Welcome! Please Sign-In
Top Sellers
Port Gasket - 5" x 12" from BECKSON MARINE INC
Port Gasket - 5" x 12" from BECKSON MARINE INC
Gaskets ensure a weatherproof seal.
Stainless-Steel “S” Hook, 3/16" Wire Dia., 5/8" Inside Width from SEAFIT
Stainless-Steel “S” Hook, 3/16" Wire Dia., 5/8" Inside Width from SEAFIT
Stainless Steel "S" Hooks. Polished Stainless Steel Made in the U. S. A.
Nylon Tee, NPT Threaded, 1/2" from SEAFIT
Nylon Tee, NPT Threaded, 1/2" from SEAFIT
Nylon Tees, NPT Threaded.
Footman’s Loop, Fits 2" Webbing from SEAFIT
Footman’s Loop, Fits 2" Webbing from SEAFIT
Low-profile stainless-steel straps for attaching webbing to flat surfaces.
Stainless-Steel 12V Receptacle from SEAFIT
Stainless-Steel 12V Receptacle from SEAFIT
Built to last for years in the marine environment.
Striping Tape - Dark Blue, 3/4" from SEAFIT
Striping Tape - Dark Blue, 3/4" from SEAFIT
Premium 2mil. thick vinyl striping tape makes it easy to add a colorful accent to your boat! Made from the same material used in quality custom boat graphics. It will not crack or peel, even in salt water, and the colors last from 5–7 years without fading. It can even be applied below the waterline. It can be bent, waved, and applied around corners. Should you change your mind or decide to update the look of your boat, simply remove the tape–no need to sand or ruin your paint or finish.
Medium Folding Grapnel Anchor from SEAFIT
Medium Folding Grapnel Anchor from SEAFIT
Like mushroom anchors, this four-fluke anchor is a safe choice for inflatables - there are no open flukes to puncture fabric. It's easy to store and won't get tangled in other lines on your boat.
Barbed Hose Reducer, 3/8" to 5/8" from SEAFIT
Barbed Hose Reducer, 3/8" to 5/8" from SEAFIT
Nylon Hose Reducers, Barbed.
Transom Drain Tube - 1 x 3" from SEAFIT DRAIN
Adjustable Packing Nut Wrench from SEAFIT
Adjustable Packing Nut Wrench from SEAFIT
Better than a pipe wrench If you are not equipped with wrenches that fit the nuts on your stuffing box, we suggest you purchase TWO of these. Why? Because you will need two to make an adjustment: One for the locking nut and one for the adjusting nut. These wrenches tend to be easier to use than pipe wrenches—especially in tight engine spaces where many boaters must work. Primary Usage: Adjust/remove inboard shaft packing nut . Size: 1" to 3" adjustable .
Bulb-Festoon Red-T10 x 31 - 12V 10W from SEAFIT
Bulb-Festoon Red-T10 x 31 - 12V 10W from SEAFIT
BULB-FESTOON RED-T10X31-12V10W.
Brass-Bristle Brush from SEAFIT
Brass-Bristle Brush from SEAFIT
Solid brass bristles won't rust or corrodeLarge, plastic utility brush has solid brass bristles that won’t rust or corrode. Brass bristles are slightly softer than stainless steel and are therefore less intrusive to surfaces. Molded plastic handle provides solid, controlled grip. Bristles: 5/8"D. Overall length: 8 1/2". Molded plastic handle provides solid, controlled grip. 5/8"L bristles.
Bootstripe Tape, 2'' Black from SEAFIT
Bootstripe Tape, 2'' Black from SEAFIT
Great for use along the waterline or as an accent along the gunnelsThese self-adhesive vinyl accent stripes liven up the look of any boat. Vibrant, long lasting colors add just the right touch of pizzazz to your boat's exterior, changing it from drab and ordinary to bright, clean and beautiful. Sold in 50' rolls.
Spc Stripe Tape, 2'' Blue from SEAFIT
Spc Stripe Tape, 2'' Blue from SEAFIT
The easy way to add excitement to your boatAdd these stripes for a vibrant dose of color. A top carrier holds the stripes in alignment during application, ensuring flawless results.
Bootstripe Tape, 1'' Blue from SEAFIT
Bootstripe Tape, 1'' Blue from SEAFIT
Great for use along the waterline or as an accent along the gunnelsThese self-adhesive vinyl accent stripes liven up the look of any boat. Vibrant, long lasting colors add just the right touch of pizzazz to your boat's exterior, changing it from drab and ordinary to bright, clean and beautiful. Sold in 50' rolls.

SEAFIT Port

5" x 12" Replacement Stainless-Steel Bug Screen from SEAFIT Home -> Cabinet & Deck Hardware -> Hatches & Ports->Replacement Stainless Steel Bug Screens for Bronze or Stainless Ports
Replacement bug screens for your polished bronze or stainless steel ports.
Part No: 133509
Bronze Port, 7" x 14" Door Opening ID, 7-3/8" x 14-3/8" Cutout Size from SEAFIT Home -> Cabinet & Deck Hardware -> Hatches & Ports -> Ports->Rectangular Ports
Laminated safety glass. Hinges contain adjusting screws for gasket compression. Flange and finish ring drilled for wood screws (not meant to be bolted together). Spigots are sloped for drainage. Includes fitted bug screen. Cutout radius: 1-1/4". Latches: Bronze dogs and studs (bronze ports) or bronze stud with black bakelite knob (stainless ports). Hinges: Non-locking, 180° . Material: Highly polished bronze or 304 stainless steel. Included Accessories: Fitted bug screen .
Part No: 132112
Bronze Port, 5" x 12" Door Opening ID, 5-3/8" x 12-3/8" Cutout Size from SEAFIT Home -> Cabinet & Deck Hardware -> Hatches & Ports -> Ports->Rectangular Ports
Laminated safety glass. Hinges contain adjusting screws for gasket compression. Flange and finish ring drilled for wood screws (not meant to be bolted together). Spigots are sloped for drainage. Includes fitted bug screen. Cutout radius: 1-1/4". Latches: Bronze dogs and studs (bronze ports) or bronze stud with black bakelite knob (stainless ports). Hinges: Non-locking, 180° . Material: Highly polished bronze or 304 stainless steel. Included Accessories: Fitted bug screen .
Part No: 132012
Replacement Stainless Steel Bug Screens for Bronze or Stainless Ports from SEAFIT Home -> Cabinet & Deck Hardware -> Hatches & Ports
Replacement bug screens for your polished bronze or stainless steel ports.
10" Hatch Arm from SEAFIT Home -> Cabinet & Deck Hardware -> Hatches & Ports
Small coil spring hatch support features a 10" length, stainless steel bracket construction and mounts with four stainless steel #10 fasteners. 3/8" chrome plated support spring provides 2. 25lb. restoring force to assist in lifting hatches when fully closed. May be used in pairs for additional support of long or heavy hatches.
Part No: HA-S
11" Hatch Arm from SEAFIT Home -> Cabinet & Deck Hardware -> Hatches & Ports -> Hatch Accessories
Small coil spring hatch support features a 10" length, stainless steel bracket construction and mounts with four stainless steel #10 fasteners. 3/8" chrome plated support spring provides 2. 25lb. restoring force to assist in lifting hatches when fully closed. May be used in pairs for additional support of long or heavy hatches.
Part No: HA-M
13-3/4" Hatch Arm from SEAFIT Home -> Cabinet & Deck Hardware -> Hatches & Ports
Small coil spring hatch support features a 10" length, stainless steel bracket construction and mounts with four stainless steel #10 fasteners. 3/8" chrome plated support spring provides 2. 25lb. restoring force to assist in lifting hatches when fully closed. May be used in pairs for additional support of long or heavy hatches.
Part No: 7652087
Portlight Chain - Brass from SEAFIT Home -> Cabinet & Deck Hardware -> Hatches & Ports
Highly polished brass toggle clasp with 8" chain.
Part No: 130010
Premium Hatch Adjuster from SEAFIT Home -> Cabinet & Deck Hardware -> Hatches & Ports
Heavy-duty stainless steel, combined with a positive-locking butterfly nut, provide a rust and corrosion-resistant hatch adjuster that delivers exceptional strength and holding power. Closed: 12"; extended: 21".
Part No: 7084SS
1-1/2" Bronze Check Valve from SEAFIT Home -> Plumbing -> Fittings & Valves->Bronze Check Valves
For vertical or horizontal use in fuel or water systems to maintain pump prime or prevent backflow to fluid source. The unique design minimizes fluid turbulence and flow restriction.
Part No: 290608
Brass Male Pipe-to-Hose, NPT, 1/4" Pipe, 5/16" Hose from SEAFIT Home -> Plumbing -> Fittings & Valves->Spin-On Installation Fittings
Each filter requires two brass pipe-to-hose barbs, one each for the inlet and outlet, sized to fit your fuel line.
Part No: 139734
Brass Male Pipe-to-Hose, NPT, 1/4" Pipe, 3/8" Hose from SEAFIT Home -> Plumbing -> Fittings & Valves->Spin-On Installation Fittings
Each filter requires two brass pipe-to-hose barbs, one each for the inlet and outlet, sized to fit your fuel line.
Part No: 139735
   Company History
   Mission Statement
   Press Room
   Careers at West Marine
   Affiliate Program
   Annual Catalog
   Store Locator
   And More...
   Stock Price
   Press Releases
   SEC Filings
   Email Alerts
   Analyst Coverage
   Management Team
   Financial FAQ
   And More...
   Terms Of Use
   Returns/Exchanges
   Privacy Policy
   Contact Us
   Site Map
   Annual Catalog
   Product Recalls
   And More...
Product offering and prices listed on this website (www.westmarine.com) are limited to Internet and phone orders (1-800-BOATING). Prices on periodic web-only specials apply only to Internet orders. Product offering and/or prices may vary at West Marine retail stores. ©2009 West Marine | All Rights Reservedpics11