316 Stainless-Steel Hose Clamp, 7/16" to 11/16", SAE Size 3 from ABA OF AMERICA
Hose clamps you can trust now and later Trust these clamps for secure hose connections. All components are Type 316 stainless steel for ultimate corrosion resistance. The smooth, unperforated band surface and rolled edges prevent hose damage. Band and screw threads are properly pitched, rendering the clamp virtually immune to vibration-caused back-off. Hoses are measured by inside diameter, so use a clamp with a maximum opening at least a 1/4" larger .
|
Barb, 5/16" Brass Hose Mender from MOELLER
Each hose mender includes two (2) Stainless Steel Clamps.
|
Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .
|
Electric Bilge Pump Installation Kit from ANCOR MARINE
Essential items for installing a bilge pump Convenient package includes four #8 x 3/4" stainless-steel panhead screws, one 1-3/4" x 3/4" stainless steel hose clamp, and three 16-14AWG heat shrink butt connectors.
|
304 Stainless-Steel Hose Clamp, 3-1/8" to 4", SAE Size 56 from NORMA
With 9mm-wide (3/8") non-perforated bands, and made of stainless steel, these clamps feature rolled-up edges to prevent hose damage. We recommend two clamps per hose end below the waterline. Hoses are measured by inside diameter, so select a clamp with a maximum opening at least 1/4" larger. Designed to evenly distribute tension force . Work well in many different applications with a high mechanical load .
|
Mast Boot Fitting Mast to 23", Collar Size to 37" from SAILING SPECIALTIES, INC.
Easily installed over stepped masts by slitting one side, trimming to fit, and gluing with adhesive supplied. Secure with stainless hose clamps. May not fit rectangular wooden masts. Flexible, UV-resistant plastic.
|
Gas Fill & Tank Vent - Black from PERKO
Perko Gas Fill and Tank Vent This ingenious plastic deck fill has a vent with a flame arrestor built right into the fill flange. A flip-up cap eliminates the need for a deck key and no ground wire is required.
|
711-M28 Marine Sanitation System from SEALAND
Marine Traveler Head Complete sanitation system in one self-contained package. China bowl provides the comforts of home. Freshwater operation and Teflon seal reduce odors. Efficient unit uses less than one quart of water per flush. Water level and flushing action controlled by a single foot pedal. One-piece holding tank has 9.
|
Series 315 Outboard Fuel Hose - 3/8"ID from SHIELDS RUBBER
Premium-quality fuel hose designed for outboard feed and vent lines. Remains flexible at low temperatures and resists UV sunlight. Silverado 2000 complies with SAE J1527 Type B2 specifications. Should not be used in applications requiring the use of Type B1 fuel feed line.
|
Series 250 Exhaust Hose, 7/8"ID, 1-3/16"OD, 565psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .
|
|
|
Fuel Hose, Type B-2 5/16" from MOELLER
We offer 5/16" and 3/8" SCG B-2 alcohol-resistant hose as used in pre-assembled fuel line. Sold by the foot.
|
Low-Permeation Fuel Hose, 1/2" ID, 250' Max. Length from SHIELDS RUBBER
Special design NBR tube with an embedded plastic barrier layer limits permeation. The design of this hose provides easy coupling insertion and the NBR/PVC cover is weather and UV resistant. The hose is also polyester reinforced and fire-resistant. Fuel Type: Fuel feed (gasoline up to 85% ethanol blended fuels/diesel/bio-diesel all blends) . Approvals: SAE J1527 Type A1-15 and ISO 7840 Type A1 . Construction: Reinforced with high strength synthetics to resist gasoline/alcohol permeation .
|
WM Self-Coiling Hose - 15' from WEST MARINE
Featuring an improved flow rate and field-serviceable couplings! With an improved flow rate of 360gph, this hose delivers a powerful stream of water to make deck and boat wash-downs quick and easy. In the unlikely event of a rupture, the couplings can be removed with common hand tools, the hose shortened and the couplings replaced, which is a big advantage if you happen to be offshore! 90% usable length. Field-serviceable couplings. Strain relief at hose connection end'. 360gph flow rate.
|
|
|
