CARB GASKET KIT from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Yamaha Carb Kit from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Replaces OMC P/N 378444 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Impeller, 18-3062 from SIERRA
Recommended replacement schedule is every 3 years for fresh water and every year for salt water Click to view a Sierra Impeller Application Chart (PDF) For further assistance, have your year & model information handy and call our Product Advisors at 1-800-BOATING.

For Chrysler/Force, 89-817109A2 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Sierra-Tube-Exhaust from SIERRA
Some larger V-8 engines that create a large amount of back pressure use exhaust tubes rather than bellows. This helps to relieve the excessive pressure and eliminate problems with premature bellows failure. In the past, the exhaust bellows would blow up like a balloon and cause the drive shaft bellows to rub against the yoke and U-joints causing holes in the bellows.

10 Micron Replacement Filter Element for OMC 502905 from SIERRA
High-performance fuel injected engines require ultimate fuel filtration, separation of water from the fuel supply and maximum fuel flow. Sierra’s new filter elements deliver all three of these critical performance factors. 7900-Series 10 micron filters eliminate harmful contaminants at over 90% efficiency, while removing over 99% of emulsified water. Today’s ethanol-blended fuels increase the chances of water in fuel tanks, resulting in premature wear, poor performance and component damage.

Water Circulating Pump - #18-3581 - Chrysler Inbd # 3004886, 3619542, 3619859, 3745985 from SIERRA
Water Pumps The water pump is the heart of your inboard or I/O cooling system. All Sierra pumps are bidirectional and can be installed on reverse rotation engines. The pumps are also powder coated for additional protection. Includes mounting gasket. Pumps include brass bi-directional impellers, brass plugs and fittings, carbon resin seal, all mounting gaskets, stainless steel seal cup and spring, stainless steel back plate (where required), and powder coating for maximum corrosion protection.

Johnson/Evinrude Outboard Starter, 120 to 140hp V4 (1985-99), 10 tooth drive gear from SIERRA
Sierra's new and remanufactured starters are the only marine starters that meet Marine UL standards. Sierra's remanufactured starters all have new solenoids, drives, bushings, brushes and springs. The bodies are powder coated for greater corrosion resistance. Sierra has entered an agreement with United Technologies to market their complete line of outboard starters and components. All are 100% load tested . Our remanufactured starters are covered by Sierra's customer satisfaction warranty .

30GPH Cartridge, Replaces Racor S3240 from SIERRA
High-performance fuel injected engines require ultimate fuel filtration, separation of water from the fuel supply and maximum fuel flow. Sierra’s filter elements deliver all three of these critical performance factors. 7900-Series 10 micron filters eliminate harmful contaminants at over 90% efficiency, while removing over 98. They’re engineered for today’s sterndrives and inboards, along with 2-cycle and 4-cycle outboards. That is why a high efficiency water separating filter is so important.

60GPH Cartridge, Replaces Racor S3227 from SIERRA
High-performance fuel injected engines require ultimate fuel filtration, separation of water from the fuel supply and maximum fuel flow. Sierra’s filter elements deliver all three of these critical performance factors. 7900-Series 10 micron filters eliminate harmful contaminants at over 90% efficiency, while removing over 98. They’re engineered for today’s sterndrives and inboards, along with 2-cycle and 4-cycle outboards. That is why a high efficiency water separating filter is so important.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

Snap Furl CF-700 Furling System from SCHAEFER
" Small boat furler comparison, Practical SailorSnapFurl systems come in two sizes to accommodate boats 16' to 24' and boats 24' to 28' and represents the latest in quality Schaefer design and engineering. The efficient Round Geon™ PVC foil snaps quickly and easily around your boat’s existing headstay without the need for special tools or modifications to the rig. System SnapFurl CF-500 for Boats 16’ to 24’ (4. Long fiber reinforced injection molded components make SnapFurl CF 500 unique.

Hi-Load Ti-Lite Car, Torlon Bearings, 850lb. SWL from HARKEN
These lightweight, solid aluminum and compact captive ball (CB) travelers are built to handle very high loads. Captive ball bearings let you roll the cars on and off the track without using a ball loader. Boat Size: Dinghies, multihulls, to small offshore boats. Material: One-piece solid aluminum . Shackle: Pivoting toggle models—fasten control blocks directly to post without needing a shackle. Sheave: Fixed sheave models—mainsheet loads 40° or less from vertical.

Small Bronze Ball Valves with Brass Ball, 3/8" NPT from APOLLO
Free-floating, chrome-plated brass ball. NPT threads. Stainlesssteel handle. Note: These are for inline, non-saltwater applications.