WindMate™ 200 Wind Meter with Wind Direction from SPEEDTECH INSTRUMENT
Get accurate weather data, anytime, anywhere! Weather-on-the-spot in handheld units with convenient pocketknife design. WindMate 200 includes digital compass for wind direction, cross/head/tail wind readings and wind speed, temp and wind chill. Use it as a bearing compass! Base Type: Threaded for tripod mount . Battery Type: CR2032 Lithium battery (included) . Display Type: LCD . Dimensions: 3. 28"H x 1. 2"W x . 38" . Waterproof: Water-resistant to 4' and floats .

Water Spot Remover, 32 Oz. from DUCKY PRODUCTS
Specfically developed to remove hard water spots.

Standard Capacity Boji Water Softener, 5" x 24" from GENOVA PRODUCTS
Softens your water supply, yielding water that tastes fresher, is less corrosive to onboard plumbing and leaves fewer unsightly stains and water spots. Consists of a PVC cylinder containing a special Ion Exchange Resin that attracts hard substances in water (iron, calcium, etc. Complete kit includes the Boji Softener, a prefilter housing with activated carbon filter, 36" hose to connect Boji to prefilter, 3/4" hose fittings to plumb into water supply and molded integral feet.

Gen-Sep Water Separator, 2" Diameter, Gas In/Out 2.0", Water Outlet 1.5" from CENTEK INDUSTRIES
Position the water drain from the Gen-Sep just below the water line to eliminate water splash, especially important for nighttime operation. Gen-Sep will remove nearly all of the cooling water from the exhaust. That water can then be drained to a hull fitting just below the waterline, thus eliminating excess noise often created by splashing and pulsating water flow at the exhaust outlet. A slight downward angle is required for both the exhaust outlet and the exhaust gas tube. Dimensions: 10.

Antifreeze, -100 Engine & Water System - Gallon from SEAFIT
West Marine Pure Oceans -100° (-73°C) Marine Antifreeze provides the ultimate in extreme cold weather and corrosion protection for drinking water systems and all engines. Its premium additive package prevents corrosion of aluminum, copper, brass and solder, but will not harm rubber, seals or hose materials. Provides burst protection to -100°F (-73°C) and freeze protection within a range of -58°F to -63°F (-50°C to - 52°C).

TankWatch® 4 Water/Holding Tank Monitor from SEALAND
Reliable micro float switches activate empty, low, mid and full tank levels on the indicator panel. No electrical components contact water or waste. Easy to install using universal flange (sold separately). Includes cap with micro float switches . Indicator panel . Gasket and stainless mounting hardware . Adapts to fit any water or holding tank up to 22" . 45" adjustable probes available by Special Order .

10 Micron Diesel Fuel Filter/Water Separator with Metal Bowl from RACOR-PARKER FILTRAT
Racor’s Aquabloc filter media removes virtually 100% of water and solid contaminants. Filters have die-cast aluminum heads and come in different sizes for diesel engines and any rate of fuel flow. To be used on the suction side of the pump. See-thru bowls allow visual inspection for water; metal bowls are recommended for use in areas of high heat and are required by the US Coast Guard on inboard engines and gensets. Inlets/Outlets: 1/4" NPT female . Bowl Material: See-thru polymer .

Fuel Filter/Water Separator, 15/35gph Max. Flow, 6"H x 3.2"W x 3.2"D, Metal Bowl from RACOR-PARKER FILTRAT
Racor's famous Aquabloc® filter media separates water into the bottom of the drain bowl and ensures virtually 100% removal of water and solid contaminants. Filters come in different sizes for gasoline engines and any rate of fuel flow. Designed for use on the suction side of pump. All filters feature a die-cast aluminum head which is anodized and painted. Standard pipe-to-hose barbs are used for installation. Inlets/Outlets: 1/4" NPT, except 3/8" NPT on 660 series .

Water Circulating Pump - #18-3581 - Chrysler Inbd # 3004886, 3619542, 3619859, 3745985 from SIERRA
Water Pumps The water pump is the heart of your inboard or I/O cooling system. All Sierra pumps are bidirectional and can be installed on reverse rotation engines. The pumps are also powder coated for additional protection. Includes mounting gasket. Pumps include brass bi-directional impellers, brass plugs and fittings, carbon resin seal, all mounting gaskets, stainless steel seal cup and spring, stainless steel back plate (where required), and powder coating for maximum corrosion protection.

Light for Windex 10, 15 & Sport Wind Indicators from DAVIS INSTRUMENTS
This masthead light illuminates Windex® wind indicators for perfect night sailing Illuminates reflective reference tabs on underside of the Windex 10 and 15. Mounts directly to the masthead fitting. Draws only 120mA . Mast wire not included . Made of non-corrosive materials . Replacement bulb for Model 4481503.

Windex 15 Wind Indicator from DAVIS INSTRUMENTS
Improved with bird-proof spike Super-sensitive to slight changes in wind direction at the masthead, Windex Wind Indicators are popular around the world because they offer such an exceptional value. They feature sapphire jewel suspension bearings, large fin/low inertia vanes and easy-to-read, fully adjustable tacking-tab system for quick reference. The choice for most sailors, the Windex 15 features a 15" vane and reflectors for high visibility day and night.

SW Inverter/Charger Remote Panel with 50ft. Cable from XANTREX
Designed for use with SW and PS inverter/chargers, the SWRC is a full-function remote control with backlit LCD display. The remote control comes with a standard 25’ (7. 5 m) cable or a 50’ optional (15 m) cable.

Arrow Style Windvane from RONSTAN
Small boat wind indicators feature quality construction at a fraction of the price of other windvanes, so they are a great choice for junior sailors who might be rough on the equipment. Ronstan's new vanes are balanced for accuracy and molded in UV-stabilized nylon. The aluminum shaft can be removed from the mast bracket for trailering or security. Both the Pennant and Arrow style indicators include adjustable tacking angle arrows.

Series 250 Exhaust Hose, 2-3/8"ID, 2-3/4"OD, 230psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .

Series 250 Exhaust Hose, 7/8"ID, 1-3/16"OD, 565psi Burst Pressure from SHIELDS RUBBER
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .