Top Sellers
2-5/8" x 1-1/2" Euro Utility Hinge from WEST MARINE
Stamped utility hinge with 1/2" offset from TACO. Made of marine grade 304 stainless steel with polished finish, non-corrosive utility hinge is ideal for hatches, cabinets, and doors inside and outside the boat. Measures 2-5/8" x 1-1/2" x .
|
Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.
|
Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.
|
Series 150 Clear PVC Tubing, 1/2"ID, 45psi Burst Pressure from SHIELDS RUBBER
Single layer, nontoxic, FDA-approved clear vinyl tubing. Ideal for drain lines, iceboxes, refrigerators, livewells, bilge pump discharge, freshwater lines, water and holding tank vents. Sold per foot: 50’ maximum continuous length for 1/4" and 3/8" hose; 100' maximum continuous length for 1/2" hose and larger. Application: Non-pressurized water system supply; sink, shower, and icebox drains. Material: FDA formula vinyl. Reinforcement: None. Temperature Range: N/A.
|
Drain Plug, Bronze 1/2" NPT Threaded from MJS MANUFACTURING
Don’t forget to install your trailerable boat’s drain plug and get that sinking feeling! Get the Plug Boss instead. Put the bright red anodized aluminum plug holder in the most logical place possible, on the trailer winch handle, and never forget to reinstall your drain plug when you launch your boat (or remove it when you haul out). Choose a Plug Boss to fit either the 1" rubber tee handle drain plug or a 1/2" pipe threaded bronze drain plug.
|
|
|
1-7/8" Polished Brass Flush Ring Pull from ABI
Highly polished brass . Convenient flush-fitting ring pull for cabinets, small doors, and hatches. . 1-7/8"L x 1-1/2"w . Requires four #5 fasteners .
|
Non-Locking Flush Lock - Chrome/White with Offset Cam Bar from PERKO
Non-Locking chome plated zinc alloy and white plastic with offset adjustable cam bar. Detents indicate open or closed position. Door thickness: 1/4" to 1-1/8" . Face plate dimensions: 2-1/2" x 2-1/2" . Adjustment latch bar: 3/8" to 3" .
|
Hose Adapter, From 1-1/8" to 3/4"-5/8" from RULE INDUSTRIES
#69 is stepped & adapts from 1-1/8" to 3/4" - 5/8" #57 is an elbow & adapts from 1-1/8" to 1" NPT #67 adapts from 1-1/2" to 1-1/8".
|
Gas Deck Fill Replacement Cap, Plain from PERKO
Includes grounding lug with screw and integral retainer for cap For 1 1/2" hose Impervious to gasoline.
|
Acetal Thru-Transom Scupper from WEST MARINE
One-way rubber flapper valve and thru-hull fitting. For 1-1/2"ID hose. Overall length: 6-1/4". Installation hole size: 2". Max.
|
Flipper Pump from WHALE PUMPS
Easy back-and-forth action produces one-way discharge. Spout swivels. Made of nylon, aluminum and synthetic rubber. For 1/2"ID hose. Material: Nylon, aluminum, rubber . Capacity: 2gpm . Dimensions: 7-1/8"H x 6"dia. . Cutout Size: 2". Clearance: 4-1/2" .
|
Vertical Hand Pump Faucet, Chrome Over Brass from FYNSPRAY
Fynspray Vertical Hand Pump Faucet Vertical plunger pump with a gracefully arched spout. 50 strokes per gallon. Chrome over brass. 1"diameter tube . Fits 1/2"–5/8" hose .
|
Solid Brass Vertical Action Galley Pump from FYNSPRAY
Vertical plunger pump with a gracefully arched spout. 50 strokes per gallon. 1"diameter tube. Fits 1/2"–5/8" hose. Requires 8 1/2" clearance below counter surface; 9 3/4" above Material: Brass. Capacity: 50 strokes/gal. Dimensions: 9 3/4"H. Cutout Size: 1 1/8". Clearance: 8 1/2".
|
4.5" Stainless-Steel Pop-Up “Neat Cleat” from ATTWOOD
Retractable stainless steel cleats retract to only 1/2" above deck and have direct drainage to the bilge. Corrosion-free. Install easily. Hardware included. Functions: Drains to bilge with drainage receptacle. Requires 3/8" ID tube (not supplied) . Material: Stainless steel . Height: Lowered, 1/2"; Raised, 1-5/8" . Line Size: 1-1/4" line opening . Cutout Size: 7/8" hole saw size. Max.
|
|
1, 1-1, 2" from SEAFIT, 8" from SEAFIT, Locking from PERKO, 2
|
|
Home -> Cabinet & Deck Hardware -> Cabinet Hardware & Locks -> Catches & Latches
Chrome plated zinc alloy with sliding lock button. For door thickness 3/4 to 1-1/8 inches. Supplied with black plastic spacer for surface mounting. Bevel/Strike Type: Regular w/Box. Case Dimensions: 2-1/8 x 1-3/4 .
Part No: 1279DP0CHR
|
|
|
|
Home -> Paint & Maintenance -> Scrub Brushes & Hoses->Boating Accessories
Convert your Shurhold pole to a paddle or boathookUse thse accessories with Shurhold's "one-pole-does-it-all system. Boat Hook has line-carrying feature, centered push-off and basic boat hook. Paddle features Shur-Lok quick-release adapter and is a great safety item for any boat.
Part No: 130
|
|
|
|
Home -> Anchor & Docking -> Bulk Nylon & Poly Line->Ultra Blue Three-Strand Line
Ultra-strong line outlasts polypro two to one Made from bi-polymer olefin fiber, ultra-strong Ultra Blue is 30%–35% stronger than polypropylene and has more than twice the wear life. UV light resistance is excellent, it is easy to grip and it floats.
Part No: 130016806020
|
|
|
|
Home -> Anchor & Docking -> Ladders, Ramps & Boat Hooks
Contoured to hug the hull of inflatable boats. Attaches to floorboard or side with 3/8'' line and heavy-duty swivel snap. 1'' dia. anodized aluminum tubing with plastic rungs. Vinyl sleeves protect hull fabric.
Part No: 13002:01
|
|
|
|
Home -> Engine Systems -> Engine Parts
SELOC has been the leading source of how-to information for the marine industry since 1974. Designed and written to serve the needs of the professional mechanic, do-it-yourself boat enthusiast, instructor and student, these manuals are based on actual teardowns done by Seloc’s editors/authors in our on-site facility. 25-60 h. , 1 and 2 cylinders from 1971-1989. Every manual features: Easy-to-follow, step-by-step, illustrated procedures . Hundreds of exploded drawings, photographs and tables .
Part No: 1302
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Gas Fill & Tank Vent
Perko Gas Fill and Tank Vent This ingenious plastic deck fill has a vent with a flame arrestor built right into the fill flange. A flip-up cap eliminates the need for a deck key and no ground wire is required.
Part No: 1319DPGBLK
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Gas Deck Fills
Includes grounding lug with screw and integral retainer for cap For 1 1/2" hose Impervious to gasoline.
Part No: 1324DP0BLK
|
|
|
|
Home -> Anchor & Docking -> Ladders, Ramps & Boat Hooks
Use it to easily loop your dock lines around posts or pilings. Especially useful at low tide when the piling is too high to reach. Mounts to any boat pole.
Part No: 134
|
|
|
|
Home -> Plumbing -> Freshwater Systems
Complete with spray nozzle, polished-chrome deck holder and 6' heavy-duty white hose. ON/OFF trigger allows for intermittent water flow or continuous spray.
Part No: 135-0011-WH
|
|
|
|
Home -> Plumbing -> Freshwater Systems
This shower mixer has a water conservation button built-in to the handle. Chrome-plated with an easy grip handle, ceramic disc valves and 72" retractable hose. Includes flexible 1/2" NPT connection hoses for easy installation. Material: Brass . Dimensions: 6"H x 6-3/8"W x 7-1/4"L . Port Sizes: 1/2" NPT . Clearance: 2-1/4" . Cutout Size: 2-1/2". Manufacturer's Documents Installation Guidelines.
Part No: 135-0204-CW
|
|
|
|
Home -> Cabinet & Deck Hardware -> Hatches & Ports
Black plastic base, attached hose flange. 3" duct. Type: Cowl . Material: Chrome-plated zamak, plastic . Dimensions: 2-1/4"H x 5-5/16"W x 6"L . Cutout Size: 3" .
Part No: 1364A3
|
|
|
|
Home -> Plumbing -> Freshwater Systems
Ideal for mounting to any horizontal surface. Kit includes spray nozzle, hose and necessary hardware for easy installation. White. Material: ABS plastic . Dimensions: 3-7/8"H x 3"W x 2-7/8"L . Port Sizes: 1/2" NPT . Clearance: 2-1/4" .
Part No: 137-0000-WH
|
|
|
|
Home -> Engine Systems -> Engine Instruments->Chesapeake Series Instruments
Over 50 years of experience are behind every one of these Faria instrument gauges. They’re designed with an eye for sophistication and a mind for value. Perimeter lighted white dial with stylish blue and black graphics. Polished stainless steel bezel. Contoured black pointer and domed glass lens. All gauges are 12V DC with negative ground and are all internally illuminated unless otherwise noted. Include backclamp, hardware, and installation instructions. Mfr. ’s lifetime limited warranty.
Part No: 13808
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Brass Male Pipe-to-Hose, NPT
Brass Pipe Fittings.
Part No: 139733
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Nylon Female Pipe-to-Hose Adapters
Nylon Fittings, Female Pipe-to-Hose.
Part No: 139920
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Nylon Hose Elbows, Barbed
Nylon Hose Elbows, Barbed.
Part No: 139941
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Nylon Hose Reducers, Barbed
Nylon Hose Reducers, Barbed.
Part No: 139951
|
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Nylon Hose Reducers, Barbed
Nylon Hose Reducers, Barbed.
Part No: 139953
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Nylon Tees, NPT Threaded
Nylon Tees, NPT Threaded.
Part No: 139985
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Maxxflow Drains, Barbed
Flush head fits most standard showers and allows complete drainage, decreasing the likelihood of clogging.
Part No: 14060
|
|
|
|
|
Home -> Plumbing -> Fittings & Valves->Maxxflow Drains, Barbed
Flush head fits most standard showers and allows complete drainage, decreasing the likelihood of clogging.
Part No: 14142
|
|
|
|
Home -> Engine Systems -> Engine Parts
SELOC has been the leading source of how-to information for the marine industry since 1974. Designed and written to serve the needs of the professional mechanic, do-it-yourself boat enthusiast, instructor and student, these manuals are based on actual teardowns done by Seloc’s editors/authors in our on-site facility. This manual covers Mercury/Mariner Outboards, all 2-stroke engines, 2. 5-275HP from 1990-2000. Hundreds of exploded drawings, photographs and tables . Troubleshooting sections .
Part No: 1416
|
|
|
|
Home -> Engine Systems -> Engine Parts
SELOC Marine tune-up and repair manuals provide the most comprehensive, authoritative information available for outboard, inboard and stern-drive engines, as well as personal watercraft. SELOC has been the leading source of how-to information for the marine industry since 1974. This manual covers Mercury Outboard, all 2-stroke models, 2. 5-250HP from 2001-2005. Every manual features: Easy-to-follow, step-by-step, illustrated procedures . Hundreds of exploded drawings, photographs and tables .
Part No: 1418
|
|
|
|
Home -> Safety -> Life Jackets->Comfort Series™ Automatic Inflatable Life Vests
Comfortable enough for all day wear This automatic inflatable vest has an open design that lies away from your neck for a less restrictive fit and it's lighter weight to promote maximum movement—allowing you to comfortably wear it all day onboard. 5lb. Inflator Type: Halkey-Roberts V8500 6F . USCG Type: Type V with Type III performance: This vest must be worn to be counted in vessel's inventory of PFDs . Range Of Adjustment: 30"–52" adjustable chest straps .
Part No: 1431C/Y-00-WMP
|
|
|
|
Home -> Safety -> Life Jackets->Commercial Inflatable Life Vest
USCG-Approved Type V for use when worn on uninspected commercial vessels less than 40 ft. Approved substitute for a Type II or III PFD only when worn and used in accordance with the owner's manual. High-visibility reflective tape and emergency whistle on bladder . Halkey-Roberts 1F automatic inflator with single point indicator . Automatic inflation when submerged in water; manual inflation by pulling lanyard or by oral tube . Provides 33. Pocket to store extra cylinder or gear and D-ring .
Part No: 1470BLK-00-000
|
|
|
|
|
Home -> Safety -> Life Jackets->Commercial Inflatable Life Vest
USCG-Approved Type V for use when worn on uninspected commercial vessels less than 40 ft. Approved substitute for a Type II or III PFD only when worn and used in accordance with the owner's manual. High-visibility reflective tape and emergency whistle on bladder . Halkey-Roberts 1F automatic inflator with single point indicator . Automatic inflation when submerged in water; manual inflation by pulling lanyard or by oral tube . Provides 33. Pocket to store extra cylinder or gear and D-ring .
Part No: 1470ORG-00-000
|
|
|
|
Home -> Safety -> Life Jackets -> Recreational Life Jackets->Offshore Power Auto/Manual Inflatable Life Vest
The versatile inflator can be armed for automatic or manual inflation. Its fleece-lined collar keeps the vest from chafing the back of your neck. A clear window on the outside of the cover allows for fast inspection: green means it’s ready for use, red means it requires rearming. Comes equipped with a quick-release Delrin buckle, 2"W nylon webbing, front zip pocket, SOLAS-grade reflective tape, back-up oral inflation tube and arming cylinder with pill. Buoyancy: 33. 7lb. .
Part No: 1493YEL-00-WMP
|
|
|
|
Home -> Paint & Maintenance -> Paint, Varnish & Teak Oil->SeaFin Teak Oil
High-quality penetrating oil dries to a low sheen. Seals and protects interior and exterior wood from moisture and weather.
Part No: 15040
|
|
|
|
Home -> Sailboat -> Cleats & Stoppers -> Cam and Clam Cleats->Standard Cam Cleats and Accessories
Harken Cam-Matic cleats are legendary for smooth operation when holding and releasing control lines. Three rows of Delrin ball bearings allow the jaws to open and close smoothly under the highest loads. Light springs allow the cleats to open freely, so the teeth do not have to be sharp which means that your line lasts longer. Use models with aluminum jaws for high loads, or when the line will be drawn through the teeth for adjustment.
Part No: 150BALLS
|
|
|
|
Home -> Sailboat -> Running Rigging By The Foot->Endura 12™ Dyneema Single Braid
Extremely high strength-to-weight ratio! Excellent strength-to-weight ratio, ultra-low elongation, excellent flexibility and wet/dry strength retention, torque-free, and it floats. Constructed from Dyneema SK-75, Endura 12 has a proprietary urethane coating for improved abrasion resistance. Best Use: Halyards, sheets, low-stretch control lines, guys, slings/hoisting ropes . Construction: 12-strand single braid . Core Fiber/Construction: Coated Dyneema SK-75 . 0% at 30% of breaking strength .
Part No: 1520-04-00600
|
|
|
