Johnson/Evinrude, motor only, for 2-wire systems, 90–225hp (1991–1999) from SIERRA
Tilt/Trim Motors, Outboard Applications.

Power Tilt & Trim Fluid - Quart from WEST MARINE
Formulated to provide viscosity and lubricity necessary for proper pump performance and seal life. Combats high operating pressures and resists rust.

Transom Trim Control from T-H MARINE
Weatherproof tilt control switch can be installed anywhere on the boat, such as back by the motor for more convenience. Can adjust trim or jack plates.

Replaces OMC P/N 378444 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

For Chrysler/Force, 89-817109A2 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.

Auxiliary Steering Kits for Trolling Motors - Zinc Rod from MARINETECH PRODUCTS
Steer your trolling motor with your boat's main steering wheel. These connector rods attach the trolling motor directly to the main engine—when the big one moves, the little one moves along with it. Kits come complete with two quick disconnect ball joint assemblies which make taking it off when you don't need it easy. Connect rod length is 24", cut it to size for a perfect fit. Use the drive bracket for motors that have SeaStar or Teleflex steering.

Stern Rail Outboard Motor Mount for 1" Railing from EDSON CORPORATION
Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with nonskid pad, bolted to the UV stable poly backing board always looks shipshape. no more varnishing. Comes complete with hardware to attach to any standard 1'' (2. 5cm) stainless rail. Warning: Be sure the engine is securely tied onto the backing board and the engine mounts are tightened whenever the engine is stored on Edson's Outboard Motor Mount.

Bilge Pro Replacement Motor Cartridge for 500gph Pumps from JOHNSON PUMP
In the event of a problem, replacing your cartridge bilge pump motor is easy— provided you keep one of these on hand. Just pop out the old cartridge and pop in the new. Fit Johnson, West Marine Bilge Pro and Mayfair cartridge-style bilge and livewell pumps.

Motor Mate Lifting Davit from FORESPAR
The unit stores in its own 31" (787. Comes with tackle and will lift anything from the dinghy to the cockpit (or vice-versa) up to 100 lbs. Great for the dinghy motor, but also good for scuba tanks, ice, duffel bags, groceries, etc. The Motor Mate uses a Railfast® mounted ring on the rail and a "toe" on the cockpit coaming directly under the rail. Lightweight, portable, compact . Ideal for lifting outboard motors, sea bags, scuba gear . Lifting capacity: 100 lbs.

AC3000 Auto Trim Tab Control from BENNETT MARINE
Automatic controls for your Bennett Trim Tab system Give your trim tab system real smarts! The Auto Tab Control dials in the perfect running attitude. Just turn it on and it does the rest. Constantly monitors your boat's position and uses your trim tabs to maintain a perfect cruising attitude. Saves fuel and creates the perfect ride .

Stern Rail Outboard Motor Mount - Aluminum for 1-1/4" Railings from EDSON CORPORATION
Built to hold motors up to 15 hp or 100 lbs/45 kg. Convenient cleat and side handles allow you to tie the motor and lock it safely on board. The non-corroding polished 316 stainless bracket with non-skid pad, bolted to the UV stable poly backing board always looks ship-shape… no more varnishing. Bottom cleat comes unattached so that it will fit any rail spacing. Note: 1-1/4” rail version comes complete with anodized aluminum bracket, stainless cleat and stainless U-bolt for 1-1/4” railing.

OSCO GASKET FOR 274147 from OSCO MOTORS CORP.
Fits Osco Motors # 8125 manifold .

Side-Mount with Trim & Tilt 4-Wire from TELEFLEX
SL-3 is specifically engineered for installation without control modifications. Port or starboard installation with various cable-entry angles. Adapts for push or pull mode without tools. “Easy-On” cable design means no shift or throttle adjustments. Optional trim switch in handle grip for one-hand operation. Functions: Gearshift/throttle . Levers: Dual functions—each lever controls throttle and shift . Lever Material: Metal . Features: Push button for neutral Adjustable brake .

Impeller, 18-3062 from SIERRA
Recommended replacement schedule is every 3 years for fresh water and every year for salt water Click to view a Sierra Impeller Application Chart (PDF) For further assistance, have your year & model information handy and call our Product Advisors at 1-800-BOATING.

Walker Bay 10, 9'8" Length, 4'9" Beam, 126lb., 449lb. Capacity (up to 3 people) from WALKER BAY BOATS
Bolt in the seats, break out the oars (or optional sail kit or motor) and you’re ready to cast off. Boats include exclusive Hydro-Curve Oars. Application: Rowing, motoring or sailing . Hull Material: High Impact Polypropylene . Construction: High-pressure injection molded . Hull Shape: Round bottom lapstrake-style . Standard Hardware: Oars, oar locks, seats, stainless bow eye, Wheel in the Keel™ . Available Accessories: Sail kits, RID kits, Bimini boat cover . Warranty: 10 years limited.