Top Sellers
CARB GASKET KIT from SIERRA
Sierra carb kits and gaskets for engine tune ups.
|
Yamaha Carb Kit from SIERRA
Sierra carb kits and gaskets for engine tune ups.
|
Replaces OMC P/N 378444 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.
|
For Chrysler/Force, 89-817109A2 from SIERRA
Many of Sierra's solenoids are manufactured by our Independence, KS plant. We produce both starter solenoids and continuous duty solenoids for trim and tilt pumps. Our features add up to solenoids which offer maximum magnetic plunger pull, reduced voltage drop and maximum corrosion protection.
|
Water Circulating Pump - #18-3599 - Volvo #3851982-3, 3853850; Mercruiser #811841, 850399, 850399-1 from SIERRA
Water Pumps The water pump is the heart of your inboard or I/O cooling system. All Sierra pumps are bidirectional and can be installed on reverse rotation engines. The pumps are also powder coated for additional protection. Includes mounting gasket. Pumps include brass bi-directional impellers, brass plugs and fittings, carbon resin seal, all mounting gaskets, stainless steel seal cup and spring, stainless steel back plate (where required), and powder coating for maximum corrosion protection.
|
Johnson/Evinrude Outboard Starter, 120 to 140hp V4 (1985-99), 10 tooth drive gear from SIERRA
Sierra's new and remanufactured starters are the only marine starters that meet Marine UL standards. Sierra's remanufactured starters all have new solenoids, drives, bushings, brushes and springs. The bodies are powder coated for greater corrosion resistance. Sierra has entered an agreement with United Technologies to market their complete line of outboard starters and components. All are 100% load tested . Our remanufactured starters are covered by Sierra's customer satisfaction warranty .
|
30GPH Cartridge, Replaces Racor S3240 from SIERRA
High-performance fuel injected engines require ultimate fuel filtration, separation of water from the fuel supply and maximum fuel flow. Sierra’s filter elements deliver all three of these critical performance factors. 7900-Series 10 micron filters eliminate harmful contaminants at over 90% efficiency, while removing over 98. They’re engineered for today’s sterndrives and inboards, along with 2-cycle and 4-cycle outboards. That is why a high efficiency water separating filter is so important.
|
|
|
|
|
Prop Nut Kit, Yamaha 40-50HP from SIERRA
An excellent emergency item to carry in your toolbox, for those occasions when the prop nut is misplaced or lost.
|
Prop Nut Kit, Yamaha V4/V6 from SIERRA
An excellent emergency item to carry in your toolbox, for those occasions when the prop nut is misplaced or lost.
|
Exhaust Flapper Valve - 4" from SIERRA
Heavy duty rubber flapper valve keeps following seas from entering exhaust outlet when moving slowly or stopping.
|
|
|
20 Amp Pushbutton Thermal Circuit Breaker from SIERRA
Very common pushbutton breakers for DC loads. Uses two-blade terminals. Mounts in 3/8" hole. Can be used with a waterproof boot over the button. Buttons are white. Switch Type: Pushbutton . Voltage Compatibility: DC . Safety Features: Waterproof boots available . Housing Material: Plastic . Housing Dimensions: 1. 75" x 1.
|
3/8 inch inline fuel filter from SIERRA
For use on McCulloch/Scott-Atwater, Suzuki Outboard and Yamaha Outboard 18-7831 is replacement for Johnson/Evinrude Outboard #398319.
|
|
from HARKEN, 18654A1 from SIERRA, Key from SIERRA, Mercruiser from SIERRA
|
|
Home -> Anchor & Docking -> Ladders, Ramps & Boat Hooks -> Ladders & Ramps
For use on pontoon boat side gates. Special vinyl sleeves between the first and second step protect the pontoon from damage. The overrail hooks snap into amounting sockets (included) suitable for temporary or permanent mounting. Made of durable 1''dia. aluminum tubing with comfortable white molded plastic steps. Hooks fold flat for compact storage. Four steps. 50''L. Hooks:13.
Part No: 15240:01
|
|
|
|
Home -> Engine Systems -> Motor Mounts
The unit stores in its own 31" (787. Comes with tackle and will lift anything from the dinghy to the cockpit (or vice-versa) up to 100 lbs. Great for the dinghy motor, but also good for scuba tanks, ice, duffel bags, groceries, etc. The Motor Mate uses a Railfast® mounted ring on the rail and a "toe" on the cockpit coaming directly under the rail. Lightweight, portable, compact . Ideal for lifting outboard motors, sea bags, scuba gear . Lifting capacity: 100 lbs.
Part No: 153100
|
|
|
|
Home -> Engine Systems -> Motor Mounts
Longer reaching arms use strong, lightweight Marelon components The Nova Davit system represents the "State of the Art" for styling and function. Like all Nova products, a very high-standard finish will make the right statement about your boat. The neat folding feature stows the davit system flush with your boat's stern. The maximum safe working load is 300 lbs. Nova Davit conveniently folds inward to maintain boat slip length or remove them completely for stowage or racing.
Part No: 153302
|
|
|
|
Home -> Engine Systems -> Motor Mounts->Nova Lift™
Forespar's Nova Lift products combine elegant styling with superb strength and function. Other brands swing left and right without control. Nova Lift comes with a stainless-steel lower mounting tube that will accommodate 30" height rails. Vessels with rails higher than 30" will require the use of a deck pad (not included) to raise the installation to the proper height. The Nova Lift with Winch is ideal for trawlers and motor yachts where sailboat winches are not available. 220 lbs.
Part No: 153311
|
|
|
|
Home -> Sailboat -> Blocks -> Blocks->Midrange Hexaratchet® Blocks
Stronger versions of the Hexaratchet II+2 with 8:1 holding power. Beefier posts and wraparound straps handle higher working loads. Sheave: Teflon-impregnated Hardkote anodized aluminum. Bearings: Delrin. Sheave Size: 3" (76mm). Line Diameter: 9/16" max. Cheek Material/Finish: Plastic with wrap-around stainless straps. Shackle/Strap Type: Heavy-duty forged swivel with three-way head; locks or rotates. Cleat: 1556 and 1566: 280 Cam-Matic.
Part No: 1549
|
|
|
|
Home -> Sailboat -> Shackles, Snaps & Fittings -> Eyestraps, Fairleads, Bails
Forged eyestraps are extremely strong and their smooth shape won’t chafe line. Stainless steel . 6000lb. Breaking load.
Part No: 1558
|
|
|
|
Home -> Anchor & Docking -> Ladders, Ramps & Boat Hooks -> Ladders & Ramps->Anodized Aluminum Flip-Up Dock Ladder
Unique flip-up hinge mechanismUnique hinged ladder flips up and out of the water to prevent marine growth. Features a 10° angle for effortless boarding. Quick-release pins make it easy to remove for storage. 16"W steps have anodized aluminum tread and a curved step to make boarding more comfortable. Overall ladder width is 18". One-year warranty. Wide track 18"W ladder with full width 16" steps. Anodized aluminum heavy-walled 1"dia. tube construction.
Part No: 15730:01
|
|
|
|
Home -> Cabinet & Deck Hardware -> Cabinet Hardware & Locks->Nautilus Combination Lock
Set your own easy-to-remember combination on these padlocks with four-pin tumblers. You set the combination using the key provided. All brass internal components and a stainless steel shackle for superior corrosion protection. Type: Combination . Combination Type: Reset-able four tumbler . Material: Brass body and internal components, solid stainless shackle .
Part No: 15812
|
|
|
|
Investment Cast 316 Stainless Body / AISI 304 Stainless U-Bolt. Accepts 5/16" wire. 1-5/8" Long. 1-3/8" wide.
Part No: 159508
|
|
|
|
Home -> Engine Systems -> Engine Parts->Marine Rubber Exhaust Elbows
Exhaust hose elbows let your wet-exhaust line make tight turns without kinking. They provide excellent tolerance to engine heat, vibration and back pressure. Install over rigid tubing or pipe using the four included stainless T-bolt clamps (two at each end). Not intended for hose-to-hose connections. Lubricate with water or detergent. 250°F max.
Part No: 16-290-2000KIT
|
|
|
|
Home -> Paint & Maintenance -> Paint Brushes, Rollers & Tape->Europa Pure Badger Brushes
For smooth paint and varnish applicationBadger-like bristles have tip “flags” for smooth paint and varnish finishes. For fine finishes. Flagged tips for sharper cutting edge.
Part No: 160383
|
|
|
|
Home -> Engine Systems -> Engine Parts
Installs on outlet line and shows when to change filters by indicating an increase in suction. Complete kit includes gauge as well as male and female fittings for installation.
Part No: 1606B
|
|
|
|
Home -> Engine Systems -> Engine Parts
Water Impeller Repair Kit for 4hp to 8hp.
Part No: 16159A03
|
|
|
|
Home -> Cabinet & Deck Hardware -> Windshields->Windshield Support Bars
Top-quality support bars are original equipment on many walk-thru windshields. Anodized aluminum tubing with nylon fittings, which pivot in almost any direction for easy installation.
Part No: 1636
|
|
|
|
Home -> Sailboat -> Running Rigging By The Foot->Salsa Dyneema Single Braid
Single braid that’s easy to grip and low in stretch Salsa line is easy to grip, and has proven to be a great kink-free sheet for larger dinghies and keelboats. A high-tech version of Regatta Braid, but constructed with Dyneema SK-75 plus spun and filament polyester for reduced stretch. Your hands will love this soft and exceptionally strong single braid. Best Use: Sheets for larger dinghies and keelboats . Core Fiber/Construction: Dyneema SK-75/spun and filament polyester . Stretch: 2.
Part No: 1681-09-00600
|
|
|
|
Home -> Engine Systems -> Fuel Tanks
One combined product eliminates the need to install both a fuel line vent and a surge protector. Inertia of surging fuel drives the surge ball against upper seat, closing the large vent opening and limiting passage to smaller openings, which reduces fuel flow and minimizes spillage. Operates in any orientation within 45° of vertical. Baffles resist water intrusion during normal sea conditions and washdown. Constructed of glass filled polypropylene to withstand oil, gas, alcohol blended fuels.
Part No: 1684-6
|
|
|
|
Home -> Engine Systems -> Engine Parts
Fits Mercury/Mariner 4 and 5hp 2-stroke outboards and 4, 5 and 6hp 4-stroke outboards.
Part No: 16841Q02
|
|
|
|
Home -> Plumbing -> General Purpose Pumps -> General Purp Pump Parts->Impeller Kits
Each kit includes Engine Specified Impeller, - all necessary O-rings and Gaskets for up to 50 different model Sherwood Pumps, Technical Guide, with Trilingual Identification in a new robust clam shell case.
Part No: 17000K
|
|
|
|
Home -> Paint & Maintenance -> Caulking & Adhesives
Versitile adhesive/sealant for a variety of repairsAdhesive/sealant bonds to a wide variety of materials, including metal, canvas, wood, vinyl, and rope. UV resistant. Formulation: One-part adhesive Recommended Usage: Repairs vinyl seats, canopies, covers; seals windshields & ports; repairs diving masks & hoses Cure Time: Complete cure: 24 to 72 hrs. Quantity: 3. Recommended Usage: Repairs vinyl seats, canopies, covers; seals windshields & ports; repairs diving masks & hoses.
Part No: 170016
|
|
|
|
Home -> Engine Systems -> Engine Parts
Designed and written to serve the needs of the professional mechanic, do-it-yourself boat enthusiast, instructor and student, these manuals are based on actual teardowns done by Seloc’s editors/authors in our on-site facility. This repair manual covers all Yamaha outboard engines, 12-250 HP, 1-4 cylinder, V4, V6 models, 1990 to 2001. Every manual features: Easy-to-follow, step-by-step, illustrated procedures . Hundreds of exploded drawings, photographs and tables . Troubleshooting sections .
Part No: 1701
|
|
|
|
|
Home -> Engine Systems -> Engine Parts -> Engine Repair Manuals
SELOC Marine tune-up and repair manuals provide the most comprehensive, authoritative information available for outboard, inboard and stern-drive engines, as well as personal watercraft. SELOC has been the leading source of how-to information for the marine industry since 1974. Step-by-step illustrated keyed procedures guide you through every conceivable job possible, including all adjustments necessary. This manual covers Yamaha Outboard engines, all 2-stroke models, 2-250 HP, from 1997-2003.
Part No: 1703
|
|
|
|
Home -> Cabinet & Deck Hardware -> Hatches & Ports -> Hatch Accessories->Hatch Riser Arms
Replacement arms for Taylor hatches from 1987 to the present. Universal arms can be left or right.
Part No: 1722
|
|
|
|
Home -> Engine Systems -> Motor Mounts->Little & Junior Cranes
Precision engineered and fabricated from stainless steel, these removable cranes lift heavy loads with ease. Best of all, it takes just 20 seconds to set up or remove for storage. Optional spare mounting kits (VPN #176 & 196) include a set of brackets and rail clamps for an extra mounting location. Material: Polished stainless steel. Height: 60" mast height. Mounting Style: Horizontal or vertical mounting to railing. Included Equipment: Complete kit with mounts and 5/16" line.
Part No: 175
|
|
|
|
Home -> Engine Systems -> Engine Parts -> Electrical Eng Parts
Johnson/Evinrude No. s 386545, 386496, 379047 and 378238. Stainless steel and Delrin construction. 5 terminals with special waterproofing seal and drain holes. Brass chrome plated face nut, back-up nut and washer. Silvered contacts, stainless steel terminals and springs, brass screws. Mounting bushing 1-1/2" long.
Part No: 18-1801
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains
Sierra 18-2623 OMC Gear Housing Seal Kit.
Part No: 18-2623
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Exhaust Bellows
Seals the exhaust/water flow from the manifold to the exhaust outlet in the drive.
Part No: 18-2750
|
|
|
|
Home -> Engine Systems -> Engine Parts
Some larger V-8 engines that create a large amount of back pressure use exhaust tubes rather than bellows. This helps to relieve the excessive pressure and eliminate problems with premature bellows failure. In the past, the exhaust bellows would blow up like a balloon and cause the drive shaft bellows to rub against the yoke and U-joints causing holes in the bellows.
Part No: 18-2760
|
|
|
|
Home -> Engine Systems -> Engine Parts
Replacement for Mercruiser Inboard/Outboard #32-90949T .
Part No: 18-2761
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Shift Cable Bellows
Seals the shift cable as it passes through the transom.
Part No: 18-2763
|
|
|
|
|
Home -> Engine Systems -> Propellers & Drive Trains->Exhaust Bellows
Seals the exhaust/water flow from the manifold to the exhaust outlet in the drive.
Part No: 18-2764
|
|
|
