Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

5/8" Stainless-Steel Sail Track Stop from SCHAEFER
Stainless-steel end stops protect your sails.

1-1/2" Traveler Track End Stop from SCHAEFER
Stop-End Traveler 1. 5in|Stop-End Traveler 1.

Spinnaker Pole Car, Track #2720, 900sq.ft. Max. Sail Area, 1125lb. SWL from HARKEN
Now with captive ball bearings, which eliminates the need for a ball-bearing loader during installation or removal from track. These cars run freely, fit low-beam traveler track and are easy to adjust under any load.

Marine Dry Lube from CRC MARINE
Superior dry lubrication for moving or stationary parts. Displaces moisture and inhibits corrosion. Fortified with PTFE to provide a micro-thin film that won’t attract dust or dirt. Dries in seconds. Will not stain sails or clothes. Great for mast track, genoa or traveler T-track, headsail grooves, hinges, zippers, headfoils, and sliders.

Hi-Load Ti-Lite Car, Torlon Bearings, 850lb. SWL from HARKEN
These lightweight, solid aluminum and compact captive ball (CB) travelers are built to handle very high loads. Captive ball bearings let you roll the cars on and off the track without using a ball loader. Boat Size: Dinghies, multihulls, to small offshore boats. Material: One-piece solid aluminum . Shackle: Pivoting toggle models—fasten control blocks directly to post without needing a shackle. Sheave: Fixed sheave models—mainsheet loads 40° or less from vertical.

Snap Furl CF-700 Furling System from SCHAEFER
" Small boat furler comparison, Practical SailorSnapFurl systems come in two sizes to accommodate boats 16' to 24' and boats 24' to 28' and represents the latest in quality Schaefer design and engineering. The efficient Round Geon™ PVC foil snaps quickly and easily around your boat’s existing headstay without the need for special tools or modifications to the rig. System SnapFurl CF-500 for Boats 16’ to 24’ (4. Long fiber reinforced injection molded components make SnapFurl CF 500 unique.

Tubing-Alu 7/8X20' from WEST MARINE
Bright 304 polished stainless steel or bright anodized aluminum. Used for a multitude of applications including grab rails, bow rails, and canvas top frames. Match materials between components to minimize corrosion. Stainless has . 049" wall thickness . Aluminum has . 058" wall thickness . Use 7/8" tubing for smaller powerboats . Use 1" tubing for sailboats and larger powerboats . Available in 6', 12' and 20' lengths .

G. O'Day 222/Santana 525,Length 47", Height at tip 2 1/4", Width at butt 1 1/2", Width at tip 2" from WEST MARINE
Replace that old ugly tiller with a new hand-made laminated ash and mahogany wood tiller, made to fit your rudder hardware, and pre-finished with multiple coats of premium marine spar varnish. Choose the right length and profile, and the butt-end measurements to fit your rudderhead hardware. Can’t find a good fit? Idasailor Marine can custom-build a tiller to your measurements . Custom tillers are shipped direct within 10 days . Click HERE to open the PDF custom order form.

6" Polished Aluminum Flip Up Dock Cleat from DOCK EDGE INC
These sleek, low-profile cleats fold down and out of the way when not in use. The smooth rounded surfaces are made of solid aluminum with a white polyester power coating. Predrilled for mounting with 3/8" carriage bolts (hardware sold seperately). .

4.5" Stainless-Steel Pop-Up “Neat Cleat” from ATTWOOD
Retractable stainless steel cleats retract to only 1/2" above deck and have direct drainage to the bilge. Corrosion-free. Install easily. Hardware included. Functions: Drains to bilge with drainage receptacle. Requires 3/8" ID tube (not supplied) . Material: Stainless steel . Height: Lowered, 1/2"; Raised, 1-5/8" . Line Size: 1-1/4" line opening . Cutout Size: 7/8" hole saw size. Max.

Furling Lead Block from RONSTAN
A sleek, snag-free way to lead your furler's lines back to the cockpit. Clamps around the 7/8" or 1" stanchion tubing, so you don't have to drill any holes.

Single Channel-Mate Glass Channel, 7/16"W from BECKSON MARINE
This window track is ideal for window glass or for installing sliding cabinet doors. Each channel groove is slightly (. 005") narrower than 1/4" window glass so there is positive pressure against the glass at all times. It seals out leaks and prevents glass from rattling. Made of B-FLEX marine plastic, it will not crack or discolor. The elevated slide at the bottom of the channel makes windows or doors easy to open and close. Sold in 8' lengths.

WL/1 Fairlead Model from SPINLOCK
New low-profile design easily mounts to 1" stanchion using internal clamping system. WL/2 sheave model utilizes unique tracker ball angle adjustment. WL/1 Fairlead model includes stainless-steel bullseye for strength.

Ring Style Car RC-125 from FORESPAR
Separates the up/down and side-to-side motions of the pole to make a bind-free, strong attachment. Shackles are supplied for uphaul/downhaul lines. Stainless steel cheeks, aluminum body and plastic liners. Ring Style Car RC-125 Although a screw-pin stop is supplied, this car is designed to be used with uphaul/downhaul blocks shackled to the bails at each end. Ring ID: 1 5/8". Investment cast stainless steel with plastic liners to reduce friction. Fits UXP and UTR pole end fittings.