Brightside Pre-Kote Primer - Gray, Quart from INTERLUX
Fills minor blemishes and sands easilyOne part primer for use with Brightside or any other one-part topside enamel. Microspheres provide high build and improved sandability. (Replaces Brightside Primer and 279 White Undercoater. ) Application: Brush, roller, airless/conventional spray . Number of Coats Recommended: One or two, depending on surface condition. Drying: Overcoating: 6 to 12 hrs. Drying Time: To touch: 1 to 3 hrs. Coverage: Brush: 112 sq. ft/qt, 450 sq. ft/gal; Spray: 87 sq.

Noise Reduction Seam Tape from WEST MARINE
The 3/32" flexible vinyl sheet is fused between two layers of foam—an exterior (“decoupler”) layer and an interior (“absorber”) layer. The exterior layer is then covered with a thin film (2. 5 mil) of mylar, reinforced with elastomer-coated fiberglass, for surface heat protection and enhanced sound absorption. The overall effect is a dramatic noise reduction when compared with single-layer foam barriers. Available in two overall thicknesses. Peel and stick backing for easy installation.

Primer Bulb, 1/4" Hose Barb from MOELLER
Primer Bulbs with hose barbs.

PVC Coated Chain, Red, 1/4" x 4' from GREENFIELD PRODUCTS
Galvanized, proof-coil anchor chain is PVC coated to protect boat surfaces. Specially formulated PVC offers excellent flexibility and durability.

Zinc Chromate Yellow Spray Primer from MOELLER
For use on aluminum and galvanized steel surfaces above or below the waterline, this primer chemically etches into aluminum and forms a corrosion-resistant surface. Helps to create an even, bondable surface for top coat adhesion. Select color (Green or Yellow) that contrasts the least with the top coat you plan to apply. 12oz.

Easy On Bottom Coating from OCEAN ACCESSORIES LL
Why paint when you can wax? If your boating is in low fouling fresh water or cold saltwater, consider new waxing technology instead of anti-fouling bottom paint. An easy-to-use, nontoxic, soft-wax coating for full-season protection. One bottle will cover a 24' boat. Recommended Usage: Fresh or intermittent salt water use; lasts one full season . Clear, nontoxic alternative to bottom paints . Coverage: One pint covers 24' hull . Drying Time: Dries in minutes, overnight curing before launch .

U-1001C Top Coat Spray Catalyst - Gallon from STERLING
Spray catalyst for gloss topcoats.

Universal Bungee with Plastic Coated Hook Ends from STARBRITE
Natural rubber core covered with polyethylene braid is rot proof, UV-resistant and long-wearing plastic coated steel hooks.

Chris Craft Stain #573 - Pint from INTERLUX
Chris Craft Stain - Pint Fills grain while staining wood, reducing the number of coats of varnish needed. May also be used on bare mahogany planking before applying primer or sanding surfacer.

Plastic Primer from RUST-OLEUM
Prepares plastic surfaces for top coating with any Rust-Oleum color or finish. For use on fiberglass, polypropylene, polystyrene, resin, PVC and hard vinyl plastics. 12oz.

Inflatable Boat Antifouling Paint from PETTIT
Water-based, multi-season ablative antifouling paint. For hard- or soft-bottom inflatables. Cleans up with water. Black. Quart. Type: Copolymer Ablative. Recommended Usage: PVC or Hypalon; trailered boats. Biocide: CuOx 41%. Additives: No. Compatibility: With all other antifouling paints in good condition except VC-17. Number of Coats Recommended: Two.

Gel Coat - White, Gallon from WEST MARINE
Ideal for application of several layers, with no sanding between layers required. Use to fill gouges, chips, scrapes and deep scratches in the fiberglass gel coat. Use with PVA Curing Agent (Model 593774) to achieve full cure. Waxed Gel Coat: Superior quality isophthalic finish (non-laminating) gel coat that cures to a hard, resilient and glossy surface. Superior-quality non-laminating finish gel coat cures to a hard, resilient and glossy surface. Use to touch up worn or scratched gel coat.

Splash Zone Epoxy, #788 2GA KT from Z-SPAR COATINGS
Excellent for underwater application788 Splash Zone Epoxy Formulation: Two-part epoxy patching compound . Recommended Usage: Patching and repairing wet, damaged surfaces . Drying: One-hour working time. Four-hour set time.

Splash Zone Epoxy, #788 2QT KT from Z-SPAR COATINGS
Excellent for underwater application788 Splash Zone Epoxy Formulation: Two-part epoxy patching compound . Recommended Usage: Patching and repairing wet, damaged surfaces . Drying: One-hour working time. Four-hour set time.

Marine-Tex Putty, Gray, 14oz. from TRAVACO
Versatile epoxy putty for wide variety of repairs Repairs damaged hulls and equipment stronger than before. Fixes gel coat chips and leaks in fuel tanks, water tanks, piping, engine blocks, cracked crank cases, etc. Can be used in working temperatures of -40° to 250°F. Marine-Tex bonds to all metals, plastics, plywood, etc. Handles like putty. Formulation: Two-part epoxy putty . Recommended Usage: Bonds to aluminum, PVC, fiberglass, most plastics, metals, glass, cement and hard/soft woods .