Auxiliary Steering Kits for Trolling Motors - Zinc Rod from MARINETECH PRODUCTS
Steer your trolling motor with your boat's main steering wheel. These connector rods attach the trolling motor directly to the main engine—when the big one moves, the little one moves along with it. Kits come complete with two quick disconnect ball joint assemblies which make taking it off when you don't need it easy. Connect rod length is 24", cut it to size for a perfect fit. Use the drive bracket for motors that have SeaStar or Teleflex steering.

225 Series, 10 Micron Spin-On Replacement Element from RACOR-PARKER FILTRAT
For Racor Spin-On Series Diesel Fuel Filter/Water Separators.

300 Series Fairlead Block, Fixed Style, 2-7/32" x 3/4" from SCHAEFER
Same as the Schaefer 200 Series fairlead blocks, but with twice the working load. Use #10 fasteners. Configuration: Lead block. Sheave: UV-stabilized white Delrin®. Ball Bearings: Delrin. Sheave Size: 1-7/16" (37mm). Line Diameter: 7/16". Cheek Material/Finish: Polished stainless.

Series 60 Orbit Block, Single Light-Load, 2-3/8" Sheave Size, 1,710lb. SWL, 4.7oz. from RONSTAN
These exceptionally strong blocks feature the performance Orbit sheave with captive Acetal ball bearings for side thrust loads, eliminating the need for side retainer plates. The 75mm webbing block (RF79107) can be used where swivel head and shackle attachment is not required to achieve further weight savings. Sheave Size: 2-3/8" (60mm) or 3" (75mm). Line Diameter: Series 60: 1/2" (12mm), Series 75: 9/16" (14mm). Cheek Material/Finish: Anodized aluminum.

Johnson/Evinrude, motor only, for 2-wire systems, 90–225hp (1991–1999) from SIERRA
Tilt/Trim Motors, Outboard Applications.

Series 40 Ratchet Block, Single/Cleat, 385lb. SWL, 3.4oz. from RONSTAN
Practical Sailor's Ratchet Block Click-Off rated Ronstan's Orbit block "Overall, the most impressive with its grip, versatility, and lightweight design. " The newest addition to Ronstan’s Orbit range of super lightweight, fiber-reinforced blocks. Ideal for sheet applications on dinghies up to 16' and control line applications for small keel boats. There are two styles of Series 40 ratchet blocks. Many of the top Grand Prix Laser sailors are switching to Orbit blocks.

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Bowl Drain Valve, 900/1000 Series from RACOR-PARKER FILTRAT
Parts for 500, 900 and 1000 Turbine Series Filters.

Bilge Pro Replacement Motor Cartridge for 500gph Pumps from JOHNSON PUMP
In the event of a problem, replacing your cartridge bilge pump motor is easy— provided you keep one of these on hand. Just pop out the old cartridge and pop in the new. Fit Johnson, West Marine Bilge Pro and Mayfair cartridge-style bilge and livewell pumps.

Motor Mate Lifting Davit from FORESPAR
The unit stores in its own 31" (787. Comes with tackle and will lift anything from the dinghy to the cockpit (or vice-versa) up to 100 lbs. Great for the dinghy motor, but also good for scuba tanks, ice, duffel bags, groceries, etc. The Motor Mate uses a Railfast® mounted ring on the rail and a "toe" on the cockpit coaming directly under the rail. Lightweight, portable, compact . Ideal for lifting outboard motors, sea bags, scuba gear . Lifting capacity: 100 lbs.

Stern Rail Outboard Motor Mount for 1" Railing from EDSON CORPORATION
Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with nonskid pad, bolted to the UV stable poly backing board always looks shipshape. no more varnishing. Comes complete with hardware to attach to any standard 1'' (2. 5cm) stainless rail. Warning: Be sure the engine is securely tied onto the backing board and the engine mounts are tightened whenever the engine is stored on Edson's Outboard Motor Mount.

Stern Rail Outboard Motor Mount - Aluminum for 1-1/4" Railings from EDSON CORPORATION
Built to hold motors up to 15 hp or 100 lbs/45 kg. Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with non-skid pad, bolted to the UV stable poly backing board always looks ship-shape… no more varnishing. Bottom cleat comes unattached so that it will fit any rail spacing. Note: 1-1/4” rail version comes complete with anodized aluminum bracket, stainless cleat and stainless U-bolt for 1-1/4” railing.

OSCO GASKET FOR 274147 from OSCO MOTORS CORP.
Fits Osco Motors # 8125 manifold .

Fishing Boat Cover - HS Blue 15'5"-16'4"/65" Beam from TAYLOR
Patterned to fit basic fishing boats with bench seats. (These covers are not patterned to fit over trolling motors. ) The bow and transom corners are reinforced to protect the cover from sharp aluminum edges. Poly Cotton Fabric: Trailerable 65% polyethelyne/35% cotton Breathable Mildew & Stain Resistant Water Repellant Heavy-gauge shock cord in hem 2-year limited warranty Color: Silver Gray. Hot Shot Fabric (HS): Trailerable 100% urethane-coated polyester 7.

Tachometer/System Check (4"), Johnson/Evinrude outboard, 7000RPM from FARIA INSTRUMENTS
For more than 50 years, Faria has lived up to its reputation as a producer of high-quality, long-lasting instruments. The immensely readable and durable instruments in the Euro series feature bold, bright white numerals against a non-glare black background. Sculpted white pointers and low-profile black aluminum bezels make for even greater readability. Features a perimeter-lit black dial and flat glass lens.