Inflatable Boat Antifouling Paint from PETTIT
Water-based, multi-season ablative antifouling paint. For hard- or soft-bottom inflatables. Cleans up with water. Black. Quart. Type: Copolymer Ablative. Recommended Usage: PVC or Hypalon; trailered boats. Biocide: CuOx 41%. Additives: No. Compatibility: With all other antifouling paints in good condition except VC-17. Number of Coats Recommended: Two.

Micron CSC Antifouling Paint, Red, Quart from INTERLUX
Haul and relaunch without loss of performance The innovative copper-copolymer formula of Micron CSC provides a controlled release of antifouling biocide at the paint surface, which means that the longevity of the coating is related to the amount of paint applied. Can be applied over most paints in good condition. Micron CSC will not lose its effectiveness when hauled out of the water for extended periods of time (such as winter storage). Type: Copolymer . 2% Cuprous Oxide . Additives: None .

Easy On Bottom Coating from OCEAN ACCESSORIES LL
Why paint when you can wax? If your boating is in low fouling fresh water or cold saltwater, consider new waxing technology instead of anti-fouling bottom paint. An easy-to-use, nontoxic, soft-wax coating for full-season protection. One bottle will cover a 24' boat. Recommended Usage: Fresh or intermittent salt water use; lasts one full season . Clear, nontoxic alternative to bottom paints . Coverage: One pint covers 24' hull . Drying Time: Dries in minutes, overnight curing before launch .

Noise Reduction Seam Tape from WEST MARINE
The 3/32" flexible vinyl sheet is fused between two layers of foam—an exterior (“decoupler”) layer and an interior (“absorber”) layer. The exterior layer is then covered with a thin film (2. 5 mil) of mylar, reinforced with elastomer-coated fiberglass, for surface heat protection and enhanced sound absorption. The overall effect is a dramatic noise reduction when compared with single-layer foam barriers. Available in two overall thicknesses. Peel and stick backing for easy installation.

Scotch General Painting Masking Tape #2050 - 2" from 3M PRODUCTS
Use in a wide range of painting applicationsGeneral-purpose. Not for critical or extended outdoor use. Recommended Usage: General purpose masking or binding tape; adheres to previously painted or varnished surfaces . Material: Crepe paper with rubber resin adhesive . Removal Time: Three days .

PVC Coated Chain, Red, 1/4" x 4' from GREENFIELD PRODUCTS
Galvanized, proof-coil anchor chain is PVC coated to protect boat surfaces. Specially formulated PVC offers excellent flexibility and durability.

WetOrDry™ Finishing Sandpaper - Ultra Fine 600 Grit, 5 Pack from 3M PRODUCTS
Ideal for wet sanding between coats of varnish, paint and other finishes. Made with silicon carbide, a sharp synthetic mineral that cuts fast and is satin smooth.

Scotchgard Marine Liquid Wax, 500ml from 3M PRODUCTS
Durable wax actually bonds to your boat's surfaceSpecial formulation uses reactive chemistry to actually bond to your boat’s surface and provide exceptionally high gloss with lasting durability. Protects gelcoat and topside coatings from damaging ultraviolet radiation, and is excellent for use on gelcoat, topside paints, painted aluminum and marine metal parts. Uses reactive chemistry to bond to your boat's surface. Exceptionally high gloss with lasting durability.

Scotchgard Marine Liquid Wax, 1Liter from 3M PRODUCTS
Durable wax actually bonds to your boat's surfaceSpecial formulation uses reactive chemistry to actually bond to your boat’s surface and provide exceptionally high gloss with lasting durability. Protects gelcoat and topside coatings from damaging ultraviolet radiation, and is excellent for use on gelcoat, topside paints, painted aluminum and marine metal parts. Uses reactive chemistry to bond to your boat's surface. Exceptionally high gloss with lasting durability.

U-1001C Top Coat Spray Catalyst - Gallon from STERLING
Spray catalyst for gloss topcoats.

Cleaner & Wax - Quart from 3M PRODUCTS
One-step processDesigned to remove light-to-medium oxidation, clean, polish and protect fiberglass gel coat and marine topside paints. A unique liquid formulation combines a compound with a special blend of waxes which restore shine and protect in one application.

Hullgard Primer Converter, Qt. from AWLGRIP
Hullgard Epoxy Primer is a holding primer that combines excellent anticorrosion and water barrier properties with anti-fouling tie-coat functionality. Suitable for below the waterline only, it offers a long overcoating interval without sanding to reduce work time along with superb adhesion to properly prepared fiberglass, steel, aluminum and wood. Can be recoated as soon as the solvents evaporate, even at low temperatures. 1 Gal. Theoretical Coverage – 140 Sq. 5 mils/135 microns DFT or 360 Sq.

Gel Coat - White, Gallon from WEST MARINE
Ideal for application of several layers, with no sanding between layers required. Use to fill gouges, chips, scrapes and deep scratches in the fiberglass gel coat. Use with PVA Curing Agent (Model 593774) to achieve full cure. Waxed Gel Coat: Superior quality isophthalic finish (non-laminating) gel coat that cures to a hard, resilient and glossy surface. Superior-quality non-laminating finish gel coat cures to a hard, resilient and glossy surface. Use to touch up worn or scratched gel coat.

Splash Zone Epoxy, #788 2GA KT from Z-SPAR COATINGS
Excellent for underwater application788 Splash Zone Epoxy Formulation: Two-part epoxy patching compound . Recommended Usage: Patching and repairing wet, damaged surfaces . Drying: One-hour working time. Four-hour set time.

Splash Zone Epoxy, #788 2QT KT from Z-SPAR COATINGS
Excellent for underwater application788 Splash Zone Epoxy Formulation: Two-part epoxy patching compound . Recommended Usage: Patching and repairing wet, damaged surfaces . Drying: One-hour working time. Four-hour set time.