Eisenglass & Plastic Restoration Kit from FLITZ
Restore clarity to yellow, hazy or cloudy eisenglass, Plexiglass, plastics, gelcoat and fiberglass the fast and easy way with this kit. Kit includes: 7" diameter. Washable Flitz Buffing Ball for use with any 3/8" drill motor. 1. 76oz. tube Flitz Metal, Fiberglass & Plastic Polish. 1. 7oz.

Polyethelene/Royalex Repair Kit from OCEAN KAYAK
Repair cracks or holes in your polyethylene or Royalex kayak. Complete kit includes everything you need to touch up your boat’s surface. Repair material. Adhesive and finishing solution. Wood stir stick. 2" paint brush.

Kayaker's Fishing Toolbar from CONFLUENCE HOLDINGS
It's a fisherman's utility belt for your kayakUnique, pre-slotted attachment bar allows you to mount a variety of accessories including rod holders, fishfinders, compasses, GPS units or lights securely to your kayak without having to mount them permanently. Features nylon straps for attaching to most standard deck loops, making it easy set up or remove. It adjusts to fit almost any kayak and can be cut down to match the width of narrower singles. Rubber feet protect and stick to decks.

Tubing-Alu 7/8X20' from WEST MARINE
Bright 304 polished stainless steel or bright anodized aluminum. Used for a multitude of applications including grab rails, bow rails, and canvas top frames. Match materials between components to minimize corrosion. Stainless has . 049" wall thickness . Aluminum has . 058" wall thickness . Use 7/8" tubing for smaller powerboats . Use 1" tubing for sailboats and larger powerboats . Available in 6', 12' and 20' lengths .

Auxiliary Steering Kits for Trolling Motors - Zinc Rod from MARINETECH PRODUCTS
Steer your trolling motor with your boat's main steering wheel. These connector rods attach the trolling motor directly to the main engine—when the big one moves, the little one moves along with it. Kits come complete with two quick disconnect ball joint assemblies which make taking it off when you don't need it easy. Connect rod length is 24", cut it to size for a perfect fit. Use the drive bracket for motors that have SeaStar or Teleflex steering.

Johnson/Evinrude, motor only, for 2-wire systems, 90–225hp (1991–1999) from SIERRA
Tilt/Trim Motors, Outboard Applications.

Sierra-Tube-Exhaust from SIERRA
Some larger V-8 engines that create a large amount of back pressure use exhaust tubes rather than bellows. This helps to relieve the excessive pressure and eliminate problems with premature bellows failure. In the past, the exhaust bellows would blow up like a balloon and cause the drive shaft bellows to rub against the yoke and U-joints causing holes in the bellows.

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.

Transom Drain Tube & Plug from MOELLER
This nylon drain tube won't rot, bend or mildew, fits flush to your transom, and allows water to drain when your vessel is trailered. A rubber O-ring makes a watertight seal. Can be loosened with a flat-head screwdriver. Fits 1 1/8'' openings. Mounted with rivets or #8 fasteners.

Bilge Pro Replacement Motor Cartridge for 500gph Pumps from JOHNSON PUMP
In the event of a problem, replacing your cartridge bilge pump motor is easy— provided you keep one of these on hand. Just pop out the old cartridge and pop in the new. Fit Johnson, West Marine Bilge Pro and Mayfair cartridge-style bilge and livewell pumps.

Motor Mate Lifting Davit from FORESPAR
The unit stores in its own 31" (787. Comes with tackle and will lift anything from the dinghy to the cockpit (or vice-versa) up to 100 lbs. Great for the dinghy motor, but also good for scuba tanks, ice, duffel bags, groceries, etc. The Motor Mate uses a Railfast® mounted ring on the rail and a "toe" on the cockpit coaming directly under the rail. Lightweight, portable, compact . Ideal for lifting outboard motors, sea bags, scuba gear . Lifting capacity: 100 lbs.

Stern Rail Outboard Motor Mount for 1" Railing from EDSON CORPORATION
Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with nonskid pad, bolted to the UV stable poly backing board always looks shipshape. no more varnishing. Comes complete with hardware to attach to any standard 1'' (2. 5cm) stainless rail. Warning: Be sure the engine is securely tied onto the backing board and the engine mounts are tightened whenever the engine is stored on Edson's Outboard Motor Mount.

Stern Rail Outboard Motor Mount - Aluminum for 1-1/4" Railings from EDSON CORPORATION
Built to hold motors up to 15 hp or 100 lbs/45 kg. Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with non-skid pad, bolted to the UV stable poly backing board always looks ship-shape… no more varnishing. Bottom cleat comes unattached so that it will fit any rail spacing. Note: 1-1/4” rail version comes complete with anodized aluminum bracket, stainless cleat and stainless U-bolt for 1-1/4” railing.

Nova Lift™ from FORESPAR
Forespar's Nova Lift products combine elegant styling with superb strength and function. Other brands swing left and right without control. Nova Lift comes with a stainless-steel lower mounting tube that will accommodate 30" height rails. Vessels with rails higher than 30" will require the use of a deck pad (not included) to raise the installation to the proper height. The Nova Lift with Winch is ideal for trawlers and motor yachts where sailboat winches are not available. 220 lbs.