Auxiliary Steering Kits for Trolling Motors - Zinc Rod from MARINETECH PRODUCTS
Steer your trolling motor with your boat's main steering wheel. These connector rods attach the trolling motor directly to the main engine—when the big one moves, the little one moves along with it. Kits come complete with two quick disconnect ball joint assemblies which make taking it off when you don't need it easy. Connect rod length is 24", cut it to size for a perfect fit. Use the drive bracket for motors that have SeaStar or Teleflex steering.

Rail Mount Outboard Bracket, 10 1/2" from WEST MARINE
Keep your small outboard safe and upright on the stern rail, rather than stowed in a locker where gasoline from the tank could cause hazardous fumes to collect, or spill and ruin stored goods. Two-piece mounting blocks clamp around a 1'' O. D. rail ''T''. Holds outboards up to 8 hp. Each comes complete with stainless mounting bolts. UV-stabilized polypropylene.

SeaStar Filler Kit from TELEFLEX
SeaStar hydraulic steering systems require the use of a special high-quality hydraulic fluid meeting MIL SPEC H-5606 C.

BayStar Helm Seal Kits from TELEFLEX
Replacement front seal kits for both front and rear mount helms. HS5147 fits BayStar front mount and SportTilt helms . Contains 3 screws, shaft seal and o-ring seal.

Aluminum Transom Support Master Mounting Kit from TELEFLEX
Universal mount for most outboard engine steering applications. This kit includes the Teleflex Outboard Clamp Block, Support Tube, and the Clevis Kit.

Big-T Rotary Helm from TELEFLEX
Die-cast gears and added shaft support help it hold up to tough use. For single or twin station powerboats up to 34'. Boat Type: Inboards and power-assisted sterndrives, up to 34' . Steering Type: Rotary . Dimensions: 6-13/16"D behind dash front x 6-3/8"W x 5-1/16"H . Steering Wheel: Up to 20". Not included . Steering Wheel Shaft: 3/4" tapered . Cable Type: QC II SSC61XX or SSC72XX . Mounting Hardware: Requires bezel kit sold separately .

Repl. Cylinder - Repl. Hynautic Model K2 from TELEFLEX
Hydraulic Cylinders -- the same quality steering components that comprise the many Hynautic systems may also be ordered independently for both new or retrofit applications.

3300 Pivot Kit, Brass from TELEFLEX
3300 Pivot Kit, Brass.

Outboard Lock - Merc/Mariner (40hp), 1/2" x 20 thread from MCGARD
Help make your outboard less attractive to thieves, and also keep it from vibrating loose while running. The vinyl-clad steel tube slides over the mounting screws and is secured with a hardened brass padlock. Padlock is recessed inside the tube to protect against cutting. Comes with two keys. *Fits: OMC 6-30hp, Merc/Mariner 8-25hp, Yamaha 9. 9-40hp, Suzuki 8-13hp.

SeaStar Helm Seal Kit from TELEFLEX
Replacement shaft seal kit HS5176 fits various post-1990 SeaStar 1. 4, 1. 7 (I), 2. 0, 2. 4 (II), SeaStar Pro and SeaStar helms.

Fuel Sending Unit Only - 4-24'' Tank from TELEFLEX
Complete kit includes a reliable dash-mount gauge with a black face and white numerals. The triple patented sending unit has an adjustable float arm and U-channel that fits virtually all tanks from 4"-24" deep. Compatible with 12V DC systems with common or insulated ground.

Stern Rail Outboard Motor Mount for 1" Railing from EDSON CORPORATION
Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with nonskid pad, bolted to the UV stable poly backing board always looks shipshape. no more varnishing. Comes complete with hardware to attach to any standard 1'' (2. 5cm) stainless rail. Warning: Be sure the engine is securely tied onto the backing board and the engine mounts are tightened whenever the engine is stored on Edson's Outboard Motor Mount.

Anode Kit - 818298Q 1 from MERCURY MARINE
Mercury/MerCruiser Anodes and Anode Kit - VPN - - Description - - Fits - A 31640Q 4 Trim Tab Anode Fits most Mercury/Mariner outboards 35 hp. & above and all MerCruiser except Bravo. & above and all MerCruiser except Bravo. C 806189Q 1 Trim Cylinder Anode Fits Alpha One Gen II drives. D 806190Q 1 Trim Cylinder Anode Fits Bravo I, II, III, X, XR, XZ and Blackhawk drives. F 826134Q Side Pocket Anode Fits Mercury/Mariner 30-300hp outboards, Force 90 & 120hp 1995 and newer outboards.

Auxiliary Outboard Bracket, 9-1/2" Vertical Lift, 7.5hp-30hp HP Rating from GARELICK
Built extra-tough and extra-wide for secondary engines including new higher-torque, four-stroke engines. Stainless torsion springs for easy lifting. Mounting board is 2" weatherproof and maintenance-free polypropylene. Five-position lock bar allows for better range trim adjustment. Maximum Weight: Model #193328: 169 lbs. , Model # 3683455: 175 lbs. . Style: Adjustable . Material: Anodized aluminum body w/ poly-propylene board . Attachment Method: Thru-bolt, backing plate .

Flo-Torq II Hub Kit, Mercury 225 EFI fourstroke outboards; Yamaha 225hp 4-stroke outboards, Prop Series B from MERCURY MARINE
Change props faster, cheaper, with Quicksilver's modular hubFlo TorQ II modular propellers let you easily switch props, change pitch, change from aluminum to stainless, or replace a bent propeller. They're a direct replacement for the Michigan XHS hub kits. When large underwater obstruction are encountered, the Delrin sleeve of the Flo-Torq II System is designed to "break away" following impact, ensuring that damage to the engine, engine drive and propeller is kept to a minimum.