Replacement Ball Bearings for 150 Cam Cleat from HARKEN
Harken Cam-Matic cleats are legendary for smooth operation when holding and releasing control lines. Three rows of Delrin ball bearings allow the jaws to open and close smoothly under the highest loads. Light springs allow the cleats to open freely, so the teeth do not have to be sharp which means that your line lasts longer. Use models with aluminum jaws for high loads, or when the line will be drawn through the teeth for adjustment.

Yellow Medium C-Cleat from RONSTAN
Reversible jaws effectively double the life of the cleat and are kind to expensive line, yet grip tenaciously. Beveled cam tops and low spring effort require minimum force when inserting line. Self-lubricating, self-cleaning slotted bearings are impregnated with Teflon®, provide lower frictional resistance and quicker response than ball bearings, which deform under load. Rope Guides: This fairlead, mounted on the load side of the cleat, assures correct alignment of control lines in the cleat.

Trapeze & Vang Cleat from CLAMCLEAT
The cleat has an in-built pulley that offers a compact solution for rigging with a 1:1 or 2:1 advantage, where a quick, positive lock that is easy to release is required. The sailor's preferred choice for adjusting trapeze lines.

XA/XAS, Replacement Cam Kit from SPINLOCK
Cam Replacement & Upgrade Kits for XTS Powerclutches.

4.5" Stainless-Steel Pop-Up “Neat Cleat” from ATTWOOD
Retractable stainless steel cleats retract to only 1/2" above deck and have direct drainage to the bilge. Corrosion-free. Install easily. Hardware included. Functions: Drains to bilge with drainage receptacle. Requires 3/8" ID tube (not supplied) . Material: Stainless steel . Height: Lowered, 1/2"; Raised, 1-5/8" . Line Size: 1-1/4" line opening . Cutout Size: 7/8" hole saw size. Max.

Cleat, European Jam from WEST MARINE
Strong nylon jam cleat commonly found on most European boats.

Midrange Hexaratchet Ratchet Block, Single, 1,800lb. SWL, 14oz. from HARKEN
Stronger versions of the Hexaratchet II+2 with 8:1 holding power. Beefier posts and wraparound straps handle higher working loads. Sheave: Teflon-impregnated Hardkote anodized aluminum. Bearings: Delrin. Sheave Size: 3" (76mm). Line Diameter: 9/16" max. Cheek Material/Finish: Plastic with wrap-around stainless straps. Shackle/Strap Type: Heavy-duty forged swivel with three-way head; locks or rotates. Cleat: 1556 and 1566: 280 Cam-Matic.

RigTune Pro Digital Rig Tension Gauge from HARKEN
Old-fashioned spring gauges, like the Loos Pro, don’t provide repeatable numbers. This product does. Unlike spring-loaded gauges, the Harken Rigtune Pro measures rig tension to the nearest kilogram. A load cell records the pressure on one of the pins and the measurement is displayed on a simple, easy-to-read screen. The Rigtune Pro fits a specific range of rigging sizes, 2. As rigging is deflected over three pins on the back of the gauge, a load cell records the pressure on one of the pins.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

Lateral Starboard Clamcleat, 1/4"–3/8" Rope Dia., 3/16"H x 2"W x 2-7/8"L, 1/4" Fasteners from CLAMCLEAT
.

Offset Threaded Shaft Cam Bar from PERKO
Spare offset threaded shaft cam bar for your surface mount lock & latch set.

60mm Racing Fiddle Block with Becket & Cleat, 882lb. SWL, 12.4oz. from LEWMAR
For chafe-free, low-friction tackles. Sheave: Anodized aluminum alloy . Ball Bearings: Delrin® . Sheave Size: 2-3/8" (60mm) & 1-5/8" (40mm) . Line Dia. : 3/8" max. . Cheek Material/Finish: Anodized aluminum alloy . Shackle/Strap Type: Swivel with three-way locking, drilled-out head . Cleat: Model with cleat: adjustable arm, aluminum cam cleat .

29mm Carbo Clew Block Assembly from HARKEN
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.

Spinnaker Pole Car, Track #2720, 900sq.ft. Max. Sail Area, 1125lb. SWL from HARKEN
Now with captive ball bearings, which eliminates the need for a ball-bearing loader during installation or removal from track. These cars run freely, fit low-beam traveler track and are easy to adjust under any load.

Winch Service Kit from HARKEN
Contains 10 pawls and 10 springs.