Johnson/Evinrude, motor only, for 2-wire systems, 90–225hp (1991–1999) from SIERRA
Tilt/Trim Motors, Outboard Applications.

Power Tilt & Trim Fluid - Quart from WEST MARINE
Formulated to provide viscosity and lubricity necessary for proper pump performance and seal life. Combats high operating pressures and resists rust.

Stern Rail Outboard Motor Mount for 1" Railing from EDSON CORPORATION
Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with nonskid pad, bolted to the UV stable poly backing board always looks shipshape. no more varnishing. Comes complete with hardware to attach to any standard 1'' (2. 5cm) stainless rail. Warning: Be sure the engine is securely tied onto the backing board and the engine mounts are tightened whenever the engine is stored on Edson's Outboard Motor Mount.

Transom Trim Control from T-H MARINE
Weatherproof tilt control switch can be installed anywhere on the boat, such as back by the motor for more convenience. Can adjust trim or jack plates.

Auxiliary Outboard Bracket, 9-1/2" Vertical Lift, 7.5hp-30hp HP Rating from GARELICK
Built extra-tough and extra-wide for secondary engines including new higher-torque, four-stroke engines. Stainless torsion springs for easy lifting. Mounting board is 2" weatherproof and maintenance-free polypropylene. Five-position lock bar allows for better range trim adjustment. Maximum Weight: Model #193328: 169 lbs. , Model # 3683455: 175 lbs. . Style: Adjustable . Material: Anodized aluminum body w/ poly-propylene board . Attachment Method: Thru-bolt, backing plate .

Series 315 Outboard Fuel Hose - 3/8"ID from SHIELDS RUBBER
Premium-quality fuel hose designed for outboard feed and vent lines. Remains flexible at low temperatures and resists UV sunlight. Silverado 2000 complies with SAE J1527 Type B2 specifications. Should not be used in applications requiring the use of Type B1 fuel feed line.

Outboard Lock - Merc/Mariner (40hp), 1/2" x 20 thread from MCGARD
Help make your outboard less attractive to thieves, and also keep it from vibrating loose while running. The vinyl-clad steel tube slides over the mounting screws and is secured with a hardened brass padlock. Padlock is recessed inside the tube to protect against cutting. Comes with two keys. *Fits: OMC 6-30hp, Merc/Mariner 8-25hp, Yamaha 9. 9-40hp, Suzuki 8-13hp.

Motor Mate Lifting Davit from FORESPAR
The unit stores in its own 31" (787. Comes with tackle and will lift anything from the dinghy to the cockpit (or vice-versa) up to 100 lbs. Great for the dinghy motor, but also good for scuba tanks, ice, duffel bags, groceries, etc. The Motor Mate uses a Railfast® mounted ring on the rail and a "toe" on the cockpit coaming directly under the rail. Lightweight, portable, compact . Ideal for lifting outboard motors, sea bags, scuba gear . Lifting capacity: 100 lbs.

Rail Mount Outboard Bracket, 10 1/2" from WEST MARINE
Keep your small outboard safe and upright on the stern rail, rather than stowed in a locker where gasoline from the tank could cause hazardous fumes to collect, or spill and ruin stored goods. Two-piece mounting blocks clamp around a 1'' O. D. rail ''T''. Holds outboards up to 8 hp. Each comes complete with stainless mounting bolts. UV-stabilized polypropylene.

Stern Rail Outboard Motor Mount - Aluminum for 1-1/4" Railings from EDSON CORPORATION
Built to hold motors up to 15 hp or 100 lbs/45 kg. Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with non-skid pad, bolted to the UV stable poly backing board always looks ship-shape… no more varnishing. Bottom cleat comes unattached so that it will fit any rail spacing. Note: 1-1/4” rail version comes complete with anodized aluminum bracket, stainless cleat and stainless U-bolt for 1-1/4” railing.

Flusher-OB/IO Dual Rect Cups from WEST MARINE
Regular flushing of salt, silt, etc. helps extend your outboard engine‘s life. Clamping the flusher over your engine’s water intake on the lower unit and fresh water from a garden hose is all you need.

Engine Spray Paint -Mercury Phantom Black (1960-Pres.) from MOELLER
Durable, heat- and solvent-resistant acrylic lacquers formulated for use on all outboard and inboard engines, stern drive and lower unit applications. They are color-matched to original OEM colors and are a great way to protect your engine and make it look like new. 12oz.

Engine Spray Paint - Johnson/Evinrude, Light Blue Metallic (1978-87) from MOELLER
Durable, heat- and solvent-resistant acrylic lacquers formulated for use on all outboard and inboard engines, stern drive and lower unit applications. They are color-matched to original OEM colors and are a great way to protect your engine and make it look like new. 12oz.

Engine Spray Paint - Yamaha Metallic Blue Silver (1985-90) from MOELLER
Durable, heat- and solvent-resistant acrylic lacquers formulated for use on all outboard and inboard engines, stern drive and lower unit applications. They are color-matched to original OEM colors and are a great way to protect your engine and make it look like new. 12oz.

Johnson/Evinrude Outboard Starter, 120 to 140hp V4 (1985-99), 10 tooth drive gear from SIERRA
Sierra's new and remanufactured starters are the only marine starters that meet Marine UL standards. Sierra's remanufactured starters all have new solenoids, drives, bushings, brushes and springs. The bodies are powder coated for greater corrosion resistance. Sierra has entered an agreement with United Technologies to market their complete line of outboard starters and components. All are 100% load tested . Our remanufactured starters are covered by Sierra's customer satisfaction warranty .