Top Sellers
2-5/8" x 1-1/2" Euro Utility Hinge from WEST MARINE
Stamped utility hinge with 1/2" offset from TACO. Made of marine grade 304 stainless steel with polished finish, non-corrosive utility hinge is ideal for hatches, cabinets, and doors inside and outside the boat. Measures 2-5/8" x 1-1/2" x .
|
1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .
|
Hose Adapter, From 1-1/8" to 3/4"-5/8" from RULE INDUSTRIES
#69 is stepped & adapts from 1-1/8" to 3/4" - 5/8" #57 is an elbow & adapts from 1-1/8" to 1" NPT #67 adapts from 1-1/2" to 1-1/8".
|
1-7/8" Brass Standard Hasp from ABI
Highly polished brass . Fixed eye (does not swivel). 1"w x 1-7/8"L. Padlock hole diameter 5/16" .
|
Teak Plugs - 3/8" from SEAFIT
Use these teak plugs to cover screw heads or fill small holes for a beautiful smooth finish to your installation. Sizes: 1/4" 5/8" 5/16" 3/8" 1/2" 1".
|
Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.
|
Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
|
Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.
|
Deck Fill, Gas, w/Key, 1-1/2" from WHITECAP INDUSTRIES
Stainless-steel deck fills with durable cast heads—not the thin stamped heads found on many imports. Gas, Diesel and Water fills have 1 1/2" openings. Waste fill has 2" opening. All connect to 1 1/2" hose, and include a stainless key. Material: Stainless . Attachment Method: 1 1/2" hose . Flange Diameter: 3" or 3 1/2" (waste) . Fasteners: Three #10 FHMS . Cutout Diameter: 1 5/8" .
|
Drain Plug, Bronze 1/2" NPT Threaded from MJS MANUFACTURING
Don’t forget to install your trailerable boat’s drain plug and get that sinking feeling! Get the Plug Boss instead. Put the bright red anodized aluminum plug holder in the most logical place possible, on the trailer winch handle, and never forget to reinstall your drain plug when you launch your boat (or remove it when you haul out). Choose a Plug Boss to fit either the 1" rubber tee handle drain plug or a 1/2" pipe threaded bronze drain plug.
|
Replacement Delrin Roller, 2-1/2" Dia., 1-3/4 Width from LEWMAR
Anchor rollers make dropping and weighing anchor easier on you and your boat. They help reduce chafe, prevent scratches and dings to your boat’s finish and provide a secure place to store your anchor when used in conjunction with an optional chain stopper or tensioner. We stock rollers to fit the most common combinations of anchor, mounting style and boat. Installation note: overhanging anchor rollers should be supported along at least 2/3 of their length. Easily installed using common tools.
|
Compressor Cooler 33qt. AC/DC from DOMETIC ENVIRONMENTAL
Introducing the Coolmatic® CF Series. These units offer ample storage for refrigerated and frozen foods, as well as many technical extras and problem-free operation from all on-board and AC adapter systems High-Impact Engineered Polymer Cabinet will not Dent or Rust Two-Tone Gray Housing Matches Most Automotive Interiors Top Lid Locks, Detaches and Folds Up Carrying Handle or Carrying Grip for Easy Transport Removable Coated Wire Basket Resists Freezing (not included on the CF18 or CF-35.
|
Gunnel Guard - 1/2" Round, 1-1/2" Diameter, 20' Length from TAYLOR
These polyester-covered guards will protect your boat from dings and scratches and they won’t rot in the sun or saltwater like cotton guards. Great for use on dinghies and swim platforms, too. Fabric tabs attach easily with screws or nails. Half Round is for flat surfaces; 3/4 Round is for 90° edges. Sold in 10' or 20' lengths or by the foot up to 50'. Material: Polyester fabric/closed-cell foam . Attachment Method: Screws or nails . Shock Absorption Mechanism: Foam padding .
|
|
|
Fiberglass Boat Cleaner 920 1/2 Gallon from COLLINITE
Removes rust, exhaust, oil, grease, and oxidation stains from fiberglass. Restores the original color quickly without hard rubbing or buffing, leaves a chemically clean surface to which waxes can bond. Use with fiberglass boat wax or heavy-duty paste Fleetwax . Made in U. S. A.
|
|
1, 2, 8, 1 Power Ratio 1st, 52qt from DOMETIC ENVIRONMENTAL
|
|
Home -> Anchor & Docking -> Ladders, Ramps & Boat Hooks->Gale Sail
The safest and easiest way to hoist a storm jib in heavy conditions. Simply furl the genoa sheets down to the deck and yank the Gale Sail over the furled headsail, attach its sheets and hoist it with a spare halyard or the spinnaker halyard. Eliminates the need for a removable headstay. No need to unfurl, lower and pack the genoa to hoist the storm jib. The Gale Sail is a heavy-duty storm jib that can be flown either by itself, or in combination with the reefed mainsail or trysail.
Part No: GS100
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Dry-Seal Shaft Seal
As in all Lasdrop seals, the unit incorporates a cutlass bearing in the housing to keep the unit properly aligned with the shaft. Available in shaft sizes 3/4" to 8", accommodating any size stern tube up to 10-1/2" in diameter. Metric sizes available. Also an excellent rudder shaft seal. Seal housing constructed of a durable copolymer with built in cutlass bearing ensuring proper alignment to the shaft. Optional Back-up seal rotates with the shaft until replacement is needed.
Part No: D-400-5
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Dry-Seal Shaft Seal
As in all Lasdrop seals, the unit incorporates a cutlass bearing in the housing to keep the unit properly aligned with the shaft. Available in shaft sizes 3/4" to 8", accommodating any size stern tube up to 10-1/2" in diameter. Metric sizes available. Also an excellent rudder shaft seal. Seal housing constructed of a durable copolymer with built in cutlass bearing ensuring proper alignment to the shaft. Optional Back-up seal rotates with the shaft until replacement is needed.
Part No: D-400-6
|
|
|
|
Home -> Electrical -> Meters & Distribution -> Distribution Panels->120V A-Series Source Selection Toggle Circuit Breaker Panels
Blue Sea Systems designs innovative, reliable, superior quality electrical system products. Blue Sea Systems products are tested aboard the company's boat to ensure reliability and ease of use in real world conditions. This results in the delivery of innovative, reliable electrical products that exceed the quality standards of other companies. Blue Sea Systems' in-house lab is used to load test and thermal test products to ensure they will perform under marine conditions. Digital Multimeter.
Part No: 8494
|
|
|
|
Home -> Seating & Covers -> Seating
Built-in backrest and four rod holders makes this leaning post a great addition to your center-console boat, turning it into a ready-to-go, just add rods, fishing machine. Space saving design features sturdy 1 1/2" anodized aluminum tubing plus high-density, contoured, cushioned seat and backrest for comfortable seating. There’s even room for a 72qt. cooler underneath.
Part No: BM1012-710
|
|
|
|
Home -> Cabin & Galley -> Refrigeration & Coolers -> Refrigeration Conversion
Air-cooled Danfoss BD50F high-efficiency compressor for temperate climates. Extremely quiet running . Compressor is shrouded for maximum fan-forced cooling efficiency . Long-lasting stainless steel construction . Features make installation easy . Quick-disconnect couplings . Built-in troubleshooting diagnostics . Modular phone jack thermostat/electronics connections . Amp Draw: 4. 5A–5. 5A@12V DC while on .
Part No: CU-100
|
|
|
|
Home -> Fishing -> Trolling Motors->Tour Series Digital Motors
Trolling motors with digital speed controlThese motors feature Digital Guardian speed control, stainless steel shafts, all metal heads and foot pedals, and rock solid adjustable Pull/Pull steering that limits torque and fatigue. The sealed on-off switch offers unmatched durability while the Soft Start feature smoothes initial acceleration at high speed settings.
Part No: 9BT42GAAF
|
|
|
|
Coolmatic RD series refrigerators are a terrific value. They operate using a Danfoss BD35F compressor, which lends the following: steady, quiet-running operation with minimum power consumption. Operates on either 12V DC or 24V DC, with automatic switchover. Switches over to 115V AC when 12V/24V DC is unavailable. Door mounts on left or right, for installation flexibility . >Door locks at both top and bottom, to secure contents . Additional features include spacious freezer compartments .
Part No: RSD-1115U/F
|
|
|
|
Home -> Sailboat -> Winches->Two-Speed Self-Tailing Winches
More bearings and pawls combined with Italian styling—better form and function Harken’s precision winches are extremely reliable and exceptionally efficient. Built to very fine tolerances, these winches feature large roller bearings on most gears and drive shafts. Use single-speed winches for sheets on small boats and for halyards on medium and large boats. Use small two-speed winches for sheets and halyards on boats of all sizes. Winches as small as the 48 have roller bearings in every gear.
Part No: B32.2STA
|
|
|
|
Home -> Anchor & Docking -> Fenders & Docking->Freedom Fenders™
Made from the highest quality, military-grade PVC material, these fenders are built to last in the marine environment. Unique V shape keeps them on pilings no matter which way the boat moves. Seams are heat and pressure welded. Easily inflate through a locking valve and can hang horizontally or vertically. Deflate quickly and roll up for easy stowage. One-year warranty. Freedom Fenders for Boats to 70' LOA Same as above with unique V shape and rotationally molded, heavy-gauge PVC material.
Part No: FF5825B
|
|
|
|
Home -> Electrical -> Chargers & Inverters->Alternator/Regulator Packages
Alternator/regulator/temp sensor packages pre-matched to your engine! Save money and avoid guesswork with a pre-matched combination of high-output alternator, smart multi-stage ARS-5 regulator and temperature sensing module to match your Yanmar, Volvo or Atomic 4 engine. The YP-70 package (for 2- or 3-Series Yanmar engines) features Balmar's Smart Ready internally regulated Model 60-70-SR-IG alternator, advanced ARS-5 regulator with wiring harness and MC-TS-A alternator temperature sensor.
Part No: 60YP100SRKIT
|
|
|
|
Home -> Cabin & Galley -> Stoves & Propane System -> Propane Systems->Marine LP Cylinder Locker
Built to ABYC specifications. High-quality fiberglass construction. Fully assenbled with leak-tested ABYC regulator with gauge, 12V DC low presssure brass solenoid, gas control panel, straight-through fittings for solenoid wiring and L. P. gas supply hose and a thru-hull fitting for bottom vent. Also fitted with stainless-steel hinges, chromed-brass, quick-release hatches, rubber gasket and screw-down cylinder clamp. The singe 10lb. units hold steel or aluminum tanks. The single 11lb.
Part No: 1502-0020
|
|
|
|
Home -> Fishing -> Trolling Motors->Riptide Saltwater Bow-Mount Trolling Motors
Riptide trolling motors Riptide motors are built saltwater tough, with premium-grade marine alloys, including aluminum upper arms that are impervious to rust. Variable speed models feature Maximizer technology that provides up to five times longer run time on a single charge. Bow Mounts: Latch and Door—New compact mount is engineered for today's popular technical skiffs and "flats" boats. BowGuard 360—breaks away on impact from any direction, then automatically resets itself.
Part No: 1363500
|
|
|
|
Detachable cooling unit with 5‘ supply line, fully hermetic Danfoss BD35F compressor with integrated control electronics, low-voltage protection for consumer or starter battery, electronic fuse/automatic reverse pole protection, dynamically ventilated lamellar condenser, aluminum rollbond evaporator, mechanic, continuously variable thermostat. 3. 94 cubic feet . 12/24 volts DC . 45 watts . 52 lbs . 20. 5” W x 29. 12”H x 22”D . CFC-free polyurethane insulation.
Part No: RSD-0115U
|
|
|
|
Home -> Fishing -> Fishing Accessories
Keeps tuna calm and alive longer! Tubes feature quick disconnect mounting brackets, for transom mounting are anodized then white powder coated for long life. Small transom mount nuts mount to transom, tuna tube brackets clip to nuts. Double's are 2 sets of brackets mounted together, only require 4 mounting nuts on transom. This Tuna Tube is white on the outside and black on the inside . Tube inside diameter is 8" x 26" long and will hold a tuna up to 20 pounds.
Part No: PFTT-80-2
|
|
|
|
Home -> Watersports -> Wakeboards, Kneeboards, Skis & Towables->Aqua Jump Trampolines
Enjoy big-bounce performance on any of these sturdy, inflatable trampolines. With a variety of size options you’re sure to find one that’s perfect for your spot on the water. Great for lakes and calm waters. 1000 denier PVC with heat-welded seams and includes a ladder for climbing aboard after a quick plunge. Aqua Jump Jr. accommodates one person under 120lbs. . Available in four sizes: Jumpers Jumping Surface Water Depth Required Height Aqua Jump Jr 1 Child 6.
Part No: 2010
|
|
|
|
Home -> Cabinet & Deck Hardware -> Hatches & Ports->Ocean Series Hatches
Well-engineered hatches with CE-certified quality materials and construction. Smoothly styled external hinge enables one-hand operation. Inside handles feature locks that cannot be forced from the outside. Flat base or 1'' flange base (pictured). 3-year warranty. Flat base cutout sizes: Ocean 10 - 10" x 10". Ocean 20 - 7-3/4"W x 13-1/2"L. Ocean 30 - 12-5/8"W x 17-3/4"L. Ocean 40 - 16-3/8" x 16-3/8". Ocean 44 - 17-3/16" x 17-3/16".
Part No: 39670050
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights->LED Navigation Lights
Lopolights are available for boats up to 164' (50m). Each light is individually tested and certified, concluding with a 36-hour Reliability Stress Screening so you can just install it and forget it! Why should you buy Lopolights? • Completely waterproof (rated IP68+ submersible): Interior is fully filled and sealed with special epoxy resin. • Rated for over 50,000 hours of operation. Not damaged by vibration. • Low power consumption: Less than 30% of the draw of a standard incandescent lamp.
Part No: 200-011
|
|
|
|
Home -> Cabin & Galley -> Refrigeration & Coolers -> Coolers & Ice Chests
Fully hermetic Danfoss BD35F compressor with integrated control electronics, low-voltage protection adjustable for consumer or starter battery by means of a slide switch, electronic fuse/automatic reverse pole protection, dynamically ventilated wire condenser, aluminum rollbond evaporator. 52 quarts . 45 watts . +50°F to 0°F, adjustable via electronic thermostat with LED indicator . 44lbs. CFC-free polyurethane foam . DC connection cables, coated wire basket, detachable carrying handles .
Part No: CF-050DC
|
|
|
|
Home -> Engine Systems -> Engine Lubrication
**Oil-10W30 55 Gal|**Oil-10W30 55 Gal.
Part No: 18-9420-7
|
|
|
|
Home -> Sailboat -> Winches->Ocean Series One- & Two-Speed Self-Tailing Winches
Advanced technology and innovative features has made Ocean Series the world’s most popular winches. Racing sailors appreciate the smooth operation and flawless performance. Fewer moving parts means fewer problems and simpler maintenance. And Ocean’s unique grip pattern makes rope handling easy—easier still with a self-tailing model, which incorporates Lewmar’s Wavespring feature, a combination of the gentle Wavegrip and self-adjusting springs to handle today’s smaller diameter ropes.
Part No: 49030001
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Headsail Furling->FX Code Zero & Gennaker Furlers
Easily furl your Gennaker or Code Zero Innovative continuous line furling systems make code zero and gennaker deployment and dousing extremely easy. These ultralight and compact furlers are easy to install and store and are also only half the weight of a standard gennaker furler. The flat drum functions like a sheave to eliminate the hassle of furling line overrides. Optional blocks (offered below) create a 2:1 mechanical advantage when hoisting. Drum material: Anodized CNC machined aluminum.
Part No: 43110701540
|
|
|
|
Home -> Sailboat -> Headsail Furling -> Furling Accessories->Code Zero Furler Accessories
Code Zero Furler Accessories.
Part No: 3108
|
|
|
|
|
Home -> Engine Systems -> Engine Parts
**Seal-Lower Gearcase|**Seal-Lower Gearcase.
Part No: 18-2368
|
|
|
|
Home -> Watersports -> Wakeboards, Kneeboards, Skis & Towables -> Towables
The Island Hopper™ "Bounce-N-Splash" water bouncer was designed to offer recreational users the same high quality designs and materials used in water trampolines at camps and resorts. The springless, interlaced nylon webbing "bouncer" design uses tube flex features to give you an enjoyable "bouncer" lift with a sturdy trampoline feel. 6 anchor-tie-D-rings (3 inside and 3 under tube) for safe and secure Mooring . 3 swimming assist handles .
Part No: 13bsplash
|
|
|
|
Home -> Electronics -> Global Positioning Systems->GPSMAP® 525, 535 and 545 Color GPS Chartplotters with Built-In Maps
The high-resolution, super-bright, video-quality 5" VGA displays on these chartplotters let you see it all in pristine clarity. Plug an optional BlueChart g2 Vision card into the SD slot to view an extensive aerial photo reference that shows harbors, boat slips and other significant landmarks in graphic detail. The 525 has a worldwide satellite basemap. The 535 is preloaded with inland lake maps and the 545 is preloaded with U. S. Purchase additional regions on BlueChart g2 Vision cards.
Part No: 010-00599-00
|
|
|
|
Home -> Electronics -> Global Positioning Systems->A50 5" Chartplotter
The A50 GPS-Chartplotter is powerful navigation system that combines a direct sunlight viewable high resolution 5” VGA color display with advanced chartplotting. waters and the Great Lakes. Expand your chartplotters capability by adding optional Navionics Gold or HotMaps charts using the onboard CompactFlash card reader. Or step up to Navionics Platinum for the ultimate chartplotting experience. The A50 comes with an innovative tilt and swivel bracket featuring a quick release lever.
Part No: E62184
|
|
|
|
Home -> Electrical -> Chargers & Inverters->Polycrystalline Solar Panels
It’s tough, quiet and consistently converts sun power into electricity to power your onboard electronics. High-efficiency polycrystalline cells convert sunlight to electricity quietly, without pollution or greenhouse gases, day after day, season after season. Using breakthrough technology perfected by Sharp’s nearly 45 years of research, these panels use a textured cell surface to reduce reflection of sunlight, and BSF (Black Surface Field) structure to improve conversion efficiency.
Part No: 135123SH
|
|
|
|
Home -> Anchor & Docking -> Anchors->Manson Ray Anchors
Practical Sailor Best Choice among Heavyweight Anchors Anchors for the biggest, finest boats Designed for larger boats, Ray anchors are Lloyd’s certified as high-holding power anchors and are forged, not cast, for consistent quality of steel and measurements. Ray anchors are trusted to secure some of most famous ships including the world’s largest sloop, the Mirabella V. ) Pros: High holding (Lloyd's-certified) for larger boats to megayachts and ships. Forged—not cast—for quality; sets quickly.
Part No: RAY20
|
|
|
|
Home -> Electronics -> Global Positioning Systems->GPSMAP® 536/536s
The GPSMAP 536 is a compact chartplotter that features a high-resolution, super-bright 5” VGA color display along with an improved high-speed digital design for increased map drawing and panning speeds. It’s ready to go with a built-in, satellite-enhanced basemap preloaded with U. Inland Lakes and an easy-to-use interface designed to help you navigate the open waters with ease. Navigate the Lake The GPSMAP 536 comes ready to go with preloaded U. Inland Lake map data. For areas outside the U.
Part No: 010-00773-00
|
|
|
