7/16" G40 Chain, 7200lb. SWL, 21,600lb. Breaking Strength, 2.05lb./ft., 300' Standard Pack from ACCO CHAIN
Hot-Dipped galvanized Grade 40 HT Acco anchor chain! An industry standard, hot-galvanized, high-tensile anchor chain combines both high tensile strength and is resistance to wear. Meets ISO standards . Calibrated to ensure the proper fit for your windlass. 7200 lbs.

Type IV Standard Buoyant Cushion - White from KENT
Conventional throwable cushions meet USCG requirements for Type IV PFDs. Comfortable to sit on or to use as a backrest. Durable fabric covers. Heavy polypropylene straps make them easy to throw. Buoyancy: 18 lbs. Dimensions: 15"L x 16"W x 2. 5"H.

Stainless-Steel Horizon™ Claw Anchors 11lb. 15'-25' from LEWMAR
Made of precision-cast 316 stainless steel, these claw anchors are patterned after anchors developed to secure oil rigs in the North Sea. Extremely effective in a variety of sea beds, tides, and wind conditions. Reset fast if they become dislodged due to changing conditions. Stows conveniently on the bow roller of most boats.

5/16" BBB Chain, 1900lb. SWL, 7600lb. Breaking Strength, 1.2lb./ft., 550' Standard Pack from ACCO CHAIN
Bulk Chain We stock a complete selection of I. standard chain from Acco to fit almost any windlass. chain vendors. When comparing Acco chain to other brands, be sure to ask if other models are “hot-dip. ” Remember that the Safe Working Load (SWL) is a conservative rating for safety and should not be exceeded, although the breaking strength is generally 3–4 times greater. BBB is made of low-carbon steel, but has shorter, calibrated links that are designed to be compatible with many windlasses.

Flat Cam Riser, 1"H from HARKEN
Harken Cam-Matic cleats are legendary for smooth operation when holding and releasing control lines. Three rows of Delrin ball bearings allow the jaws to open and close smoothly under the highest loads. Light springs allow the cleats to open freely, so the teeth do not have to be sharp which means that your line lasts longer. Use models with aluminum jaws for high loads, or when the line will be drawn through the teeth for adjustment.

Primer Pump Assembly (220, 225, 245) from RACOR-PARKER FILTRAT
For Racor Spin-On Series Diesel Fuel Filter/Water Separators.

Vent Plug (120, 122, 220 & 225) from RACOR-PARKER FILTRAT
For Racor Spin-On Series Diesel Fuel Filter/Water Separators.

Seal Service Kit, (220, 225, 245) from RACOR-PARKER FILTRAT
For Racor Spin-On Series Diesel Fuel Filter/Water Separators.

Replacement Ball Bearings for 150 Cam Cleat from HARKEN
Harken Cam-Matic cleats are legendary for smooth operation when holding and releasing control lines. Three rows of Delrin ball bearings allow the jaws to open and close smoothly under the highest loads. Light springs allow the cleats to open freely, so the teeth do not have to be sharp which means that your line lasts longer. Use models with aluminum jaws for high loads, or when the line will be drawn through the teeth for adjustment.

2.5 Gallon, TCW-3 Quicksilver Oil from MERCURY MARINE
This two-cycle oil far exceeds TC-W3 standards to provide superior engine protection.

Flow-Max Ball Scupper from T-H MARINE
Positive sealing ball scupper with twist-off design makes clearing debris a snap. Simply twist to remove ball cavity. Includes stainless steel security pin, multiple mounting holes and a neutral buoyancy ball that won’t float up and break the seal. Meets all ABYC standards.

SW Inverter/Charger Remote Panel with 50ft. Cable from XANTREX
Designed for use with SW and PS inverter/chargers, the SWRC is a full-function remote control with backlit LCD display. The remote control comes with a standard 25’ (7. 5 m) cable or a 50’ optional (15 m) cable.

3/8" Bow/Stern Eye - 1.03" ID Between Studs x 4.63" Thread Length from SUNCOR
Bow / Stern Eye 304 Stainless Steel - Formed . Each U-Bolt set includes four nuts (two standard and two beveled) . Includes one bow plate, and one stern plate. . Threads are "UNC". . Stock size: 3/8" . ID between studs: 1. 03" . Thread length: 2. 50" .

C-10 Thermostat Controller from KASCO MARINE INC.
Kasco's NEW C-10 Thermostat Controller is designed to save you money on your electric bills The C-10 differs from our existing C-20 Controller, in that, it only uses Air Temperature to operate the De-Icer. Simply use the dial to set a temperature in which you want the De-Icer to turn on and plug the C-10 into a standard 120V outlet.

Potable Water Holding Tank, 3 Gal. from TODD ENTERPRISES
1520) requirements. Standard Tanks feature a multiple port arrangement that enables use as a sanitation holding tank or for potable water storage. They include two 1 1/2" fill/drain ports and two 1/2" vent/supply ports. Designed for waste storage, each includes two 1 1/2" ports for inlet and drain and one 1/2" vent port. Both Standard and Heavy-Duty Tanks feature threaded NPT ports that are molded in to eliminate stress cracks and leaks. One year warranty.