Auxiliary Steering Kits for Trolling Motors - Zinc Rod from MARINETECH PRODUCTS
Steer your trolling motor with your boat's main steering wheel. These connector rods attach the trolling motor directly to the main engine—when the big one moves, the little one moves along with it. Kits come complete with two quick disconnect ball joint assemblies which make taking it off when you don't need it easy. Connect rod length is 24", cut it to size for a perfect fit. Use the drive bracket for motors that have SeaStar or Teleflex steering.

Fishing Boat Cover - HS Blue 15'5"-16'4"/65" Beam from TAYLOR
Patterned to fit basic fishing boats with bench seats. (These covers are not patterned to fit over trolling motors. ) The bow and transom corners are reinforced to protect the cover from sharp aluminum edges. Poly Cotton Fabric: Trailerable 65% polyethelyne/35% cotton Breathable Mildew & Stain Resistant Water Repellant Heavy-gauge shock cord in hem 2-year limited warranty Color: Silver Gray. Hot Shot Fabric (HS): Trailerable 100% urethane-coated polyester 7.

Crab Pot Puller from ENDURANCE MARINE
This powerful workhorse makes hauling prawn and crab pots quick and easy. Designed for high-speed retrieval with a robust 1. The heavy-gauge, marine-grade aluminum frame is powder coated for corrosion-resistance and can handle loads up to 150lb. The included foot control switch provides safety, ease of use and allows both hands free to bail line. Engineered to mount on the Scotty downrigger mount #1023, Model 435050, found on page 922. Stainless-steel internal shafts, fasteners and hardware.

Gusher MKIII Cabinet-Mount Foot Pump, Right-Handed from WHALE PUMPS
This surface-mounted pump can be placed inside or outside a locker. Discharges on each stroke and self-primes (to 7' max. height). Offered in “Right” and “Left” configurations to suit installation clearance requirements. For freshwater or saltwater. gpm: 4. 3 . Dimensions: 5-1/8"H x 5"W x 3-5/8"L (excludes 4-1/8" foot pedal) .

Hot Foot Throttle Omc/Merc from T-H MARINE
Replaces your hand throttle with a foot pedal that makes you feel like you're behind the wheel of your automobile. When released, the Hot Foot automatically returns your engine to the idle position thanks to a strong stainless spring. Mounts directly to the deck of the boat and uses standard control cables. Aluminum pedal. Stainless hardware. Non-stick bearing surfaces.

Windlass Control Box/Solenoid from LEWMAR
Two-direction solenoid/control boxes designed for use with three-wire split field motors, or two-wire permanent magnet motors and three-wire series-wound motors.

Johnson/Evinrude, motor only, for 2-wire systems, 90–225hp (1991–1999) from SIERRA
Tilt/Trim Motors, Outboard Applications.

711-M28 Marine Sanitation System from SEALAND
Marine Traveler Head Complete sanitation system in one self-contained package. China bowl provides the comforts of home. Freshwater operation and Teflon seal reduce odors. Efficient unit uses less than one quart of water per flush. Water level and flushing action controlled by a single foot pedal. One-piece holding tank has 9.

Transom Trim Control from T-H MARINE
Weatherproof tilt control switch can be installed anywhere on the boat, such as back by the motor for more convenience. Can adjust trim or jack plates.

Bilge Pro Replacement Motor Cartridge for 500gph Pumps from JOHNSON PUMP
In the event of a problem, replacing your cartridge bilge pump motor is easy— provided you keep one of these on hand. Just pop out the old cartridge and pop in the new. Fit Johnson, West Marine Bilge Pro and Mayfair cartridge-style bilge and livewell pumps.

Braided Polyester Cord, by the Foot from NEW ENGLAND ROPES
A low-stretch cord that’s great for flag halyards, foredeck netting, or light-air spinnaker sheets. Sold by the foot. Diameter: 1/8". Best use: Utility cord, flag halyards . Construction: Braided polyester . Breaking strength: 530lb. . Stretch: 3% at 15% of breaking strength .

Motor Mate Lifting Davit from FORESPAR
The unit stores in its own 31" (787. Comes with tackle and will lift anything from the dinghy to the cockpit (or vice-versa) up to 100 lbs. Great for the dinghy motor, but also good for scuba tanks, ice, duffel bags, groceries, etc. The Motor Mate uses a Railfast® mounted ring on the rail and a "toe" on the cockpit coaming directly under the rail. Lightweight, portable, compact . Ideal for lifting outboard motors, sea bags, scuba gear . Lifting capacity: 100 lbs.

Whale Swim 'N' Rinse Transom Shower from WHALE PUMPS
Whale Swim 'N' Rinse Transom Shower Add the convenience of a hot and cold shower to your transom. The easy-to-install shower connects directly to the Whale Quick Connect 15 mm freshwater system. Durable, ABS plastic housing with cover hides the shower when not in use. 7' retracting hose . Water conservation control on the handset . Base plate: 6-1/2" x 11-1/2" . Allow 3-1/2" behind surface .

Aft-Deck Shower System from ATTWOOD
This compact hot/cold shower stores neatly in its own compartment on the stern or in the head. Includes a handheld shower spray head with shutoff, 6' hose, hot/cold water controls and a cover. Easily hooked into your freshwater system. Compartment is drilled for six #8 fasteners. Material: High-impact plastic . Dimensions: 9-1/2"H x 5"W x 2-1/4"D . Hose Size: 6'L . Port Sizes: 1/2" NPT .

Stern Rail Outboard Motor Mount for 1" Railing from EDSON CORPORATION
Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with nonskid pad, bolted to the UV stable poly backing board always looks shipshape. no more varnishing. Comes complete with hardware to attach to any standard 1'' (2. 5cm) stainless rail. Warning: Be sure the engine is securely tied onto the backing board and the engine mounts are tightened whenever the engine is stored on Edson's Outboard Motor Mount.