|
|
Adjustable Packing Nut Wrench from SEAFIT
Better than a pipe wrench If you are not equipped with wrenches that fit the nuts on your stuffing box, we suggest you purchase TWO of these. Why? Because you will need two to make an adjustment: One for the locking nut and one for the adjusting nut. These wrenches tend to be easier to use than pipe wrenches—especially in tight engine spaces where many boaters must work. Primary Usage: Adjust/remove inboard shaft packing nut . Size: 1" to 3" adjustable .
|
5/16" BBB Chain, 1900lb. SWL, 7600lb. Breaking Strength, 1.2lb./ft., 550' Standard Pack from ACCO CHAIN
Bulk Chain We stock a complete selection of I. standard chain from Acco to fit almost any windlass. chain vendors. When comparing Acco chain to other brands, be sure to ask if other models are “hot-dip. ” Remember that the Safe Working Load (SWL) is a conservative rating for safety and should not be exceeded, although the breaking strength is generally 3–4 times greater. BBB is made of low-carbon steel, but has shorter, calibrated links that are designed to be compatible with many windlasses.
|
|
|
|
|
Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
|
Polycord Value Pack (10 polycords in assorted colors & lengths) from POLYFLEX
Unaffected by chemicals, sunlight, salt water and oil. Perfect for cover tie-downs, lashing jibs on deck when the chute is up, etc. Molded elastomers with glass-reinforced nylon hooks always return to original length.
|
Transom Drain Tube & Plug from MOELLER
This nylon drain tube won't rot, bend or mildew, fits flush to your transom, and allows water to drain when your vessel is trailered. A rubber O-ring makes a watertight seal. Can be loosened with a flat-head screwdriver. Fits 1 1/8'' openings. Mounted with rivets or #8 fasteners.
|
WetOrDry™ Finishing Sandpaper - Ultra Fine 600 Grit, 5 Pack from 3M PRODUCTS
Ideal for wet sanding between coats of varnish, paint and other finishes. Made with silicon carbide, a sharp synthetic mineral that cuts fast and is satin smooth.
|
Boat Vent II from TAYLOR
The newest in boat cover venting and support Don't let your interior suffer from mold and mildew damage. The patented Boat Vent II installs quickly and easily, with no screws or fasteners. The venting area provides for greater volume of exhaust air while closing the top to bottom gap - keeping water out!. The Boat Vent II is manufactured from a superior grade polycarbonate blend material for strength and UV resistance and will accommodate either 3/4" or 7/8" support poles.
|
Cabinet Handle, Stainless Steel Bar 7" from WEST MARINE
Brushed, 304 grade stainless steel pull handles feature smooth rounded ends, hidden fasteners and a stylish contemporary Euro design. Wide range of sizes available from 6 1/4" to 25" for cabinets and drawers of all sizes.
|
Uni-Fid for Splicing Braid from NEW ENGLAND ROPES
Two sizes make for neater, smoother splices. One fid is for 1/4"–3/8" line; the other is for 7/16" and larger line. Packed in a plastic storage tube.
|
CP Bronze Strap Hinge - 1.125" H x 6" W from PERKO
Chrome plated bronze. Pin Height: 1-1/8" by 6" open width. Each hinge requires six #10 fasteners.
|
300 Series Fairlead Block, Fixed Style, 2-7/32" x 3/4" from SCHAEFER
Same as the Schaefer 200 Series fairlead blocks, but with twice the working load. Use #10 fasteners. Configuration: Lead block. Sheave: UV-stabilized white Delrin®. Ball Bearings: Delrin. Sheave Size: 1-7/16" (37mm). Line Diameter: 7/16". Cheek Material/Finish: Polished stainless.
|
Stainless Strap Hinge, 2 5/8 inch from WEST MARINE
Type 304 electro-polished. Gauge: 0. 060 stainless steel. Drilled and countersunk for #8 fasteners (not included). Sold in pairs. ShWt .
|
