Top Sellers
Zinc Grouper Anode from CANADA METALS
Supplements your boat's existing anodes An excellent anodic device to supplement a vessel’s existing anode system, especially to counteract stray current from defective shore power. Clip to bolt on outdrive. Clip to grounding strap if possible or wire items together with copper wire and clip to wire. Do not connect to negative battery terminals. Dimensions: 8 1/4"L x 3 1/4"W x 1 3/8"D.
|
Brass-Bristle Brush from SEAFIT
Solid brass bristles won't rust or corrodeLarge, plastic utility brush has solid brass bristles that won’t rust or corrode. Brass bristles are slightly softer than stainless steel and are therefore less intrusive to surfaces. Molded plastic handle provides solid, controlled grip. Bristles: 5/8"D. Overall length: 8 1/2". Molded plastic handle provides solid, controlled grip. 5/8"L bristles.
|
Solid Brass Vertical Action Galley Pump from FYNSPRAY
Vertical plunger pump with a gracefully arched spout. 50 strokes per gallon. 1"diameter tube. Fits 1/2"–5/8" hose. Requires 8 1/2" clearance below counter surface; 9 3/4" above Material: Brass. Capacity: 50 strokes/gal. Dimensions: 9 3/4"H. Cutout Size: 1 1/8". Clearance: 8 1/2".
|
7' Ugly Stik Combo, Saltwater Spinning; 4.6:1 Gear Ratio; Medium Action from SHAKESPEARE
Shakespeare's versatile Ugly Stik combos give the anger plenty of casting power to deliver bait to crafty and boat-wary fish. The two piece rods feature Fuji reel seats and EVA grips to maximize sensitivity and response to light strikes and the Shakespeare spinning reel sports stainless bearings, graphite frame, and aluminum spools for fast, smooth retrieval and reliable casts. Style: Saltwater Spinning . Target Species: Big Water/Light Tackle Targets . Rod Type: Conventional Ugly Stik .
|
Rounded Oval, 8-1/2"W x 11-1/4"L x 5-1/4"D, 1" Flange, 1-1/2" Drain from AMBASSADOR MARINE
Made from 304 stainless steel and mirror-polished to a deep luster, these sinks incorporate SoundKOTE Noise Reduction Technology to reduce the unpleasant clanging associated with many metal sinks. Flanges permit over- or under-the-counter mounting. Low-Profile 90° drains fit standard 1"ID hose and are slanted to maximize drainage.
|
Step Pad, 10-3/4" x 5-1/4", Blue from LEWMAR
Maintain your footing under all conditions! Self-adhesive, diamond-patterned, nonskid pads are great for decks, steps, dinghy floors, personal watercraft, etc. They resist wear and tear, peeling, saltwater, fuels and chemicals. Pads have rounded edges and are precut to fit most common step sizes. Trim with scissors for a custom fit. Peel-and-stick installation. Sold in pairs.
|
8-1/2" Hatch Holder, Adjustable, for Hatches to 10lb. from MOONLITE MARINE
Stainless, spring-type holders “pop” into place to hold hatches, doors, table leaves, etc. Easy to install. Adjustable model allows opening between 10° and 80°.
|
Large Funnel - 5GPM, 10"H x 8-1/2"Dia., 100 Micron from WEST MARINE
Fuel/Water Separator These filters were tested by Powerboat Reports (March 2003) and rated better than other more expensive funnels. Teflon-coated, stainless-steel filter separates water and dirt from gasoline, diesel and kerosene fuels. Made from industrial standard electroconductive polypropylene that can be grounded for extra safety. Tested and rated by Powerboat Reports (March 2003) better than other more expensive funnels. Separate water and dirt from gasoline, diesel and kerosene fuels.
|
Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
|
Drop-In Hidden Horn from AFI
Designed for easy installation, this hidden horn mounts from the outside. Compact in size, but capable of 107db loudness. Comes with both black and white snap-on ASA plastic grilles. A weatherproof fabric liner lets sound through, but keeps water out. Prewired for 12V installation. Material: ABS plastic . Loudness dB: 107dB . Design Standards: Meets ABYC specs for boats up to 12 meters . Dimensions: 2"H x 3-3/8"W x 3-1/4"D . Power Requirements: 12 Volts .
|
Aft-Deck Shower System from ATTWOOD
This compact hot/cold shower stores neatly in its own compartment on the stern or in the head. Includes a handheld shower spray head with shutoff, 6' hose, hot/cold water controls and a cover. Easily hooked into your freshwater system. Compartment is drilled for six #8 fasteners. Material: High-impact plastic . Dimensions: 9-1/2"H x 5"W x 2-1/4"D . Hose Size: 6'L . Port Sizes: 1/2" NPT .
|
Rechargeable Signal Air Horn from TAYLOR
Environmentally safe air horn uses air as a propellant, instead of the traditional gas-filled designs. It's economical too. no more expensive refills to buy. Recharges in seconds with a gas station air pump, air compressor, or any other mechanical compressed air source including hand pumps. Works in all weather extremes and can safely be used or stored near sources of heat. Provides approximately 20 blasts per charge. This loud horn puts out a powerful 120db. Meets all USCG regulations.
|
G/Flex 655 Resin 4.75 Gal. from WEST SYSTEM
G/flex 655 Thickened Epoxy Adhesive comes with a thickening agent already added. G/flex offers important features: Toughness and Flexibility G/flex has been toughened. With a modulus of elasticity of 150,000 psi (WEST SYSTEM 105 Resin/205 Hardener has a modulus of elasticity of 450,000 psi), G/flex is more flexible and can deflect further than WEST SYSTEM 105/205, while being much stiffer than typical adhesive sealants. Bonds to wet and damp surfaces G/flex has the ability to glue damp woods.
|
G/Flex 650 Hardener 4.75 Gal. from WEST SYSTEM
A toughened, versatile, liquid epoxy for permanent waterproof bonding of fiberglass, ceramics, metals, plastics, damp and difficult-to-bond woods. G/flex offers these important features: Toughness and Flexibility G/flex has been toughened. With a modulus of elasticity of 150,000 psi (WEST SYSTEM 105 Resin/205 Hardener has a modulus of elasticity of 450,000 psi), G/flex is more flexible and can deflect further than WEST SYSTEM 105/205, while being much stiffer than typical adhesive sealants. .
|
Teak Binocular Rack 7X50 from SEATEAK
Teak Accessories for Cabin & Cockpit Using only plantation-grown teak, these fine accessories make life aboard more pleasant.
|
|
8, 1 Power Ratio from LEWMAR, Gearset from SIERRA, Single from TELEFLEX
![M-120 Sport Tabs, 10" x 12", Fits boats 20' - 23' L from BENNETT MARINE]( "M-120 Sport Tabs, 10\" x 12\", Fits boats 20' - 23' L from BENNETT MARINE")
|
|
Home -> Engine Systems -> Trim Tabs & Hydrofoils->Super Sport Tabs
Get up on plane quickly, correct for uneven loads, increase speed and improve your fuel economy by up to 30%. They have unique, “batwing” drop fins on the outside of the trim tab that not only creates more lift, but they also fit in smaller spaces (10" x 10") than standard trim tabs. They are well-suited for boats 18'-23' including bay boats, bass boats, ski boats or center consoles. Includes quick-connect fittings and is self-bleeding. Includes free installation video.
Part No: M-120-SV
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Marine AF 45 - TBT Free Ablative Antifouling
Marine AF 45 - TBT Free Ablative Antifouling (Commercial/Industrial only) Moderate copper load (45%) ablative antifouling. TBT free. Used for fouling control on coastal vessels requiring drydock intervals less than 36 month. Specifically designed for Steel and for (select styles) aluminum ships.
Part No: 4504-5G
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting->Series 32 LED Navigation Lights
LED Navigation Lights for big boats Use on power or sail vessels up to 65'7" (20m). Two nautical mile visibility. Patented prism lens technology provides the highest quality LED illumination in the industry. Energy-efficient LED technology significantly reduces power draw compared to incandescent lights. ABYC, USCG, IMO, CE and RINA certified. Case Material: Polycarbonate . Mounting Hardware: Sold separately . Volts: Operates on 12V or 24V with no modification needed . Draw: 0.
Part No: 32607-7
|
|
|
|
Patterned to fit pontoon boats having rails approximately 30" high. 4-ply fold-over seams 1", heavy-duty, UV-resistant tiedowns 1,000s of styles & sizes to fit nearly any boat Designs that fit outboard and inboard motors Tough enough to handle over-the-road trailering. Poly Cotton Fabric: Trailerable 65% polyethelyne/35% cotton Breathable Mildew & Stain Resistant Water Repellant Heavy-gauge shock cord in hem 2-year limited warranty Color: Silver Gray.
Part No: 70308
|
|
|
|
Home -> Engine Systems -> Control Systems->KE-4 Electronic Remote Control System
This longlasting control has been extensively tested, and performs well in excess of a typical mechanical system. Features fail-safe operation, self-diagnosis system, control head with built-in station select switch, neutral warm up provision, optional mechanical backup, overload protection. Use one control unit and one actuator for single engine boats with up to four pilot stations. Use two control units for two engine boats with up to four stations. Call 1-800-BOATING for more information.
Part No: NM0511-00
|
|
|
|
Home -> Fishing -> Reels -> Conventional Reels->Trinidad Reels
Solid, one-piece graphite frame. Large drag surface and precise lever drag. Three ball bearings deliver a smooth, predictable response. 1166917 390/12lb Capacity Yards/Test 3BB 16. 4 oz. .
Part No: TN-40
|
|
|
|
Home -> Cabinet & Deck Hardware -> Hatches & Ports->Low-Profile Hatches
Now Lewmar has created a two-piece frame with tough, gray acrylic that can be replaced simply by unscrewing the frame and inserting the new lens. The seal and acrylic are fitted into the aluminum frame to produce a stronger, more leak-proof hatch. All hatches feature a vent position, flange base and sizes 30 and larger have lockable internal and external handles for added security. CE Area II approved. Low-profile hatches have 8mm acrylic in sizes 00 through 54, and 10mm acrylic in size 60.
Part No: 39950030
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting -> Navigation Lights->LED Navigation Lights
Lopolights are available for boats up to 164' (50m). Each light is individually tested and certified, concluding with a 36-hour Reliability Stress Screening so you can just install it and forget it! Why should you buy Lopolights? • Completely waterproof (rated IP68+ submersible): Interior is fully filled and sealed with special epoxy resin. • Rated for over 50,000 hours of operation. Not damaged by vibration. • Low power consumption: Less than 30% of the draw of a standard incandescent lamp.
Part No: 200-012
|
|
|
|
Home -> Cabinet & Deck Hardware -> Hatches & Ports -> Deck Hatches->Medium-Profile Hatches
Until now, replacing scratched or cracked lenses meant sending the lid to the manufacturer or paying a professional to repair it. Now Lewmar has created a two-piece frame with tough, gray acrylic that can be replaced simply by unscrewing the frame and inserting the new lens. CE-certified aluminum frame has smooth, rounded edges, inset hinges and rounded corners for snag-resistance. All hatches have flange bases. Medium-profile hatches have a deeper frame section and 12mm acrylic in all sizes.
Part No: 39940020
|
|
|
|
Home -> Electronics -> Boat Instruments->Self Leveling Radar Mounts
Self leveling radar mounts guarantee your radar will stay level with the horizon as the boat heels or rolls.
Part No: RM-3TUBE-10
|
|
|
|
Home -> Anchor & Docking -> Fenders & Docking->De-Icers
Protect your vessel against the damaging effects of iceKasco De-Icers circulate subsurface water (which is warmed by geothermal heat) to the surface to melt ice and prevent its formation. This helps to protect your boat and dock from lifting damage due to "ice jacking" and the shearing and crushing damage caused by ice expansion. Many factors affect the size of the open water area. In general, the 1/2hp model keeps a 50' dia. area from freezing while the 3/4hp model keeps a 75' dia.
Part No: 2400D050
|
|
|
|
Home -> Seating & Covers -> Seating -> Helm & Fishing Seats
Great looking and easy to maintain--just hose it down once in a while. Ladder-back styling with molded armrests. Thick, removable cushions on the seat and arms make long waits for the fish a lot more comfortable. Swiveling spider and slider, can adjust it fore and aft. 15'' anodized aluminum pedestal with 9'' diameter base.
Part No: 7200-01
|
|
|
|
Home -> Sailboat -> Tiller & Rudder->Chain & Wire Kits
Pre-assembled with one length of roller chain and two lengths of wire. The connections between wire and chain are covered in clear shrink plastic to prevent fouling. All roller chain and wire rope are stainless, and the chain end fittings are cotter-pinned for ease of maintenance. Now includes connecting hardware/ tensioning kit.
Part No: 774-2S2B13
|
|
|
|
Home -> Engine Systems -> Engine Parts->Exhaust Manifolds, Elbows, Risers
Sierra exhaust manifolds, risers and elbows are 100% painted where the competition sends theirs out in primer alone. When the technician buys a manifold from us, time spent watching paint dry is saved for other profit generating work. Manifolds, risers and elbows are individually packaged in Instapack, an expanding packaging foam that keeps the part from chipping and breaking during transportation Water left in manifolds over the winter months can freeze and crack requiring replacement.
Part No: 18-1904
|
|
|
|
Home -> Safety -> PLBs, EPIRBs, Life Rafts, Survival->Liferaft Cradles
Cradles are an important part of liferaft safety. They make it easy to mount your liferaft on deck, where it's easily accessible in an emergency. All of our cradles accept hydrostatic releases, which we highly recommend for added safety. A hydrostatic release deploys the raft and inflates it automatically when the release comes in contact with the water. Cradles are constructed of 1" (25mm) tube diameter 316 stainless steel. They are designed to be mounted horizontally on deck .
Part No: 40446
|
|
|
|
Home -> Plumbing -> Marine Sanitation
Offering residential “just like home” styling and dependable push-button performance for worry-free days afloat, this head features a free standing pump that easily adapts for right- or lefthanded installation. Clean flushes are assured by the powerful Nozzle Flush System and the crevice-free vitreous china design makes it easy to clean. Type: Electric . Features: Residential styling, free-standing pump . Draw: 10A @ 12V DC. Port Sizes: 3/4" inlet, 1-1/2" discharge . 2"H x 21.
Part No: 41211
|
|
|
|
|
Home -> Electrical -> Exterior & Navigation Lighting->Series 32 LED Navigation Lights
LED Navigation Lights for big boats Use on power or sail vessels up to 65'7" (20m). Two nautical mile visibility. Patented prism lens technology provides the highest quality LED illumination in the industry. Energy-efficient LED technology significantly reduces power draw compared to incandescent lights. ABYC, USCG, IMO, CE and RINA certified. Case Material: Polycarbonate . Mounting Hardware: Sold separately . Volts: Operates on 12V or 24V with no modification needed . Draw: 0.
Part No: 32606-7
|
|
|
|
|
Home -> Safety -> PLBs, EPIRBs, Life Rafts, Survival->Liferaft Cradles
Cradles are an important part of liferaft safety. They make it easy to mount your liferaft on deck, where it's easily accessible in an emergency. All of our cradles accept hydrostatic releases, which we highly recommend for added safety. A hydrostatic release deploys the raft and inflates it automatically when the release comes in contact with the water. Cradles are constructed of 1" (25mm) tube diameter 316 stainless steel. They are designed to be mounted horizontally on deck .
Part No: 40447
|
|
|
|
Home -> Seating & Covers -> Seating->Matrix Fully Upholstered Seat
Superior Styling, Unequaled Comfort and Infinite Design Possibilities Matrix is the first seat built to accept custom-shaped components that give you the ability to build a completely original seating system. Built into the core of every Matrix seat, the 4G Mesh Shock Absorbing System is completely integrated within the seat pan to simultaneously support the sculpted foam pack and absorb shock without transferring impact to the boater. Static Comfort Elastic mesh will not deform under pressure.
Part No: 98823-2
|
|
|
|
Home -> Safety -> PLBs, EPIRBs, Life Rafts, Survival->Imperial Immersion Suit
These superior-quality immersion suits have been in production since 1959—and in fact are the very first immersion suits to ever be seen in the maritime market. Each suit is meticulously crafted and pressure-tested upon completion. View Approval Certificates here. Key Features USCG/MED Approved / SOLAS Compliant. Wide legs for quick donning. Dual-zipper pull tabs. Inflatable high-rider ring for additional freeboard and buoyancy. Snug-fitting face seal is flexible and comfortable.
Part No: 80-1409-C
|
|
|
|
Home -> Sailboat -> Tiller & Rudder->Radar Pods
Manufactured from thermoformed uPVC. Allows for 1 x Radar with 7" screen color version .
Part No: 89400222
|
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Marine AF 45 - TBT Free Ablative Antifouling
Marine AF 45 - TBT Free Ablative Antifouling (Commercial/Industrial only) Moderate copper load (45%) ablative antifouling. TBT free. Used for fouling control on coastal vessels requiring drydock intervals less than 36 month. Specifically designed for Steel and for (select styles) aluminum ships.
Part No: 4502-5G
|
|
|
|
Home -> Engine Systems -> Fuel Tanks->V-Bottom Polyethylene Fuel Tanks
These rugged permanent tanks are molded of gray cross-linked polyethylene for strength and no-leak durability. Each tank is individually inspected and tested to assure its quality. Includes electronic fuel-level sending unit and fuel withdrawal fitting.
Part No: X90-2166
|
|
|
|
Home -> Watersports -> Tow Ropes & Accessories -> Watersport Accessories->The Pod - Universal Mounts
A universal mount that fits all inboard and outboard boats. Self supporting with two stainless steel arms Secured by 5000 lbs.
Part No: S102TG
|
|
|
|
Home -> Boats & Motors -> Kayaks & Canoes -> Inflatable Kayaks->High-Performance River Kayaks XK1 and XK2
The XK1 has pronounced rocker, but can easily be paddled in a straight line in calm water. The XK2 is a dual purpose boat with moderate rocker that is a roomy, handsome and trim touring kayak with plenty of room for gear. Both include crossstitch PVC High Pressure floors, inflating to 7psi, which add rigidity. Hulls are composite SevyTex polyester/PVC sandwich with puncture-resisting technology. Dropstitch High Pressure floors inflate to a rigid deck . Self bailing cockpits for rough water.
Part No: U231CMB-00-000
|
|
|
|
Home -> Sailboat -> Traveler, Tracks & Vang -> Mainsheet Traveler->Midrange Captive Ball Traveler Cars
Recirculating ball-bearing travelers move freely under non-vertical loads and have a low-profile design. Captive balls allow easy installation. Built for high loads on offshore cruisers and racers. Toggle cars are designed with low pivot points for efficient load transfer and serve as a stand-up for mainsheets. Application: Mainsheet systems, offshore boats 27' to 34'. Ball Bearings: Recirculating captive Torlon bearings in open races. 1617, 1618. Material: Machined one-piece aluminum car.
Part No: 1636
|
|
|
|
Home -> Sailboat -> Winches->Ocean Series One- & Two-Speed Self-Tailing Winches
Advanced technology and innovative features has made Ocean Series the world’s most popular winches. Racing sailors appreciate the smooth operation and flawless performance. Fewer moving parts means fewer problems and simpler maintenance. And Ocean’s unique grip pattern makes rope handling easy—easier still with a self-tailing model, which incorporates Lewmar’s Wavespring feature, a combination of the gentle Wavegrip and self-adjusting springs to handle today’s smaller diameter ropes.
Part No: 49014001
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains
**Gear Set|**Gear Set.
Part No: 18-2200
|
|
|
|
|
Home -> Engine Systems -> Engine Parts
**Starter-Outboard|**Starter-Outboard.
Part No: 18-6425
|
|
|
|
|
**98-05SUGRSND TAN 2+4 DC JT P.
Part No: 66218UB
|
|
|
