legendary for smooth operation when holding and releasing control lines. Three rows of Delrin ball bearings allow the jaws to open and close smoothly under the highest loads. Light springs allow the cleats to open freely, so the teeth do not have to be sharp which means that your line lasts longer. Use models with aluminum jaws for high loads, or when the line will be drawn through the teeth for adjustment.

CARB GASKET KIT from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Yamaha Carb Kit from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Spinnaker Pole Car, Track #2720, 900sq.ft. Max. Sail Area, 1125lb. SWL from HARKEN
Now with captive ball bearings, which eliminates the need for a ball-bearing loader during installation or removal from track. These cars run freely, fit low-beam traveler track and are easy to adjust under any load.

Delrin Sheave, 1/2" Max. Line Dia., 1-7/16" OD, 3/8" ID, 5/8" Width from SCHAEFER
Schaefer sheaves are designed to be compatible with Schaefer products, and are not intended for use in other manufacturer's blocks. Delrin sheaves are injection molded with UV inhibitors and monitored molding cycles for a stronger product.

Replaces OMC P/N 378444 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Impeller, 18-3062 from SIERRA
Recommended replacement schedule is every 3 years for fresh water and every year for salt water Click to view a Sierra Impeller Application Chart (PDF) For further assistance, have your year & model information handy and call our Product Advisors at 1-800-BOATING.

For Chrysler/Force, 89-817109A2 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Flat Cam Riser, 1"H from HARKEN
Harken Cam-Matic cleats are legendary for smooth operation when holding and releasing control lines. Three rows of Delrin ball bearings allow the jaws to open and close smoothly under the highest loads. Light springs allow the cleats to open freely, so the teeth do not have to be sharp which means that your line lasts longer. Use models with aluminum jaws for high loads, or when the line will be drawn through the teeth for adjustment.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

300 Series Fairlead Block, Fixed Style, 2-7/32" x 3/4" from SCHAEFER
Same as the Schaefer 200 Series fairlead blocks, but with twice the working load. Use #10 fasteners. Configuration: Lead block. Sheave: UV-stabilized white Delrin®. Ball Bearings: Delrin. Sheave Size: 1-7/16" (37mm). Line Diameter: 7/16". Cheek Material/Finish: Polished stainless.

Hi-Load Ti-Lite Car, Torlon Bearings, 850lb. SWL from HARKEN
These lightweight, solid aluminum and compact captive ball (CB) travelers are built to handle very high loads. Captive ball bearings let you roll the cars on and off the track without using a ball loader. Boat Size: Dinghies, multihulls, to small offshore boats. Material: One-piece solid aluminum . Shackle: Pivoting toggle models—fasten control blocks directly to post without needing a shackle. Sheave: Fixed sheave models—mainsheet loads 40° or less from vertical.

29mm Carbo Clew Block Assembly from HARKEN
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.

Snap Furl CF-700 Furling System from SCHAEFER
" Small boat furler comparison, Practical SailorSnapFurl systems come in two sizes to accommodate boats 16' to 24' and boats 24' to 28' and represents the latest in quality Schaefer design and engineering. The efficient Round Geon™ PVC foil snaps quickly and easily around your boat’s existing headstay without the need for special tools or modifications to the rig. System SnapFurl CF-500 for Boats 16’ to 24’ (4. Long fiber reinforced injection molded components make SnapFurl CF 500 unique.

RigTune Pro Digital Rig Tension Gauge from HARKEN
Old-fashioned spring gauges, like the Loos Pro, don’t provide repeatable numbers. This product does. Unlike spring-loaded gauges, the Harken Rigtune Pro measures rig tension to the nearest kilogram. A load cell records the pressure on one of the pins and the measurement is displayed on a simple, easy-to-read screen. The Rigtune Pro fits a specific range of rigging sizes, 2. As rigging is deflected over three pins on the back of the gauge, a load cell records the pressure on one of the pins.