Flush Lock - Black/Stainless Steel with Adjustable Offset Cam Bar from PERKO
Black plastic with stainless steel "D" ring handle and with adjustable offset cam bar. Two O-rings for increased water resistance. Position indicator shows open or closed position. Door thickness: 3/8" to 1-14" . Face plate dimensions: 2-7/8" x 2-7/8" . Adjustment latch bar: 3/8" to 3" .

8-1/2" Hatch Holder, Adjustable, for Hatches to 10lb. from MOONLITE MARINE
Stainless, spring-type holders “pop” into place to hold hatches, doors, table leaves, etc. Easy to install. Adjustable model allows opening between 10° and 80°.

Horizontal Chrome/Brass Masthead Light, Boat Size to 12m (39'4"), 2-3/8"H x 7/8"W from PERKO
For powerboats and sailboats. Chrome-plated brass or chrome-plated zinc. Mounting Hardware: #4 FHMS Volts: 12V Draw: 0.

Adjustable Packing Nut Wrench from SEAFIT
Better than a pipe wrench If you are not equipped with wrenches that fit the nuts on your stuffing box, we suggest you purchase TWO of these. Why? Because you will need two to make an adjustment: One for the locking nut and one for the adjusting nut. These wrenches tend to be easier to use than pipe wrenches—especially in tight engine spaces where many boaters must work. Primary Usage: Adjust/remove inboard shaft packing nut . Size: 1" to 3" adjustable .

Capstan 1000 Rope Winch from POWERWINCH
Versatile system uses an easy to operate foot switch to retrieve anchors or fishing pots or provide power assistance on limited crew sailboats. Solid, 1-piece, machined capstan features aluminum housing with stainless steel internal shafts and hardware. Deck mounted design saves space for rope locker. Mounting template included. Pulling Power: 1000lbs. Speed Up: 40'/min. Boat size: to 55' . Rope Type: 3-strand nylon. Draw: 27A @12v. Measure 6 5/16"H x 8"W x 10 9/16"L.

Starboard Side Green Vertical-Mount Side Navigation Light, 3-5/8”H x 4-1/8”W from PERKO
European style Series 170 side navigational lights are certified for use on powerboats and sailboats up to 20m (or 65. 6') with 12V electrical systems. Red or green lenses with 12V bulbs included. 2nm visibility range. Case Material: Chrome-plated brass tops with black plastic bases . Mounting Hardware: #10 FHMS (sold separately) . Volts: 12V . Draw: 0. 97A . Replacement Bulb: Model 8646853 .

TankWatch® 4 Water/Holding Tank Monitor from SEALAND
Reliable micro float switches activate empty, low, mid and full tank levels on the indicator panel. No electrical components contact water or waste. Easy to install using universal flange (sold separately). Includes cap with micro float switches . Indicator panel . Gasket and stainless mounting hardware . Adapts to fit any water or holding tank up to 22" . 45" adjustable probes available by Special Order .

Vertical Sidelights, White from PERKO
For powerboats and sailboats less than 20m or 65. 6'. Plastic frames with ultrasonically welded lenses and gasketed plastic bases. 2nm visibility. Per pair, except bi-color. Case Material: Plastic . Case Dimensions: 3-1/2"L x 2-1/4"W x 13/16"H . Mounting Hardware: #8 FHMS (sold separately) . Volts: 12V . Draw: 0. 7A .

Flat Cam Riser, 1"H from HARKEN
Harken Cam-Matic cleats are legendary for smooth operation when holding and releasing control lines. Three rows of Delrin ball bearings allow the jaws to open and close smoothly under the highest loads. Light springs allow the cleats to open freely, so the teeth do not have to be sharp which means that your line lasts longer. Use models with aluminum jaws for high loads, or when the line will be drawn through the teeth for adjustment.

Adjustable Lock from TAYLOR
Three-part system provides easy snap-on/snap-off fender attachment and adjustment. A stainless base mounts to your boat, into which a peg snaps to hold the fender strap (sold separately). Fixed peg requires tying a knot to secure the fender at the desired height. Adjustable peg - adjust fender height by simply pulling on the strap. Max.

Windex 10 Sport Wind Indicator from DAVIS INSTRUMENTS
Easy to remove for trailering In winds as light as 2/10th knots the sapphire suspension bearing allows the Windex to seek wind direction. No other wind vane in the world is as sensitive to extreme light air and small puffs, or as responsive when the breeze picks up. For small boats and dinghies. Includes a 10" vane, adjustable tacking tabs and glass reinforced polycarbonate J-Base for side, top or front of mast mounting. Stands only 9. 25" tall and weighs 1.

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

Tubing-Alu 7/8X20' from WEST MARINE
Bright 304 polished stainless steel or bright anodized aluminum. Used for a multitude of applications including grab rails, bow rails, and canvas top frames. Match materials between components to minimize corrosion. Stainless has . 049" wall thickness . Aluminum has . 058" wall thickness . Use 7/8" tubing for smaller powerboats . Use 1" tubing for sailboats and larger powerboats . Available in 6', 12' and 20' lengths .

G. O'Day 222/Santana 525,Length 47", Height at tip 2 1/4", Width at butt 1 1/2", Width at tip 2" from WEST MARINE
Replace that old ugly tiller with a new hand-made laminated ash and mahogany wood tiller, made to fit your rudder hardware, and pre-finished with multiple coats of premium marine spar varnish. Choose the right length and profile, and the butt-end measurements to fit your rudderhead hardware. Can’t find a good fit? Idasailor Marine can custom-build a tiller to your measurements . Custom tillers are shipped direct within 10 days . Click HERE to open the PDF custom order form.

Tiller Tamer from DAVIS INSTRUMENTS
Smooth, adjustable control of tiller movement, for short periods of "self-steering. " Particularly useful when changing sails, motoring, etc. on short-handed boats.