Stainless-Steel Rub Rail, End, 1"H x 12"L; Requires #8 Screws from TACO PRODUCTS
Fits a wide variety of vinyl profiles Hollow back (marine grade type 304) has concave back to fit rigid vinyl rub rails and provide added protection and chrome-like accent around entire boat. Most widely used stainless-steel inserts fit the largest variety of vinyl profiles on the market. Solid back stainless-steel rub rail provides premium heavy-duty protection and a polished finish for your boat.

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Rail Mount Outboard Bracket, 10 1/2" from WEST MARINE
Keep your small outboard safe and upright on the stern rail, rather than stowed in a locker where gasoline from the tank could cause hazardous fumes to collect, or spill and ruin stored goods. Two-piece mounting blocks clamp around a 1'' O. D. rail ''T''. Holds outboards up to 8 hp. Each comes complete with stainless mounting bolts. UV-stabilized polypropylene.

Transom Drain Tube & Plug from MOELLER
This nylon drain tube won't rot, bend or mildew, fits flush to your transom, and allows water to drain when your vessel is trailered. A rubber O-ring makes a watertight seal. Can be loosened with a flat-head screwdriver. Fits 1 1/8'' openings. Mounted with rivets or #8 fasteners.

Rubrail Insert - for Style #6, Model 341100 from TACO PRODUCTS
Rubber inserts add cushioning to your aluminum rubrails. . These fit styles #5, #6 and #7. Rub rails and inserts sold separately. .

Rail Mount Anchor Bracket, Horizontal from WINDLINE
Stow your anchor up off the deck, ready for instant deployment. These brackets hold fluke-style Danforth, West Marine, U. S. anchors up to 35lb. and all Fortress anchors (except those with mud palms).

Insert - for Taco #V21-9517, #V21-9501, #V21-9602, Per Foot from TACO PRODUCTS
Rubber inserts add cushioning to your aluminum rubrails. . These fit styles #5, #6 and #7. Rub rails and inserts sold separately. .

Lube Tube Adapter for Yamaha, Nissan, Tohatsu, Honda (2-50hp) from WEST MARINE
Marine lower unit drain, flush and fill tool. Metal threaded fitting fits MerCruiser, OMC, Evinrude, Johnson, Honda (70-90hp), Volvo, Force and Gamefishier lower units. Quick, easy and clean way to change marine lower unit gear lube. For use with all 8- and 10-oz.

Fluke-Style Anchor Rail Mount from SCHAEFER
Safe off-the-deck stowage for Danforth-style anchors to 22lb. This anchor mount enables secure, off-the-deck storage and quick deployment of Danforth style anchors from 8-22 pounds. Mounts onto 1" diameter horizontal bow or stern rails and features a quick release mechanism with a locking hole to prevent accidental release. Closing latch enables one hand anchor engagement. 304 stainless steel.

Transom Drain Tube - 1 x 3" from SEAFIT DRAIN
Corrosion resistant brass.

Sierra-Tube-Exhaust from SIERRA
Some larger V-8 engines that create a large amount of back pressure use exhaust tubes rather than bellows. This helps to relieve the excessive pressure and eliminate problems with premature bellows failure. In the past, the exhaust bellows would blow up like a balloon and cause the drive shaft bellows to rub against the yoke and U-joints causing holes in the bellows.

Stern Rail Outboard Motor Mount for 1" Railing from EDSON CORPORATION
Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with nonskid pad, bolted to the UV stable poly backing board always looks shipshape. no more varnishing. Comes complete with hardware to attach to any standard 1'' (2. 5cm) stainless rail. Warning: Be sure the engine is securely tied onto the backing board and the engine mounts are tightened whenever the engine is stored on Edson's Outboard Motor Mount.

Stern Rail Outboard Motor Mount - Aluminum for 1-1/4" Railings from EDSON CORPORATION
Built to hold motors up to 15 hp or 100 lbs/45 kg. Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with non-skid pad, bolted to the UV stable poly backing board always looks ship-shape… no more varnishing. Bottom cleat comes unattached so that it will fit any rail spacing. Note: 1-1/4” rail version comes complete with anodized aluminum bracket, stainless cleat and stainless U-bolt for 1-1/4” railing.

Nova Lift™ from FORESPAR
Forespar's Nova Lift products combine elegant styling with superb strength and function. Other brands swing left and right without control. Nova Lift comes with a stainless-steel lower mounting tube that will accommodate 30" height rails. Vessels with rails higher than 30" will require the use of a deck pad (not included) to raise the installation to the proper height. The Nova Lift with Winch is ideal for trawlers and motor yachts where sailboat winches are not available. 220 lbs.

ADJ 7-15-DL Whisker Pole, 83"/9lb. Collapsed Length/Weight, 202" Max. Working Length, 2" Tubing Diameters from FORESPAR
These telescoping whisker poles are heavy-duty two-section and three-section aluminum spars which can be extended to lengths up to 17' and securely locked in position by an internal twist lock device. Poles feature self-latching Ultra Series™ fittings on the inboard and outboard ends. Aluminum tubing. End Fitting Inboard: UPX. End Fitting Outboard: UPX.