Tubing-Alu 7/8X20' from WEST MARINE
Bright 304 polished stainless steel or bright anodized aluminum. Used for a multitude of applications including grab rails, bow rails, and canvas top frames. Match materials between components to minimize corrosion. Stainless has . 049" wall thickness . Aluminum has . 058" wall thickness . Use 7/8" tubing for smaller powerboats . Use 1" tubing for sailboats and larger powerboats . Available in 6', 12' and 20' lengths .

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Transom Drain Tube & Plug from MOELLER
This nylon drain tube won't rot, bend or mildew, fits flush to your transom, and allows water to drain when your vessel is trailered. A rubber O-ring makes a watertight seal. Can be loosened with a flat-head screwdriver. Fits 1 1/8'' openings. Mounted with rivets or #8 fasteners.

Lube Tube Adapter for Yamaha, Nissan, Tohatsu, Honda (2-50hp) from WEST MARINE
Marine lower unit drain, flush and fill tool. Metal threaded fitting fits MerCruiser, OMC, Evinrude, Johnson, Honda (70-90hp), Volvo, Force and Gamefishier lower units. Quick, easy and clean way to change marine lower unit gear lube. For use with all 8- and 10-oz.

Sierra-Tube-Exhaust from SIERRA
Some larger V-8 engines that create a large amount of back pressure use exhaust tubes rather than bellows. This helps to relieve the excessive pressure and eliminate problems with premature bellows failure. In the past, the exhaust bellows would blow up like a balloon and cause the drive shaft bellows to rub against the yoke and U-joints causing holes in the bellows.

ADJ 7-15-DL Whisker Pole, 83"/9lb. Collapsed Length/Weight, 202" Max. Working Length, 2" Tubing Diameters from FORESPAR
These telescoping whisker poles are heavy-duty two-section and three-section aluminum spars which can be extended to lengths up to 17' and securely locked in position by an internal twist lock device. Poles feature self-latching Ultra Series™ fittings on the inboard and outboard ends. Aluminum tubing. End Fitting Inboard: UPX. End Fitting Outboard: UPX.

Stainless-Steel “S” Hook, 3/16" Wire Dia., 5/8" Inside Width from SEAFIT
Stainless Steel "S" Hooks. Polished Stainless Steel Made in the U. S. A.

Nylon Tee, NPT Threaded, 1/2" from SEAFIT
Nylon Tees, NPT Threaded.

Footman’s Loop, Fits 2" Webbing from SEAFIT
Low-profile stainless-steel straps for attaching webbing to flat surfaces.

Stainless-Steel 12V Receptacle from SEAFIT
Built to last for years in the marine environment.

Striping Tape - Dark Blue, 3/4" from SEAFIT
Premium 2mil. thick vinyl striping tape makes it easy to add a colorful accent to your boat! Made from the same material used in quality custom boat graphics. It will not crack or peel, even in salt water, and the colors last from 5–7 years without fading. It can even be applied below the waterline. It can be bent, waved, and applied around corners. Should you change your mind or decide to update the look of your boat, simply remove the tape–no need to sand or ruin your paint or finish.

Medium Folding Grapnel Anchor from SEAFIT
Like mushroom anchors, this four-fluke anchor is a safe choice for inflatables - there are no open flukes to puncture fabric. It's easy to store and won't get tangled in other lines on your boat.

Barbed Hose Reducer, 3/8" to 5/8" from SEAFIT
Nylon Hose Reducers, Barbed.

Adjustable Packing Nut Wrench from SEAFIT
Better than a pipe wrench If you are not equipped with wrenches that fit the nuts on your stuffing box, we suggest you purchase TWO of these. Why? Because you will need two to make an adjustment: One for the locking nut and one for the adjusting nut. These wrenches tend to be easier to use than pipe wrenches—especially in tight engine spaces where many boaters must work. Primary Usage: Adjust/remove inboard shaft packing nut . Size: 1" to 3" adjustable .

Bulb-Festoon Red-T10 x 31 - 12V 10W from SEAFIT
BULB-FESTOON RED-T10X31-12V10W.