81cm Fiberglass Seat for RIB 350 Inflatable Boat from WEST MARINE
Inflatable Boat Seats.

Exhaust Bellows - Mercury - Replaces 32734A3, 18654A1 from SIERRA
Seals the exhaust/water flow from the manifold to the exhaust outlet in the drive.

Fits all Cobra. Replaces OMC 914036 from SIERRA
Seals the exhaust/water flow from the manifold to the exhaust outlet in the drive.

Contura Rocker Switch, SPDT On/Off/On from COLE HERSEE
Waterproof switches are rated to IP66 for use on ship decks and with an LED light to indicate when the circuit is on. Several configurations are available for almost any application. Recommended for replacements in waterproof electrical panels with rocker switches to ensure waterproof integrity. Includes both black and gray covers. Both switches and covers are interchangeable with similar switches used as original equipment on many common boat types. Mounting Hole Size: 1. 450" x 0.

Sierra-Tube-Exhaust from SIERRA
Some larger V-8 engines that create a large amount of back pressure use exhaust tubes rather than bellows. This helps to relieve the excessive pressure and eliminate problems with premature bellows failure. In the past, the exhaust bellows would blow up like a balloon and cause the drive shaft bellows to rub against the yoke and U-joints causing holes in the bellows.

Fiberglass Boat Cleaner 920 1/2 Gallon from COLLINITE
Removes rust, exhaust, oil, grease, and oxidation stains from fiberglass. Restores the original color quickly without hard rubbing or buffing, leaves a chemically clean surface to which waxes can bond. Use with fiberglass boat wax or heavy-duty paste Fleetwax . Made in U. S. A.

2" ID, 90° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

5" ID, 45° Marine Rubber Exhaust Elbow from SHIELDS RUBBER
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.

Inflatable Boat Ladder from GARELICK
Contoured to hug the hull of inflatable boats. Attaches to floorboard or side with 3/8'' line and heavy-duty swivel snap. 1'' dia. anodized aluminum tubing with plastic rungs. Vinyl sleeves protect hull fabric.

Walker Bay 10, 9'8" Length, 4'9" Beam, 126lb., 449lb. Capacity (up to 3 people) from WALKER BAY BOATS
Bolt in the seats, break out the oars (or optional sail kit or motor) and you’re ready to cast off. Boats include exclusive Hydro-Curve Oars. Application: Rowing, motoring or sailing . Hull Material: High Impact Polypropylene . Construction: High-pressure injection molded . Hull Shape: Round bottom lapstrake-style . Standard Hardware: Oars, oar locks, seats, stainless bow eye, Wheel in the Keel™ . Available Accessories: Sail kits, RID kits, Bimini boat cover . Warranty: 10 years limited.

Off/1/All/2 Battery Switch, 380 Continuous Amps, 850 Intermittent Amps from PERKO
For high-amperage applications like diesel engine starters, large inverters and windlasses. Reinforced polycarbonate body, 1/2"dia. brass terminal connections and an alternator field disconnect. Alt. Field Disc. : Yes . Switch Material: Reinforced Polycarbonate. Terminal Material/Size: Brass 1/2"dia. . Switch Dimensions: 5-1/4"sq. x 3-3/8"H .

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

Tubing-Alu 7/8X20' from WEST MARINE
Bright 304 polished stainless steel or bright anodized aluminum. Used for a multitude of applications including grab rails, bow rails, and canvas top frames. Match materials between components to minimize corrosion. Stainless has . 049" wall thickness . Aluminum has . 058" wall thickness . Use 7/8" tubing for smaller powerboats . Use 1" tubing for sailboats and larger powerboats . Available in 6', 12' and 20' lengths .

Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Exhaust Flapper Valve - 4" from SIERRA
Heavy duty rubber flapper valve keeps following seas from entering exhaust outlet when moving slowly or stopping.