Prop Nut Kit, Yamaha 40-50HP from SIERRA
An excellent emergency item to carry in your toolbox, for those occasions when the prop nut is misplaced or lost.

Prop Nut Kit, Yamaha V4/V6 from SIERRA
An excellent emergency item to carry in your toolbox, for those occasions when the prop nut is misplaced or lost.

Shift Cable Bellows for Volvo SX, OMC SX and Cobra from SIERRA
Seals the shift cable as it passes through the transom.

CARB GASKET KIT from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Yamaha Carb Kit from SIERRA
Sierra carb kits and gaskets for engine tune ups.

Replaces OMC P/N 378444 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

For Chrysler/Force, 89-817109A2 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Lower Unit Seal Kit from SIERRA
Sierra 18-2623 OMC Gear Housing Seal Kit.

Lower Unit Seal Kit from SIERRA
Lower Unit Seal Kit.

Water Circulating Pump - #18-3599 - Volvo #3851982-3, 3853850; Mercruiser #811841, 850399, 850399-1 from SIERRA
Water Pumps The water pump is the heart of your inboard or I/O cooling system. All Sierra pumps are bidirectional and can be installed on reverse rotation engines. The pumps are also powder coated for additional protection. Includes mounting gasket. Pumps include brass bi-directional impellers, brass plugs and fittings, carbon resin seal, all mounting gaskets, stainless steel seal cup and spring, stainless steel back plate (where required), and powder coating for maximum corrosion protection.

Johnson/Evinrude Outboard Starter, 120 to 140hp V4 (1985-99), 10 tooth drive gear from SIERRA
Sierra's new and remanufactured starters are the only marine starters that meet Marine UL standards. Sierra's remanufactured starters all have new solenoids, drives, bushings, brushes and springs. The bodies are powder coated for greater corrosion resistance. Sierra has entered an agreement with United Technologies to market their complete line of outboard starters and components. All are 100% load tested . Our remanufactured starters are covered by Sierra's customer satisfaction warranty .

30GPH Cartridge, Replaces Racor S3240 from SIERRA
High-performance fuel injected engines require ultimate fuel filtration, separation of water from the fuel supply and maximum fuel flow. Sierra’s filter elements deliver all three of these critical performance factors. 7900-Series 10 micron filters eliminate harmful contaminants at over 90% efficiency, while removing over 98. They’re engineered for today’s sterndrives and inboards, along with 2-cycle and 4-cycle outboards. That is why a high efficiency water separating filter is so important.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

Micro Carbo-Cam Cleat Kit with 423 Cam, 329 Fairlead from HARKEN
Micro Cam-Matic cleats are legendary for smooth, positive operation when holding and releasing control lines. Mounted aft of the cam, fairleads allow you to engage and release a line up to 45° on either side of the cam. Mounted ahead of the cam, fairleads allow moving lines, such as small catamaran traveler controls, to lead properly. Cam kits include: Cam-Matic® cam cleat: Pawls open/close easily on ball bearings . Large diameter low-friction guides with stainless steel tubes protect lines .

Single Line Mainsail Reef Kit from HARKEN
Makes it simple to reduce sail. Harken has simplified the single line mainsail reefing kit developed from Garry Hoyt’s patented concept making this kit lighter and easier to install. A must for single handers or shorthanded sailing. Reefing with the kit is simple: ease the halyard to a predetermined mark, tension the reefing line, and re-trim the sail. For boats to 27'. Everything you need for installation is included except the line, a cleat and stopper. Ideal for boats from 22' to 27' (6.