Top Sellers
Twisted Pair Wire with Shield from ANCOR MARINE
Similar to Ancor duplex wire, except that the conductors are twisted and surrounded by a copper shield for extra protection against noise and electrical interference. Red/black conductors. Recommended by ABYC for DC wiring near compasses and other magnetically - sensitive devices. Sold per foot. Wire Type: Twisted Pair . Construction: Tinned Copper . Conductors (Color and # of): 1 Red, 1 Black . Color of Exterior Insulation: White . Shielding: Copper Shield . Approvals: UL, ABYC, CSA .
|
Calibrated Resin Pump Set from MAS EPOXY
For use with 1 quart, 1/2 gallon, 1 gallon, 4 gallon and 5 gallon size containers.
|
|
|
Rounded Oval, 8-1/2"W x 11-1/4"L x 5-1/4"D, 1" Flange, 1-1/2" Drain from AMBASSADOR MARINE
Made from 304 stainless steel and mirror-polished to a deep luster, these sinks incorporate SoundKOTE Noise Reduction Technology to reduce the unpleasant clanging associated with many metal sinks. Flanges permit over- or under-the-counter mounting. Low-Profile 90° drains fit standard 1"ID hose and are slanted to maximize drainage.
|
Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.
|
SeaStar Helm Seal Kit from TELEFLEX
Replacement shaft seal kit HS5176 fits various post-1990 SeaStar 1. 4, 1. 7 (I), 2. 0, 2. 4 (II), SeaStar Pro and SeaStar helms.
|
P-Trap Fuel Surge Protector from ATTWOOD
One combined product eliminates the need to install both a fuel line vent and a surge protector. Inertia of surging fuel drives the surge ball against upper seat, closing the large vent opening and limiting passage to smaller openings, which reduces fuel flow and minimizes spillage. Operates in any orientation within 45° of vertical. Baffles resist water intrusion during normal sea conditions and washdown. Constructed of glass filled polypropylene to withstand oil, gas, alcohol blended fuels.
|
Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.
|
|
|
1/4" Dia. Stamped Halyard Shackle, 1,000SWL from SCHAEFER
Stamped Halyard Shackles haveflared heads with cross pin retainer for attachment to rope. Captive design prevents accidental opening Quick release pin #93-42 - 1/4" Shackle Pin dia. , 1/2" Inside Width, 1,000 SWL #93-45 - 5/16" Shackle Pin dia.
|
Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.
|
WL/1 Fairlead Model from SPINLOCK
New low-profile design easily mounts to 1" stanchion using internal clamping system. WL/2 sheave model utilizes unique tracker ball angle adjustment. WL/1 Fairlead model includes stainless-steel bullseye for strength.
|
1-7/8" Brass Standard Hasp from ABI
Highly polished brass . Fixed eye (does not swivel). 1"w x 1-7/8"L. Padlock hole diameter 5/16" .
|
1/4" NPT X 3/8" Brass hose barb from MOELLER
1/4 NPT X 3/8" Brass Hose barbs with male threads.
|
|
|
|
7oz, 1oz, 0, 1, SWL, 1, 200lb, Rainjammer PVC Rain Suit, ON, 2-1
|
|
Home -> Plumbing -> Hose & Hose Clamps -> Bulk Hose->Series 250 ShieldsFlex II Marine Water/Exhaust Hose with Wire
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .
Part No: 116-250-2123
|
|
|
|
Home -> Sailboat -> Blocks->Wire Blocks
Single blocks can double the power of a rope tackle using a cascading block system. Blocks up to 1" sheave diameter are stainless steel with nickel-plated brass sheaves. Blocks over 1" sheave diameter have removable anodized aluminum sheaves with Delrin® bushings. Micro Kite Blocks are very strong, super-lightweight.
Part No: RF560
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Wood Screws - Flat Head Slotted - Bulk Packs
Type 18-8 Stainless Steel.
Part No: 296A
|
|
|
|
Home -> Engine Systems -> Engine Parts
**FillTube-Lower Unit|**FillTube-Lower Unit.
Part No: 18-9787
|
|
|
|
Home -> Paint & Maintenance -> Cleaners, Soaps & Polishes->NanoTec Fiberglass Cleaner Wax - Pure Oceans
Working at the “nano” level, this formula removes light oxidation, seals surfaces and provides a protective, high-gloss finish for fiberglass.
Part No: 6181
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Machine Screws - Slotted Round Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 1031A
|
|
|
|
Home -> Sailboat -> Blocks->Series 29 Utility Blocks
Stainless-steel cheeks and Acetal sheaves for light applications like dinghy vangs or outhauls or cunninghams and spinnaker controls on larger boats. Sheave: UV stabilized Acetal. Bearings: Plain bearings. Sheave Size: 1-1/8" (except RF341, 1"). Line Diameter: 5/16" max. (except RF341, 3/16" max. ). Cheek Material/Finish: Polished 316 Stainless.
Part No: RF285
|
|
|
|
Home -> Sailboat -> Blocks->Series 25 Lightweight Blocks
Stainless-steel blocks with Acetal sheaves for reduced weight. Slightly flared cheeks provide fair leads on dinghy control lines. Sheave: UV stabilized Acetal . Ball Bearings: Plain bearings . Sheave Size: 1" (25mm) . Line Dia. : 1/4" max. . Cheek Material/Finish: Polished 316 Stainless .
Part No: RF574
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Machine Screws - Slotted Flat Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 938A
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Lock Washers, Type 18-8 Stainless Steel - Bulk Packs
Type 18-8 Stainless Steel - Bulk Pack lock washers, in packs of 10, 25, 50 or 100.
Part No: 1428C
|
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners->Machine Screws - Slotted Flat Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 980B
|
|
|
|
Home -> Sailboat -> Blocks->Micro Blocks
Extremely lightweight, free running blocks. Designed for any number of uses on dinghies and for lightly-loaded control lines on boats of all sizes (inside masts and booms, lead car returns, tackle, etc. ). Where applicable, blocks use #10 fasteners. Sheave: Delrin® . Ball Bearings: Delrin® . Sheave Size 7/8" (22mm) . Line Dia: 1/4" max. . Cheek Material/Finish: Polished 316 stainless . Shackle/Strap Type: Fixed loop, loop with shackle .
Part No: 292
|
|
|
|
Home -> Fasteners -> Mechanical Fasteners -> Fasteners (100 Pk Bagged)->Machine Screws - Phillips Pan Head - Bulk Packs
Type 18-8 stainless steel.
Part No: 5509C
|
|
|
|
Home -> Sailboat -> Blocks->Rope/Wire Bullet Blocks
Designed for vangs, outhauls, shrouds where wire is used or for rope where loads are too high for regular bullet blocks. Roller bearings handle high loads better than ball bearings. Where applicable, blocks use #10 fasteners. Sheaves are aluminum for strength. Sheave: Teflon® impregnated Hardkote anodized aluminum . Bearings: Delrin® roller bearings . Sheave Size: 1-1/8" (29mm) . Line Dia. 5/16" max. . Cheek Material/Finish: Plastic with stainless strap .
Part No: 109
|
|
|
|
Home -> Sailboat -> Blocks->30mm Synchro Control Blocks
Quality Lewmar blocks in compact 30mm size Lightweight 30mm blocks feature the same advanced materials and open design of Lewmar's 40mm blocks for high performance and reduced weight. The MRT (Metal Replacement Technology) sheaves, combined with the stainless steel central race and balls, deliver the ultimate efficiency and weight advantage. Sheave: MRT Composite reinforced plastic Ball Bearings: Stainless-steel central race and balls Sheave Size: 1-1/16" (30mm) Line Dia.
Part No: 29901361
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes -> Shaft/Prop Nut Anodes->Zinc Streamlined Collar Anodes
Canada Metal zincs are composed of an alloy that meets Mil-Spec MIL-A-18001 for sacrificial anodes. This alloy is mostly zinc, but with measurable concentrations of cadmium (~0. 1%) and aluminum (~0. 25%). The additional cadmium causes the anode to erode from the surface inward, which causes a ''sandblasted'' appearance to the surface.
Part No: CMX35
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Bronze Round Strainers
Helps keep debris out of water-intake lines that do not require a scoop strainer. Designed for use with an existing thru-hull fitting. Marine UL-listed.
Part No: 0086DP2PLB
|
|
|
|
Taylor Made 1324 Canadian Courtesy Ensign Flag 12 x 24 . Perma-print dyed nyon. Canvas heading.
Part No: 1324
|
|
|
|
Home -> Electrical -> Switches, Fuses & Accessories -> Switches->Toggle Switches
All non-corroding construction with moisture-repellent insulators and silver contacts. MOM/M-On denote momentary. Lighted Toggle Swithces: White Off/Red On Chrome-Plated: Single Pole Switches, Off/On positions only Max 10A@12V Fit panels to 1/4" thick Mount in 15/32" dia.
Part No: 54100-BP
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Marelon Mushroom Heads, Threaded
Marelon 251 Series Full Threaded/Mushroom Head Thru-Hull Connectors Forespar® series of the Thru-Hull Connectors are precision molded in high strength Marelon®. Their great strength, light weight and complete freedom from corrosion and electrolysis make them the ideal Thru-Hull Connectors for use above or below the waterline. All Thru-Hull Connectors must be installed with proper bedding compound. CF 2505 ½), indicates a Thru-Hull Connector that has been fitted with a strainer. Full threaded.
Part No: 906016
|
|
|
|
|
Home -> Cabinet & Deck Hardware -> Hatches & Ports->Beckson Portlight Screens
.
Part No: SCR-414
|
|
|
|
Home -> Engine Systems -> Engine Lubrication -> 4 Stroke Oil->Heavy-Duty 4-Cycle Engine Oil
Heavy-duty, 4-stroke marine oil protects engine, even under severe conditions Provides outstanding protection for diesel and four-cycle inboard/outboard gasoline engines in marine environments. High viscosity and film strength provide protection in high speed/high load applications. Helps reduce corrosive wear. Meets or exceeds major manufacturers' warranty requirements and API service CI-4/SL (15W-40 only), CF-4, CF-2, CF/SJ. Exceeds Original Equipment Manufacturer’s warranty.
Part No: 5073660
|
|
|
|
Home -> Foul Weather Gear & Jackets -> Foul Weather Gear -> Foul Weather Gear->Rainjammer PVC Rain Suit
Affordable and lightweight rain gear is great for fishing and boating in wet conditionsJacket features raglan sleeves with elastic cuffs, air vents under arms, fully vented cape back and two large utility pockets. Pants have elastic waist and adjustable cuffs. Best use: Protection from rain showers. Not breathable. Classification: Inshore. Imported. Yellow. Elastic cuffs. Two large utility pockets.
Part No: YELLOW-S
|
|
|
|
Home -> Anchor & Docking -> Chain & Mooring->Stainless-Steel BBB Anchor Chain
Stronger than galvanized chain and has a higher working load than proof coil chain of the same size. This chain complies with all requirements of DIN 766 BBB chain and fits most standard windlasses.
Part No: S0601-0007
|
|
|
|
|
Home -> Electrical -> Switches, Fuses & Accessories->Nylon Cable Clamps
.
Part No: 401505
|
|
|
|
Home -> Books & Videos -> Cruising Guides -> Intracoastal Waterway->Skipper Bob™ Atlantic & Gulf ICW Guides
Skipper Bob and his wife Elaine cruised more than 44,000 miles on the East Coast of the United States. Their travels have taken them up and down the Intracoastal Waterway numerous times. They completed the Great Loop Route and sailed to both the Bahamas and the Dry Tortugas. They took their trawler through the Erie, Rideau, Richelieu, and Trent Severn Canals. Marinas Along the Intracoastal Waterway Fuel prices, transient slip fees, long-term slip fees, do-it-yourself yards, and haul out fees.
Part No: SBAAICW
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Quick Connect Water System Fittings
.
Part No: WX1563
|
|
|
|
|
Home -> Engine Systems -> Engine Parts
**Gasket-Head|**Gasket-Head.
Part No: 18-3807
|
|
|
|
Home -> Sailboat -> Shackles, Snaps & Fittings
Stainless steel screw shackle for wire rope. Length: 36mm (1. 44''). Pin size: 5mm (0. 2''). Opening: 13mm (. 52''). Strap width: 13mm (.
Part No: HA4828/1
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes -> Outboard/Outdrive Anodes->Outboard Anode, Mercury/Force/Mariner
Outboard Anodes - Mercury/Force/Mariner Manufacturer: Canada Metals.
Part No: CM826134M
|
|
|
