|
|
316 Stainless-Steel Hose Clamp, 7/16" to 11/16", SAE Size 3 from ABA OF AMERICA
Hose clamps you can trust now and later Trust these clamps for secure hose connections. All components are Type 316 stainless steel for ultimate corrosion resistance. The smooth, unperforated band surface and rolled edges prevent hose damage. Band and screw threads are properly pitched, rendering the clamp virtually immune to vibration-caused back-off. Hoses are measured by inside diameter, so use a clamp with a maximum opening at least a 1/4" larger .
|
Body Width 2", Vertical Clearance 1", Shackle Diameter 5/16" from ABUS LOCK COMPANY
Set your own easy-to-remember combination on these padlocks with four-pin tumblers. You set the combination using the key provided. All brass internal components and a stainless steel shackle for superior corrosion protection. Type: Combination . Combination Type: Reset-able four tumbler . Material: Brass body and internal components, solid stainless shackle .
|
Flush Lock and Latch from PERKO
Black plastic, with stainless steel "D" ring handle, stem and lock nut. Two O-rings for increased water resistance. Position indicator shows open or closed position. Lock with 2 keys. Door thickness: 3/8" to 1-1/4" . Face plate dimensions: 2-7/8" x 2-7/8" . Adjustment latch bar: 1-1/16" to 2-9/16" .
|
ADJ 7-15-DL Whisker Pole, 83"/9lb. Collapsed Length/Weight, 202" Max. Working Length, 2" Tubing Diameters from FORESPAR
These telescoping whisker poles are heavy-duty two-section and three-section aluminum spars which can be extended to lengths up to 17' and securely locked in position by an internal twist lock device. Poles feature self-latching Ultra Series™ fittings on the inboard and outboard ends. Aluminum tubing. End Fitting Inboard: UPX. End Fitting Outboard: UPX.
|
Deluxe Windshield Washer Kit from AFI
Install your own windshield washer systemFits new or existing AFI Deluxe wiper arm and blade sets, with all the parts to outfit two wiper arms. The kit includes a 3 liter water tank with mounting bracket (8. 5"H x 7"W x 4. 5"D), 12V pump motor and 16' below deck clear tubing, 6' above deck black tubing, clips and sprayer fittings. You supply wiring, an in-line 3A fuse and On-Off momentary switch.
|
Adjustable Lock from TAYLOR
Three-part system provides easy snap-on/snap-off fender attachment and adjustment. A stainless base mounts to your boat, into which a peg snaps to hold the fender strap (sold separately). Fixed peg requires tying a knot to secure the fender at the desired height. Adjustable peg - adjust fender height by simply pulling on the strap. Max.
|
Adjustable Packing Nut Wrench from SEAFIT
Better than a pipe wrench If you are not equipped with wrenches that fit the nuts on your stuffing box, we suggest you purchase TWO of these. Why? Because you will need two to make an adjustment: One for the locking nut and one for the adjusting nut. These wrenches tend to be easier to use than pipe wrenches—especially in tight engine spaces where many boaters must work. Primary Usage: Adjust/remove inboard shaft packing nut . Size: 1" to 3" adjustable .
|
Adjustable Height Standard Friction Lock Pedestal Seat, Ribbed Series from GARELICK
Seat raises or lowers, locks at desired height . 2-7/8" (7cm) diameter stanchion tube, 9" (23cm) diameter base plate . Anodized protective finish helps prevent saltwater corrosion and weathering. . 2-7/8" (7cm) diameter ribbed stanchion tube, 9.
|
Outboard Lock - Merc/Mariner (40hp), 1/2" x 20 thread from MCGARD
Help make your outboard less attractive to thieves, and also keep it from vibrating loose while running. The vinyl-clad steel tube slides over the mounting screws and is secured with a hardened brass padlock. Padlock is recessed inside the tube to protect against cutting. Comes with two keys. *Fits: OMC 6-30hp, Merc/Mariner 8-25hp, Yamaha 9. 9-40hp, Suzuki 8-13hp.
|
Flip Lock Drain Plug 1" Stainless from SEAFIT DRAIN
Standard rubber and brass plug fits 1" transom drains on many production boats.
|
Stern Rail Outboard Motor Mount for 1" Railing from EDSON CORPORATION
Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with nonskid pad, bolted to the UV stable poly backing board always looks shipshape. no more varnishing. Comes complete with hardware to attach to any standard 1'' (2. 5cm) stainless rail. Warning: Be sure the engine is securely tied onto the backing board and the engine mounts are tightened whenever the engine is stored on Edson's Outboard Motor Mount.
|
Stern Rail Outboard Motor Mount - Aluminum for 1-1/4" Railings from EDSON CORPORATION
Built to hold motors up to 15 hp or 100 lbs/45 kg. Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with non-skid pad, bolted to the UV stable poly backing board always looks ship-shape… no more varnishing. Bottom cleat comes unattached so that it will fit any rail spacing. Note: 1-1/4” rail version comes complete with anodized aluminum bracket, stainless cleat and stainless U-bolt for 1-1/4” railing.
|
Rim Latch Sets - Reverse Bevel with Flush Strike from PERKO
Chrome-plated zinc. Sliding lock button. Case size: 2 1/8'' x 1 3/4''. Escutcheon Size: 4 3/8'' x 1 1/4''. For Door: 5/8'' to 1 3/8''.
|
Push-Lock Slam Latch with Finger Pull from SOUTHCO
For glove box and small door applications where security is needed. Built to withstand harsh marine conditions, this latch is constructed of durable hybrid polymer and stainless steel. Mounts easily in a 1" cutout. Maximum working load: 120 lbs.
|
