Gen-Sep Water Separator, 2" Diameter, Gas In/Out 2.0", Water Outlet 1.5" from CENTEK INDUSTRIES
Position the water drain from the Gen-Sep just below the water line to eliminate water splash, especially important for nighttime operation. Gen-Sep will remove nearly all of the cooling water from the exhaust. That water can then be drained to a hull fitting just below the waterline, thus eliminating excess noise often created by splashing and pulsating water flow at the exhaust outlet. A slight downward angle is required for both the exhaust outlet and the exhaust gas tube. Dimensions: 10.
|
Exhaust Bellows - Mercury - Replaces 32734A3, 18654A1 from SIERRA
Seals the exhaust/water flow from the manifold to the exhaust outlet in the drive.
|
Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .
|
Exhaust Flapper Valve - 4" from SIERRA
Heavy duty rubber flapper valve keeps following seas from entering exhaust outlet when moving slowly or stopping.
|
|
Gasket 1189-0000 from JABSCO
Jabsco gaskets & gasket kits.
|
2" ID, 90° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.
|
Series 250 Exhaust Hose, 7/8"ID, 1-3/16"OD, 565psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .
|
5" ID, 45° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.
|
|
|
Sierra-Tube-Exhaust from SIERRA
Some larger V-8 engines that create a large amount of back pressure use exhaust tubes rather than bellows. This helps to relieve the excessive pressure and eliminate problems with premature bellows failure. In the past, the exhaust bellows would blow up like a balloon and cause the drive shaft bellows to rub against the yoke and U-joints causing holes in the bellows.
|
|
|
CARB GASKET KIT from SIERRA
Sierra carb kits and gaskets for engine tune ups.
|
Windshield Screw Cover Foam, 5/8"H x 1-1/4"W x 8'L from TACO PRODUCTS
Easy do-it-yourself solution for door, windshield or hatch leaks. Specially formulated sponge rubber is engineered to withstand corrosive environments. Windshield Screw Cover Foam gives your windshield a finished look.
|
Sail Tie, Ball End 16IN, Blue from STARBRITE
Securing your mainsail to the boom is simpler and quicker when you use sail lashes instead of conventional ties. Dual lengths of durable, UV-resistant polyester plastic cord have polyethylene ball ends with brass stops and damping rings. Color-coded balls.
|
Windshield Screw Cover Foam, 1/4"H x 3/4"W x 8'L from TACO PRODUCTS
Easy do-it-yourself solution for door, windshield or hatch leaks. Specially formulated sponge rubber is engineered to withstand corrosive environments. Windshield Screw Cover Foam gives your windshield a finished look.
|
