Ring Style Car RC-125 from FORESPAR
Separates the up/down and side-to-side motions of the pole to make a bind-free, strong attachment. Shackles are supplied for uphaul/downhaul lines. Stainless steel cheeks, aluminum body and plastic liners. Ring Style Car RC-125 Although a screw-pin stop is supplied, this car is designed to be used with uphaul/downhaul blocks shackled to the bails at each end. Ring ID: 1 5/8". Investment cast stainless steel with plastic liners to reduce friction. Fits UXP and UTR pole end fittings.

Straight Adapter, 30A Male/15A Female (straight blade, not locking, connections) from MARINCO
Marinco straight adapters allow you to connect from one dockside receptacle (or other power source receptacle) to one boatside inlet or equipment of dissimilar power configuration. They are integral fittings with no wire between the end fittings. They are high-quality, but do not have sealing boots and are not recommended for use in wet applications.

Windshield Support Bar, 13" from TAYLOR
Top-quality support bars are original equipment on many walk-thru windshields. Anodized aluminum tubing with nylon fittings, which pivot in almost any direction for easy installation.

T-Top Boat Cover, Center-Line Length 20'5" to 21'4", Blue from TAYLOR
The main features of these covers are: Bow and stern sections are separated into two halves. The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of console tube incorporates an adjustable draw rope in both front and rear sections.

T-Top Boat Cover, Center-Line Length 19'5" to 20'4", Blue from TAYLOR
The main features of these covers are: Bow and stern sections are separated into two halves. The sections are joined through the use of a 7mm single pull molded nylon zipper on both the port and starboard sides. Cover design incorporates a "console tube" section with two adjustable straps which lift and secure the cover halves up and over the console body and up under the T-top. The top edge of console tube incorporates an adjustable draw rope in both front and rear sections.

Transom Drain Tube & Plug from MOELLER
This nylon drain tube won't rot, bend or mildew, fits flush to your transom, and allows water to drain when your vessel is trailered. A rubber O-ring makes a watertight seal. Can be loosened with a flat-head screwdriver. Fits 1 1/8'' openings. Mounted with rivets or #8 fasteners.

Tubing-Alu 7/8X20' from WEST MARINE
Bright 304 polished stainless steel or bright anodized aluminum. Used for a multitude of applications including grab rails, bow rails, and canvas top frames. Match materials between components to minimize corrosion. Stainless has . 049" wall thickness . Aluminum has . 058" wall thickness . Use 7/8" tubing for smaller powerboats . Use 1" tubing for sailboats and larger powerboats . Available in 6', 12' and 20' lengths .

Tubing SS 1''X20' from WEST MARINE
Bright 304 polished stainless steel or bright anodized aluminum. Used for a multitude of applications including grab rails, bow rails, and canvas top frames. Match materials between components to minimize corrosion. Stainless has . 049" wall thickness . Aluminum has . 058" wall thickness . Use 7/8" tubing for smaller powerboats . Use 1" tubing for sailboats and larger powerboats . Available in 6', 12' and 20' lengths .

Lube Tube Adapter for Yamaha, Nissan, Tohatsu, Honda (2-50hp) from WEST MARINE
Marine lower unit drain, flush and fill tool. Metal threaded fitting fits MerCruiser, OMC, Evinrude, Johnson, Honda (70-90hp), Volvo, Force and Gamefishier lower units. Quick, easy and clean way to change marine lower unit gear lube. For use with all 8- and 10-oz.

Spinnaker Pole Car, Track #2720, 900sq.ft. Max. Sail Area, 1125lb. SWL from HARKEN
Now with captive ball bearings, which eliminates the need for a ball-bearing loader during installation or removal from track. These cars run freely, fit low-beam traveler track and are easy to adjust under any load.

Sail Tie, Ball End 16IN, Blue from STARBRITE
Securing your mainsail to the boom is simpler and quicker when you use sail lashes instead of conventional ties. Dual lengths of durable, UV-resistant polyester plastic cord have polyethylene ball ends with brass stops and damping rings. Color-coded balls.

T-Ball Swage Fitting, 1/8" Wire Size from ALEXANDER-ROBERTS
Electropolished 316 stainless steel. Running Back style has a stainless bail rather than a swage end, to accept Dyneema or other rope for a running backstay. *Running Back style has a stainless bail rather than a swage end to accept Spectra or other rope for a running backstay. Style: Swage . Material: Electropolished Type 316 stainless steel . Configuration: T-ball swage .

Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.

Tee Type Sanitation Hose Fitting, Slip Fitting Thread from SHIELDS RUBBER
Fiberglass-reinforced nylon fittings designed to fit Shields Series 101, 148 and 144 hoses without heating or special tools. Use in sanitation systems, deck drain systems and water tank fill.

Bottom Support Pole Caps, Non-skid from DR. SHRINK
Bottom Support Pole Caps Dr. Shrink carries a full line of premium installation supplies to ensure a professional shrinkwrap job from start to finish.