Diesel Tank - Flexible 24GA, 27"L x 34"W from IMTRA CORPORATION
Tought 840-denier nylon is coated with a chemical and odor resistant neoprene/bitrile coating. This allows them to be used as waste holding tanks, too. Sine the tanks collapse as the fuel consumed, there is far less air in the tank to cause condensationa nd contamination. When all the fuel has been drawn off, simply roll up the tank and stow.

Diesel Tank - Flexible 37GA, 27"L x 46"W from IMTRA CORPORATION
Tought 840-denier nylon is coated with a chemical and odor resistant neoprene/bitrile coating. This allows them to be used as waste holding tanks, too. Sine the tanks collapse as the fuel consumed, there is far less air in the tank to cause condensationa nd contamination. When all the fuel has been drawn off, simply roll up the tank and stow.

Racor Bowl Wrench from RACOR-PARKER FILTRAT
Plastic hand wrench to remove all Racor metal or plastic spin-on bowls.

Adjustable Packing Nut Wrench from SEAFIT
Better than a pipe wrench If you are not equipped with wrenches that fit the nuts on your stuffing box, we suggest you purchase TWO of these. Why? Because you will need two to make an adjustment: One for the locking nut and one for the adjusting nut. These wrenches tend to be easier to use than pipe wrenches—especially in tight engine spaces where many boaters must work. Primary Usage: Adjust/remove inboard shaft packing nut . Size: 1" to 3" adjustable .

Prop Wrench 1-1/16in Yellow from WEST MARINE
For on the water repairs!This 1-1/16in yellow six point socket style prop wrench is a must-have item for on-the water repairs.

Stainless Steel Pliers & Wrench Set from WEST MARINE
Made of corrosion-resistant stainless steel, tools are drop forged, heat treated and have precision-milled jaws. Set includes 6" long nose pliers, 8" adjustable wrench and 10" groove joint pliers. Comfortable cushion grips.

Pedestal Steering Brake from EDSON CORPORATION
Especially handy on long runs or when operating under power, this brake can secure the wheel under most conditions and will hold the boat on course while the helmsman trims a sheet or goes below. The brake can always be overridden by the helmsman. Constructed of bronze with long-lasting linings, includes a stainless shaft and brake knob. For safety, the handle is designed to pop off if a line is tangled around it. Pre-drilled holes allow installation in about 20 minutes.

Waterproof Rooftop Cargo Bag from KEEPER CORPORATION
Increase your vehicle cargo space instantly! Get extra space in your vehicle on your next road trip. This waterproof, sun and wind resistant cargo bag straps onto your vehicle with built-in nylon straps. Folds down for easy storage. 15 cu. ft. capacity. 44" x 34" x 17".

Leather Wheel Kit, 29" to 40" Wheel from EDSON CORPORATION
Steer more comfortably with a wheel that’s never too hot or too cold. Suede leather fits 7/8"dia. tubing. Each kit fits a range of wheel sizes<\m>simply cut the length to fit your wheel.

Sportsman's Powerknob from EDSON CORPORATION
Twin races full of super-smooth ball-bearings makes quick turns effortless while backing down on a fish, docking or maneuvering in tight quarters. Easy installation gets you out on the water quickly with the ultimate in steering control.

Teak Steering Cockpit Table - Drop Leaf, Pedestal-Mount, 9 1/2" from EDSON CORPORATION
Formed wire brackets hold the table in the up position Solid teak tables to turn your cockpit into an entertainment center Clips secure the table to your pedestal guard in the down position Drop Leaf Tables Dimensions-- Open: 27” x 26”, Closed: 27” x 13” Luncheon Tables Dimensions: 13 1/2” x 24”.

Control Handle - Throttle 963SB-55 from EDSON CORPORATION
Highly polished, investment cast stainless steel, marked "Fast-Slow" and "Fwd-Rev". Designed to fit Edson Dual Lever Engine Controls.

Control Handle - Clutch 863PT-55 from EDSON CORPORATION
Highly polished, investment cast stainless steel, marked "Fast-Slow" and "Fwd-Rev". Designed to fit Edson Dual Lever Engine Controls.

Pedestal Guard from EDSON CORPORATION
Stainless-steel guard protects your wheel and pedestal while providing a secure handhold. Includes new stainless guard feet, stainless gasketed top plate and mounting hardware. 1-1/8" dia.

Stainless-Steel GPS Mounting Arm from EDSON CORPORATION
Pre-drilled to fit the Garmin 45 mounting bracket; also accepts most other round GPS brackets up to 3" (76mm) Arm designed to attach to all 1" & 1-1/4" pedestal guard tubes without removing tubes or existing wiring .