Teak Sealer/Dressing - Quart from TEAK WONDER
Restores and protects the splendid beauty of teakTwo-part system cleans away dirt and black discoloration and restores teak to a lustrous hue. Won't affect paint, varnish or metal surfaces. Follow up with Sealer/Dressing Step one loosens dirt and mildew. Step two neutralizes step one. Rinsing reveals the bright natural beauty of the wood.

Micron CSC Antifouling Paint, Red, Quart from INTERLUX
Haul and relaunch without loss of performance The innovative copper-copolymer formula of Micron CSC provides a controlled release of antifouling biocide at the paint surface, which means that the longevity of the coating is related to the amount of paint applied. Can be applied over most paints in good condition. Micron CSC will not lose its effectiveness when hauled out of the water for extended periods of time (such as winter storage). Type: Copolymer . 2% Cuprous Oxide . Additives: None .

Brightside Pre-Kote Primer - Gray, Quart from INTERLUX
Fills minor blemishes and sands easilyOne part primer for use with Brightside or any other one-part topside enamel. Microspheres provide high build and improved sandability. (Replaces Brightside Primer and 279 White Undercoater. ) Application: Brush, roller, airless/conventional spray . Number of Coats Recommended: One or two, depending on surface condition. Drying: Overcoating: 6 to 12 hrs. Drying Time: To touch: 1 to 3 hrs. Coverage: Brush: 112 sq. ft/qt, 450 sq. ft/gal; Spray: 87 sq.

Cetol Marine Light - Quart from INTERLUX
Enhances and protects the natural beauty of interior and exterior woodSemi-transparent finish prevents weathering and repels water. just wash wood thoroughly and apply. Three coats are recommended for the first application, followed by annual touchups. Marine Light is more translucent than Marine. If a gloss finish is desired, either may be overcoated with Marine Gloss. Quart. Long-lasting adhesion and protection from UV rays and weathering. Flexible, breathable, translucent finish; Quarts.

VC-Offshore - Baltoplate Gray, Gallon from INTERLUX
Used by performance boatsVC Offshore combines superior antifouling performance with a super smooth low friction surface for the performance conscious boater. This high-strength, vinyl antifouling paint, fortified with Teflon® yields a hard, very smooth finish for maximum durability, reduced friction and increased performance. High copper loading fights fouling on performance boats in saltwater. Can be used in fresh, salt and brackish waters. Should not be applied over non-vinyl bottom paints.

WetOrDry™ Finishing Sandpaper - Ultra Fine 600 Grit, 5 Pack from 3M PRODUCTS
Ideal for wet sanding between coats of varnish, paint and other finishes. Made with silicon carbide, a sharp synthetic mineral that cuts fast and is satin smooth.

G. O'Day 222/Santana 525,Length 47", Height at tip 2 1/4", Width at butt 1 1/2", Width at tip 2" from WEST MARINE
Replace that old ugly tiller with a new hand-made laminated ash and mahogany wood tiller, made to fit your rudder hardware, and pre-finished with multiple coats of premium marine spar varnish. Choose the right length and profile, and the butt-end measurements to fit your rudderhead hardware. Can’t find a good fit? Idasailor Marine can custom-build a tiller to your measurements . Custom tillers are shipped direct within 10 days . Click HERE to open the PDF custom order form.

Europa Pure Badger Brush - 3" from CORONA
For smooth paint and varnish applicationBadger-like bristles have tip “flags” for smooth paint and varnish finishes. For fine finishes. Flagged tips for sharper cutting edge.

Scotch General Painting Masking Tape #2050 - 2" from 3M PRODUCTS
Use in a wide range of painting applicationsGeneral-purpose. Not for critical or extended outdoor use. Recommended Usage: General purpose masking or binding tape; adheres to previously painted or varnished surfaces . Material: Crepe paper with rubber resin adhesive . Removal Time: Three days .

Power Tune Engine Cleaner, 13 oz. from MERCURY MARINE
Dissolve gum, varnish, deposits and clogs in the fuel system and combustion chambersScrub carburetors and injectors clean with this detergent cocktail of solvents and motor oil. Fast-acting chemical dissolves gum, varnish, deposits and clogs in the fuel system and combustion chambers. For 2- and 4-cycle engines. 13oz.

Sta-Bil Gas Stabilizer - 8oz. from STA-BIL
Guards against gum and varnish in fuelKeeps stored fuel fresh indefinitely so your engine will start easily even after being stored all winter. Prevents gum and varnish buildup and protects metal surfaces from corrosion. Use for storing up to 12 months. 8oz.

Stern Rail Outboard Motor Mount - Aluminum for 1-1/4" Railings from EDSON CORPORATION
Built to hold motors up to 15 hp or 100 lbs/45 kg. Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with non-skid pad, bolted to the UV stable poly backing board always looks ship-shape… no more varnishing. Bottom cleat comes unattached so that it will fit any rail spacing. Note: 1-1/4” rail version comes complete with anodized aluminum bracket, stainless cleat and stainless U-bolt for 1-1/4” railing.

LP Enamel - Hatteras White, Quart from STERLING
A popular choice among many boatyard professionals as well as do-it-yourself boat owners who want superb gloss and durability. Pros spray it, yet the Sterling Brushing System captures the same look, thanks to its unique flow properties. Sterling brushing system: Pick a color base, mix 2:1 with U-2964. Add a dash of U-2900 accelerator in cool weather. Thin about 25% with U-2965. Apply on nonskid surfaces with low-nap foam rollers and tip several times. Apply with premium China bristle brush.

Inflatable Boat Antifouling Paint from PETTIT
Water-based, multi-season ablative antifouling paint. For hard- or soft-bottom inflatables. Cleans up with water. Black. Quart. Type: Copolymer Ablative. Recommended Usage: PVC or Hypalon; trailered boats. Biocide: CuOx 41%. Additives: No. Compatibility: With all other antifouling paints in good condition except VC-17. Number of Coats Recommended: Two.

Cetol Marine Gloss Overcoat, Quart from SIKKENS
Bring out wood’s natural shine! Enhances and protects the natural beauty of interior and exterior wood. Semi-transparent finish prevents weathering and repels water. Easy to use—just wash wood thoroughly and apply. Three coats are recommended for the first application, followed by annual touchups. Apply by brush only—no sanding required. A fine orange-brown translucent finish is left—use alone or with Cetol overcoat. Coverage: 85 sq. Recommended Usage: Exterior and interior, above water .