Top Sellers
Wet/Dry Sandpaper (AO) - P500A-Grit from 3M PRODUCTS
3M Imperial Wetordry Sanding Sheet, 9" x 11" Used in wet sanding, fine featheredging or last final sanding step before priming. Most flexible backing with more consistent scratch pattern make this 3Ms best wet sanding product. 500G.
|
High Gloss Gelcoat Compound Gallon from 3M PRODUCTS
Leaves a high gloss finish without wheel or swirl marksRemove fine scratches from production gel coat. Unique formulation reduces slinging while buffing and leaves a high gloss finish without wheel or swirl marks. Contains no wax or silicone.
|
101 Polysulfide Marine Sealant - White, 10 OZ from 3M PRODUCTS
Adhesive/sealant for a wide variety of materialsOne-part polysulfide product seals joints between similar and dissimilar surfaces wood, fiberglass, metal and glass above and below the waterline. Non-sagging, non-shrinking and permanently flexible. Excellent resistance to weathering. White. Recommended Usage: Seals mechanically fastened joints, above or below water; fiberglass, wood, metal, most plastics. Cure Time: Tack free: 5 hrs; complete cure in 14-21 days; remains permanently flexible.
|
Chafe Tape from 3M PRODUCTS
Adhesive-backed cloth chafe tape is made to wrap thimbles, docklines, and other points subject to wear.
|
WetOrDry™ Finishing Sandpaper - Ultra Fine 600 Grit, 5 Pack from 3M PRODUCTS
Ideal for wet sanding between coats of varnish, paint and other finishes. Made with silicon carbide, a sharp synthetic mineral that cuts fast and is satin smooth.
|
Marine Mildew Block from 3M PRODUCTS
Helps keep your boat fresh and looking like newUnique non-toxic formula provides long-lasting protection to help keep your boat fresh and looking like new. Works on virtually all surfaces above the waterline, including sails, seat cushions, carpeting, canvas, deck furniture, rub rails, showers, boat covers and vinyl. 16. 9oz. 16. 9oz.
|
Scotchgard Marine Liquid Wax, 1Liter from 3M PRODUCTS
Durable wax actually bonds to your boat's surfaceSpecial formulation uses reactive chemistry to actually bond to your boat’s surface and provide exceptionally high gloss with lasting durability. Protects gelcoat and topside coatings from damaging ultraviolet radiation, and is excellent for use on gelcoat, topside paints, painted aluminum and marine metal parts. Uses reactive chemistry to bond to your boat's surface. Exceptionally high gloss with lasting durability.
|
Fast Cure 5200 Sealant - White, 3 OZ from 3M PRODUCTS
Cures tack-free in just two hours The same performance as standard 5200, but becomes tack-free in just two hours and cures in 24 hours. White. Formulation: One-part polyurethane adhesive/sealant . Recommended Usage: Permanent bonding, above or below water. Extremely strong & flexible . Material Incompatibilities: Acrylics, Some plastics (ABS, Lexan) . Cure Time: Tack-free: 2 hrs. ; Complete cure: 24 hrs. . Cleanup: Mineral spirits or kerosene .
|
Scotch General Painting Masking Tape #2050 - 2" from 3M PRODUCTS
Use in a wide range of painting applicationsGeneral-purpose. Not for critical or extended outdoor use. Recommended Usage: General purpose masking or binding tape; adheres to previously painted or varnished surfaces . Material: Crepe paper with rubber resin adhesive . Removal Time: Three days .
|
Mildew-Resisant Silicone Caulk - Clear, 10 OZ from 3M PRODUCTS
Formulation: One-part silicone sealant Recommended Usage: Lexan®, Plexiglass™, gelcoat, fiberglass, glass, wood, metal, rubber, and vinyl Material Incompatibilities: None, compatible with acrylics; not as strong as polyurethane Cure Time: Tack free: 1 hr; complete cure: 24 hrs Cleanup: Soap and water Removal: Mechanical removal. Material Incompatibilities: None, compatible with acrylics; not as strong as polyurethane. Cure Time: Tack free: 1 hr; complete cure: 24 hrs. Cleanup: Soap and water.
|
Doodlebug Scrubbing Pad - Fine (White) from 3M PRODUCTS
Ideal for cleaning and scrubbing practically everything aboard. For cleaning and scrubbing virtually anything onboard .
|
Plastic Restorer from 3M PRODUCTS
Restore clarity and shine to exterior plastic, including polycarbonate, Lexan and acrylic hatches and windows. Use Plastic Restorer to remove hazing and stains. Follow up with Plastic Polish to remove minor imperfections and create a high-gloss shine. 8oz.
|
Mildew-Resisant Silicone Caulk - White, 3 OZ from 3M PRODUCTS
Formulation: One-part silicone sealant Recommended Usage: Lexan®, Plexiglass™, gelcoat, fiberglass, glass, wood, metal, rubber, and vinyl Material Incompatibilities: None, compatible with acrylics; not as strong as polyurethane Cure Time: Tack free: 1 hr; complete cure: 24 hrs Cleanup: Soap and water Removal: Mechanical removal. Material Incompatibilities: None, compatible with acrylics; not as strong as polyurethane. Cure Time: Tack free: 1 hr; complete cure: 24 hrs. Cleanup: Soap and water.
|
Non-Skid Deck Cleaner from 3M PRODUCTS
Cleans non-skid surfacesDesigned to clean hard-to-reach ground-in dirt and stains on non-skid surfaces. Safe for use on fiberglass, metal and painted surfaces. One Liter (34oz. ) One liter (34oz.
|
|
|
|
from SEADOG, from SEAFIT HARDWARE, from 3M PRODUCTS, 25'' from PERKO
|
|
Home -> Paint & Maintenance -> Caulking & Adhesives->5200 Polyurethane Adhesive/Sealant
Tenacious bonds and watertight seals above or below waterline Provides exceptionally strong adhesion, yet stays flexible after it cures; may be used above or below the waterline. Ideal for underwater thru-hull fittings, hull-to-deck joints, portholes and bonding wood to fiberglass. Goes on smoothly, won’t sag, and remains workable up to four hours. Cures in 5–7 days with no shrinking. Recommended Usage: Permanent bonding, above and below water. Removal: Mechanical removal .
Part No: 05203
|
|
|
|
Home -> Safety -> Flares & Signaling Devices->Sports Horn
Great for emergency signaling in fog or rescue situations! Ideal for coaches, sports officials, camp counselors, lifeguards and referees, while also meeting the needs of sports enthusiasts. 100% ozone safe, flammable isobutane propellant. Rugged, high impact plastic trumpet-guaranteed unbreakable. Removable trumpet for easy transport and storage. Refills readily available. Made in USA. Maximum Decibels: 130 dB . Size: 11" tall. Refill Size: 5. 5oz. .
Part No: FSH
|
|
|
|
Home -> Paint & Maintenance -> Caulking & Adhesives
Easy-to-apply, nontoxic debonding agent aids in hardware removal Debonds and aids in the removal of most polyurethane sealants. 1. 2 oz. spray. Nontoxic formula is easy to apply . Softens and debonds polyurethane caulks from gelcoat.
Part No: JWB-200-04
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->Universal Enamels Spray Paint
For application on diverse surfaces including fiberglass, wood, plastic, metal—even vinyl! These enamels are rust, fade, chip and chemical resistant and remain flexibile in extreme conditions. Ergonomic bottle with trigger actuation eliminates drips and finger fatigue. New misting system minimizes overspray and permits spraying from any angle—even upside down! Colors (except Flat Black) dry to a gloss finish. 12oz.
Part No: 245214
|
|
|
|
Home -> Engine Systems -> Engine Lubrication->Power Tilt & Trim Fluid
Formulated to provide viscosity and lubricity necessary for proper pump performance and seal life. Combats high operating pressures and resists rust.
Part No: 3704657
|
|
|
|
Home -> Paint & Maintenance -> Epoxy & Fiberglass -> Additives & Fiberglass->#423 Graphite Powder
423 Graphite Powder is a fine black powder that can be mixed with WEST SYSTEM epoxy to produce a low-friction exterior coating with increased scuff resistance and durability. Epoxy/graphite is commonly used as a bearing surface, and as a coating on rudders and centerboards, or on the bottoms of racing craft that are dry sailed. The epoxy/graphite mixture can also be used in teak deck construction to simulate the look of traditional seams and to protect the epoxy from sunlight. 7 oz.
Part No: 423-6
|
|
|
|
Home -> Plumbing -> Marine Sanitation -> Head Chemicals & Tissue->Head & Holding Tank Neutralizer & Flush
Use this preparation to neutralize, flush, and prepare your head and holding tank for use with new treatments. Eliminates cross contamination which can render a holding tank treatment useless when switching from one type to another. Also ideal for spring commissioning or as preparation for winter layup.
Part No: 9377094
|
|
|
|
Home -> Anchor & Docking -> Ladders, Ramps & Boat Hooks->Stainless Spring Clamps
Requires four #6 RHMS fasteners Sold in pairs .
Part No: 0502DP1STS
|
|
|
|
Home -> Anchor & Docking -> Ladders, Ramps & Boat Hooks
Use it to easily loop your dock lines around posts or pilings. Especially useful at low tide when the piling is too high to reach. Mounts to any boat pole.
Part No: 134
|
|
|
|
Home -> Paint & Maintenance -> Tools
Better than regular scissors for tough shearing tasks Quality mini-shears cut through almost anything—even a penny! Great for odd jobs at home or on the boat. Made of rust-resistant stainless steel.
Part No: 31608
|
|
|
|
Home -> Paint & Maintenance -> Zinc Anodes -> Shaft/Prop Nut Anodes
Attaches to standard Bennett trim tabs where actuator bolts to plate.
Part No: CMBNT1AZ
|
|
|
|
Home -> Anchor & Docking -> Fenders & Docking
Inflatable Vinyl Scare Eye Balloon with Mylar Tape Tail Visual Scare Device. Confuses Birds with Lifelike Reflective Predator Eyes and Markings. Ideal for use on Fruit Trees, Patio Covers, Pool Areas, Gazebos, Boats, Etc.
Part No: MMSEB
|
|
|
|
Home -> Engine Systems -> Engine Lubrication->Lower Unit Quart Pump
Metal threaded fitting fits MerCruiser, OMC, Evinrude, Johnson, Honda (70-90hp), Volvo, Force and Gamefisher lower units Fits standard quart plastic bottles. Flexible hose gets to hard-to-reach fill plugs.
Part No: 3704673
|
|
|
|
Home -> Sailboat -> Shackles, Snaps & Fittings -> Eyestraps, Fairleads, Bails->Footman’s Loops
Low-profile stainless-steel straps for attaching webbing to flat surfaces.
Part No: C0224-0050-W
|
|
|
|
Home -> Engine Systems -> Engine Parts
Fits Mercury/Mariner 4 and 5hp 2-stroke outboards and 4, 5 and 6hp 4-stroke outboards.
Part No: 16841Q02
|
|
|
|
Home -> Paint & Maintenance -> Cleaners, Soaps & Polishes
Maintains the clarity of new plastic and acrylicKeeps new, clear, plastic and acrylic surfaces clean and protected. Leaves a static-free coating. Safe and effective on both acrylic and polycarbonate surfaces. 8oz.
Part No: M-1008
|
|
|
|
Home -> Paint & Maintenance -> Cleaners, Soaps & Polishes
Cleans and protects your vinyl and rubberSpray on to remove ground-in dirt from soiled vinyl, rubber and plastic. Screens out damaging UV rays that can dry out and crack the surface. 16oz. 16oz.
Part No: M-5716-16OZ
|
|
|
|
Home -> Cabinet & Deck Hardware -> Cabinet Hardware & Locks
Highly polished brass . Fixed eye (does not swivel). 1"w x 1-7/8"L. Padlock hole diameter 5/16" .
Part No: 350710
|
|
|
|
Home -> Sailboat -> Traveler, Tracks & Vang -> Main Reefing & Furling->Downhaul Hooks
Stainless steel hook with closed perpendicular eye.
Part No: C0179-H008-W
|
|
|
|
Home -> Sailboat -> Shackles, Snaps & Fittings->Eye Bolts
Machined from 304 stainless steel.
Part No: 080488
|
|
|
|
Home -> Plumbing -> Fittings & Valves
Loop Cap Replacement for marelon vented loops.
Part No: 903002
|
|
|
|
Home -> Paint & Maintenance -> Epoxy & Fiberglass->West System Application Videos & Technical Books
WEST SYSTEM® Technical Books—Guide you through a wide range of projects and repairs These books are chock-full of important of information on recommended product usage, applications, and step-by-step instructions for a wide variety of projects, including blister repair, deck reinforcement, lamination repair, closing of punctures and holes, dry rot repairs and more. Specific step-by-step instructions. Helpful illustrations.
Part No: 002-550
|
|
|
|
Home -> Plumbing -> Hose & Hose Clamps -> Bulk Hose->Series 250 ShieldsFlex II Marine Water/Exhaust Hose with Wire
For use in all marine water and wet-exhaust applications. Also for marine wet-exhaust where connection requires great length (greater than 4 x ID) or significant bend. Meets or exceeds standards for certified wet-exhaust hose. Sold by the foot with a maximum continuous length of 10' except where preceded by an asterisk, which indicates a maximum continuous length of 50'. Construction: Black synthetic rubber with wire helix and HD synthetic cord . Temperature Range: –20° to 200° F .
Part No: 116-250-0783
|
|
|
|
Home -> Cordage -> Rigging Products -> Wind Instruments->Replacement Parts for Windex Wind Indicators
Use these replacement parts for all Windex Wind Indicators.
Part No: R3152
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes
Product Features: For use with Drop-In Hidden Horn - Marinco #11095 (and #11079).
Part No: 11090
|
|
|
|
Home -> Paint & Maintenance -> Epoxy & Fiberglass->Wood Putty
A quick and easy way to fill nicks and scratches in woodReal wood in a plastic base. Perfect for filling nicks and scratches in virtually any wood. Dries fast, sands easily and can be painted over. Dries fast.
Part No: 36041122
|
|
|
|
Home -> Engine Systems -> Engine Lubrication->Quicksilver High Performance Gear Lube
For use with all MerCruiser sterndrives and for added protection in outboards.
Part No: 802851Q02
|
|
|
|
Home -> Engine Systems -> Horns/Wipers/Glove Boxes->Flip Lock Drain Plugs
Standard rubber and brass plug fits 1" transom drains on many production boats.
Part No: Z10811
|
|
|
|
Home -> Paint & Maintenance -> Epoxy & Fiberglass -> Additives & Fiberglass->Resin Coloring Agent
Match colors like a pro with these coloring agentsFor use with polyester or epoxy resins, fillers, or putties. These tints also work well with nonskid coatings. Use with West Marine Gel Coat or Evercoat Polyester Gel Paste.
Part No: 100506
|
|
|
|
Home -> Paint & Maintenance -> Tools->5"-6" Bonnet Set
For final buff out, use the wool polishing bonnet included in this Seven Piece Bonnet Set which includes four applicators, two terry cloth, one wool and one microfiber polishing bonnet.
Part No: 39606
|
|
|
