Top Sellers
Tubing-Alu 7/8X20' from WEST MARINE
Bright 304 polished stainless steel or bright anodized aluminum. Used for a multitude of applications including grab rails, bow rails, and canvas top frames. Match materials between components to minimize corrosion. Stainless has . 049" wall thickness . Aluminum has . 058" wall thickness . Use 7/8" tubing for smaller powerboats . Use 1" tubing for sailboats and larger powerboats . Available in 6', 12' and 20' lengths .
|
Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.
|
Transom Drain Tube & Plug from MOELLER
This nylon drain tube won't rot, bend or mildew, fits flush to your transom, and allows water to drain when your vessel is trailered. A rubber O-ring makes a watertight seal. Can be loosened with a flat-head screwdriver. Fits 1 1/8'' openings. Mounted with rivets or #8 fasteners.
|
Speedometer Kit 80mph, 20-80mph, Includes pitot, 20' tubing, Dia, 3.78", Mounting Hole Max/Min, 3.41"/3.44", D 2.7" from TELEFLEX
White dial, black numerals, black pointer with fire-orange tip. Scratch-resistant curved glass lenses with polished stainless steel, near flush bezels. U. S. and metric scales with ISO symbols .
|
Lube Tube Adapter for Yamaha, Nissan, Tohatsu, Honda (2-50hp) from WEST MARINE
Marine lower unit drain, flush and fill tool. Metal threaded fitting fits MerCruiser, OMC, Evinrude, Johnson, Honda (70-90hp), Volvo, Force and Gamefishier lower units. Quick, easy and clean way to change marine lower unit gear lube. For use with all 8- and 10-oz.
|
|
|
Sierra-Tube-Exhaust from SIERRA
Some larger V-8 engines that create a large amount of back pressure use exhaust tubes rather than bellows. This helps to relieve the excessive pressure and eliminate problems with premature bellows failure. In the past, the exhaust bellows would blow up like a balloon and cause the drive shaft bellows to rub against the yoke and U-joints causing holes in the bellows.
|
Repl. Cylinder - Repl. Hynautic Model K2 from TELEFLEX
Hydraulic Cylinders -- the same quality steering components that comprise the many Hynautic systems may also be ordered independently for both new or retrofit applications.
|
ADJ 7-15-DL Whisker Pole, 83"/9lb. Collapsed Length/Weight, 202" Max. Working Length, 2" Tubing Diameters from FORESPAR
These telescoping whisker poles are heavy-duty two-section and three-section aluminum spars which can be extended to lengths up to 17' and securely locked in position by an internal twist lock device. Poles feature self-latching Ultra Series™ fittings on the inboard and outboard ends. Aluminum tubing. End Fitting Inboard: UPX. End Fitting Outboard: UPX.
|
|
|
SeaStar Helm Seal Kit from TELEFLEX
Replacement shaft seal kit HS5176 fits various post-1990 SeaStar 1. 4, 1. 7 (I), 2. 0, 2. 4 (II), SeaStar Pro and SeaStar helms.
|
BayStar Helm Seal Kits from TELEFLEX
Replacement front seal kits for both front and rear mount helms. HS5147 fits BayStar front mount and SportTilt helms . Contains 3 screws, shaft seal and o-ring seal.
|
Tach Diesel Mag. P.U. 4000 rpm from TELEFLEX
A popular choice for gas and diesel inboard engines, White Premier instruments feature white dials with modern black and blue graphics and superior light pipe illumination. When illuminated, black dial grads and pointer become red. Fog-resistant design for enhanced readability.
|
|
|
33C Red Jacket Cable, 18' from TELEFLEX
The most widely used cable type in the world. 8" minimum bend radius. Cable adapter kits available for use with Mercury, MerCruiser, Johnson/ Evinrude, and OMC sterndrive. 3" travel.
|
|
TELEFLEX Tubing
|
|
Home -> Engine Systems -> Steering Systems -> Mechanical Steering->Support Tube
Smooth aluminum tube supports the end of the steering cable before it attaches to the engine. Non threaded for clamp-block applications. Aluminum or stainless.
Part No: SA27274P
|
|
|
|
Home -> Engine Systems -> Steering Systems->Support Tube
Smooth aluminum tube supports the end of the steering cable before it attaches to the engine. Non threaded for clamp-block applications. Aluminum or stainless.
Part No: SA27275P
|
|
|
|
Home -> Engine Systems -> Steering Systems -> Steering Kits
Hydraulic steering for outboards to 150hpControlling large outboards with mechanical steering may require lots of effort. On the other hand, traditional hydraulic systems may be more than is needed on lower horsepower engines. The balanced cylinder features a compact design that easily fits most splashwells 23" or less. The cylinder utilizes the factory outboard engine supplied drag link for simplified installation. Boat Type: Single station, single engine boat with outboard up to 150HP.
Part No: HK4200A
|
|
|
|
Home -> Engine Systems -> Steering Systems->Clamp Blocks
Used as a standoff from the transom (outboards without tilt tubes) or a stringer (inboard model) for the steering cable.
Part No: SA27579P
|
|
|
|
Home -> Engine Systems -> Steering Systems
This link arm is designed to return to the motor-steering attachment point for through-the-tilt-tube mounting applications, which are common in modern outboards.
Part No: SA27361P
|
|
|
|
Home -> Engine Systems -> Steering Systems->Clamp Blocks
Used as a standoff from the transom (outboards without tilt tubes) or a stringer (inboard model) for the steering cable.
Part No: SA27149P
|
|
|
|
Home -> Engine Systems -> Steering Systems->Clamp Blocks
Used as a standoff from the transom (outboards without tilt tubes) or a stringer (inboard model) for the steering cable.
Part No: SA27055P
|
|
|
|
Home -> Engine Systems -> Steering Systems
Flexible 3/8''OD, 5/16''ID nylon tubing for use on all SeaStar I and II helm installations. Maximum recommended length is 100' total.
Part No: HT5100
|
|
|
|
Home -> Engine Systems -> Steering Systems->Transom Support Master Mounting Kits
Universal mount for most outboard engine steering applications. This kit includes the Teleflex Outboard Clamp Block, Support Tube, and the Clevis Kit.
Part No: SA27256P
|
|
|
|
Home -> Engine Systems -> Engine Instruments -> Engine Instr. Components
White and blue graphics on a black dial background makes Premier a smart choice for all modern and traditional boats. With Premier fog-resistant range for peace of mind in any conditions. Set consists of tachometer, 65 MPH speedometer (with pitot tube), fuel gauge (compatible with common marine senders), and voltmeter. Also includes water temperature and oil pressure. Actual hole sizes: Nominal 2" = 2. 13"/2. 16" except Hourmeter = 2. 00/2. Nominal 3" = 3.
Part No: 62715P
|
|
|
|
Home -> Engine Systems -> Steering Systems->Splashwell Mounting Kits
Add this kit to make the splashwell the point at which the pushpull cable is mounted. Ball and socket motion aligns the steering cable automatically. Corrosion-resistant. Includes threaded tube, splashwell guard and mounting hardware.
Part No: SA36316P
|
|
|
|
Home -> Engine Systems -> Engine Instruments -> Engine Instr. Components
The slotted mounting plate means no drilling required for replacement installments.
Part No: 56973P
|
|
|