Top Sellers
1/4" NPT X 3/8" Brass hose barb from MOELLER
1/4 NPT X 3/8" Brass Hose barbs with male threads.
|
1-7/8" Brass Standard Hasp from ABI
Highly polished brass . Fixed eye (does not swivel). 1"w x 1-7/8"L. Padlock hole diameter 5/16" .
|
3/8" NPT Aluminum hose barb from MOELLER
3/8 NPT X 3/8" Aluminum hose barb with male threads.
|
Spring Loaded Ring Pull, Square 2 x 2 3/8" from WEST MARINE
Spring-loaded ring immediately returns to flush when released. Type 304 stainless steel . Size: 2 x 2 3/8" .
|
1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .
|
Zinc Grouper Anode from CANADA METALS
Supplements your boat's existing anodes An excellent anodic device to supplement a vessel’s existing anode system, especially to counteract stray current from defective shore power. Clip to bolt on outdrive. Clip to grounding strap if possible or wire items together with copper wire and clip to wire. Do not connect to negative battery terminals. Dimensions: 8 1/4"L x 3 1/4"W x 1 3/8"D.
|
5/16" Wire Rope Clamp from SEADOG
Investment Cast 316 Stainless Body / AISI 304 Stainless U-Bolt. Accepts 5/16" wire. 1-5/8" Long. 1-3/8" wide.
|
Rim Latch Sets - Reverse Bevel with Flush Strike from PERKO
Chrome-plated zinc. Sliding lock button. Case size: 2 1/8'' x 1 3/4''. Escutcheon Size: 4 3/8'' x 1 1/4''. For Door: 5/8'' to 1 3/8''.
|
3/8 inch inline fuel filter from SIERRA
For use on McCulloch/Scott-Atwater, Suzuki Outboard and Yamaha Outboard 18-7831 is replacement for Johnson/Evinrude Outboard #398319.
|
West Marine/SOSpenders PFD Rearming Kit, 3/8" Threaded Cylinder Neck Dia. from WEST MARINE
West Marine/SOSpenders PFD Rearming Kit Style: Automatic. Cylinder Weight: 38g. Cylinder Neck Diameter: 3/8" or 1/2" threaded. Inflator Type: Halkey-Roberts. Kit Contents: Cylinder, green pin, bobbin. PFD Brands Commonly Used With*: West Marine/SOSpenders PFD . Inflator Number: V85000. *The column "PFD Brands Commonly Used With" is not all inclusive. Rearming Kits may be used with other brands and vests.
|
Glasskoter Resin Roller Cover - 9" x 3/8" Nap from CORONA
For epoxy and polyester resinPhenolic core. Woven mohair. 3/8" nap for semi-smooth or 1/8" nap for fine finishes.
|
Series 60 Orbit Block, Single Light-Load, 2-3/8" Sheave Size, 1,710lb. SWL, 4.7oz. from RONSTAN
These exceptionally strong blocks feature the performance Orbit sheave with captive Acetal ball bearings for side thrust loads, eliminating the need for side retainer plates. The 75mm webbing block (RF79107) can be used where swivel head and shackle attachment is not required to achieve further weight savings. Sheave Size: 2-3/8" (60mm) or 3" (75mm). Line Diameter: Series 60: 1/2" (12mm), Series 75: 9/16" (14mm). Cheek Material/Finish: Anodized aluminum.
|
Teak Plugs - 3/8" from SEAFIT
Use these teak plugs to cover screw heads or fill small holes for a beautiful smooth finish to your installation. Sizes: 1/4" 5/8" 5/16" 3/8" 1/2" 1".
|
3/8" Bow/Stern Eye - 1.03" ID Between Studs x 4.63" Thread Length from SUNCOR
Bow / Stern Eye 304 Stainless Steel - Formed . Each U-Bolt set includes four nuts (two standard and two beveled) . Includes one bow plate, and one stern plate. . Threads are "UNC". . Stock size: 3/8" . ID between studs: 1. 03" . Thread length: 2. 50" .
|
3/16" Stock Dia. U-Bolt, 1-3/8” Thread Length, 1-3/16" Hole Spacing, 1" Eye Dia. from SEAFIT
Stainless steel U-Bolts have metric threads. The top plate is held in place by small ears that are forged into the U-bolt. Includes matching backing plate. ShWt .
|
|
1 3/8 Inch Plumbing
|
|
Home -> Plumbing -> Hose & Hose Clamps->T-Bolt 316 Stainless-Steel Exhaust Hose Clamps
Designed to assure proper coupling retention for large ID marine exhaust hose. T-Bolt Band Clamps offer a 360° clamping surface, and are ideal for any below-waterline application. 3/4" band spreads the clamping force evenly around hose. Designed to fit Shields hose #200, 210, and 250. Application: Exhaust hose clamp; intake hose clamp - any below waterline application; works with corrugated exhaust hose; full 360° clamping surface . Material: 316 stainless steel (0. 75"W) .
Part No: 118-720-1000
|
|
|
|
Home -> Plumbing -> Marine Sanitation->Tank Tender
Convenient, easy to use, simple to install and far superior to a dip stick, sight glass or an electric float gauge, Tank Tender uses air pressure to provide accurate readings for up to ten tanks. No electrical connection is necessary. With this system, you just select a tank to measure, pump in a small amount of air from the bridge and in two or three seconds you have a reading. We offer systems here for 30" deep tanks. Panels measure 4"W x 8"H x 2-7/8"D.
Part No: S30-3
|
|
|
|
|
Home -> Plumbing -> Marine Sanitation->Tank Tender
Convenient, easy to use, simple to install and far superior to a dip stick, sight glass or an electric float gauge, Tank Tender uses air pressure to provide accurate readings for up to ten tanks. No electrical connection is necessary. With this system, you just select a tank to measure, pump in a small amount of air from the bridge and in two or three seconds you have a reading. We offer systems here for 30" deep tanks. Panels measure 4"W x 8"H x 2-7/8"D.
Part No: S30-1
|
|
|
|
|
Home -> Plumbing -> Marine Sanitation->Tank Tender
Convenient, easy to use, simple to install and far superior to a dip stick, sight glass or an electric float gauge, Tank Tender uses air pressure to provide accurate readings for up to ten tanks. No electrical connection is necessary. With this system, you just select a tank to measure, pump in a small amount of air from the bridge and in two or three seconds you have a reading. We offer systems here for 30" deep tanks. Panels measure 4"W x 8"H x 2-7/8"D.
Part No: S60-3
|
|
|
|
|
Home -> Plumbing -> Marine Sanitation->Tank Tender
Convenient, easy to use, simple to install and far superior to a dip stick, sight glass or an electric float gauge, Tank Tender uses air pressure to provide accurate readings for up to ten tanks. No electrical connection is necessary. With this system, you just select a tank to measure, pump in a small amount of air from the bridge and in two or three seconds you have a reading. We offer systems here for 30" deep tanks. Panels measure 4"W x 8"H x 2-7/8"D.
Part No: S30-8
|
|
|
|
|
Home -> Plumbing -> Marine Sanitation->Tank Tender
Convenient, easy to use, simple to install and far superior to a dip stick, sight glass or an electric float gauge, Tank Tender uses air pressure to provide accurate readings for up to ten tanks. No electrical connection is necessary. With this system, you just select a tank to measure, pump in a small amount of air from the bridge and in two or three seconds you have a reading. We offer systems here for 30" deep tanks. Panels measure 4"W x 8"H x 2-7/8"D.
Part No: S60-1
|
|
|
|
|
Home -> Plumbing -> Marine Sanitation->Tank Tender
Convenient, easy to use, simple to install and far superior to a dip stick, sight glass or an electric float gauge, Tank Tender uses air pressure to provide accurate readings for up to ten tanks. No electrical connection is necessary. With this system, you just select a tank to measure, pump in a small amount of air from the bridge and in two or three seconds you have a reading. We offer systems here for 30" deep tanks. Panels measure 4"W x 8"H x 2-7/8"D.
Part No: S60-8
|
|
|
|
|
Home -> Plumbing -> Hose & Hose Clamps -> Hose Accessories->T-Bolt 316 Stainless-Steel Exhaust Hose Clamps
Designed to assure proper coupling retention for large ID marine exhaust hose. T-Bolt Band Clamps offer a 360° clamping surface, and are ideal for any below-waterline application. 3/4" band spreads the clamping force evenly around hose. Designed to fit Shields hose #200, 210, and 250. Application: Exhaust hose clamp; intake hose clamp - any below waterline application; works with corrugated exhaust hose; full 360° clamping surface . Material: 316 stainless steel (0. 75"W) .
Part No: 118-720-8000
|
|
|
|
|
Home -> Plumbing -> Hose & Hose Clamps->T-Bolt 316 Stainless-Steel Exhaust Hose Clamps
Designed to assure proper coupling retention for large ID marine exhaust hose. T-Bolt Band Clamps offer a 360° clamping surface, and are ideal for any below-waterline application. 3/4" band spreads the clamping force evenly around hose. Designed to fit Shields hose #200, 210, and 250. Application: Exhaust hose clamp; intake hose clamp - any below waterline application; works with corrugated exhaust hose; full 360° clamping surface . Material: 316 stainless steel (0. 75"W) .
Part No: 118-720-1120
|
|
|
|
Home -> Plumbing -> Bilge Pumps->Rule-Mate Fully Automatic Bilge Pumps
The new eco-friendly Rule Mate series of Bilge pumps feature a solid state water sensing technology that eliminates the need for a separate float switch. After the water is pumped out, another sensor shuts the pump off. The sensor's unique "field effect" technology is programmed to recognize the dielectric constant of water only. It's part of Rule's continuing commitment to preserving our waterway. The pumps are preferred by yachtsmen and commercial fishermen the world over.
Part No: RM1100A
|
|
|
|
Home -> Plumbing -> Bilge Pumps
Engineered to commercial standards. The Rule 2000 is the best selling high capacity submersible bilge pump in the world. 1-1/8" (28. 6mm) discharge outlet. Voltage: 12 Volts. Flow Rate: 2000 gph 7571 lph . Port Type: 1-1/8" (28mm) Hose barb . Amp Draw: 8. 4 amp . Fuse Size: 15 amp . Height: 7-3/4 inches 196.
Part No: 53S
|
|
|
|
|
Home -> Plumbing -> Marine Sanitation->Tank Tender
Convenient, easy to use, simple to install and far superior to a dip stick, sight glass or an electric float gauge, Tank Tender uses air pressure to provide accurate readings for up to ten tanks. No electrical connection is necessary. With this system, you just select a tank to measure, pump in a small amount of air from the bridge and in two or three seconds you have a reading. We offer systems here for 30" deep tanks. Panels measure 4"W x 8"H x 2-7/8"D.
Part No: S30-4
|
|
|
