Roller Shaft Cap Nuts Only - 1/2", Pack of 8 from C E SMITH
Roller Size Length Shaft Diameter Shafts and Nuts 4" 5 1/4" 1/2" 4" 5 1/4" 5/8" 5" 6 1/4" 1/2" 5" 6 1/4" 5/8" 8" 9 1/4" 5/8" 10" 11 1/8" 5/8" 11" 12 3/4" 1/2" 12" 13 1/2" 5/8" Shaft Only 18" 19" 5/8" Cap Nuts Only Packs of 8.

Flex Trim - Black 1/2" opening from TACO PRODUCTS
For a beautiful finished look on unfinished edges. Just push it on and it's on to stay. Grips on difficult materials, compound curves, etc. Individual corrosion resistant aluminum clips for a permanent grip. Black or White . Sold in 25' lengths. . Available in four sizes:. 5/32" opening x 35/64"H. 1/4" opening x 1/2"H. 3/8" opening x 5/8"H.

Vertical Hand Pump Faucet, Chrome Over Brass from FYNSPRAY
Fynspray Vertical Hand Pump Faucet Vertical plunger pump with a gracefully arched spout. 50 strokes per gallon. Chrome over brass. 1"diameter tube . Fits 1/2"–5/8" hose .

Flush Lock and Latch from PERKO
Black plastic, with stainless steel "D" ring handle, stem and lock nut. Two O-rings for increased water resistance. Position indicator shows open or closed position. Lock with 2 keys. Door thickness: 3/8" to 1-1/4" . Face plate dimensions: 2-7/8" x 2-7/8" . Adjustment latch bar: 1-1/16" to 2-9/16" .

Rim Latch Sets - Reverse Bevel with Flush Strike from PERKO
Chrome-plated zinc. Sliding lock button. Case size: 2 1/8'' x 1 3/4''. Escutcheon Size: 4 3/8'' x 1 1/4''. For Door: 5/8'' to 1 3/8''.

Solid Brass Vertical Action Galley Pump from FYNSPRAY
Vertical plunger pump with a gracefully arched spout. 50 strokes per gallon. 1"diameter tube. Fits 1/2"–5/8" hose. Requires 8 1/2" clearance below counter surface; 9 3/4" above Material: Brass. Capacity: 50 strokes/gal. Dimensions: 9 3/4"H. Cutout Size: 1 1/8". Clearance: 8 1/2".

3/8" Bow/Stern Eye - 1.03" ID Between Studs x 4.63" Thread Length from SUNCOR
Bow / Stern Eye 304 Stainless Steel - Formed . Each U-Bolt set includes four nuts (two standard and two beveled) . Includes one bow plate, and one stern plate. . Threads are "UNC". . Stock size: 3/8" . ID between studs: 1. 03" . Thread length: 2. 50" .

Furler Kit for Boat Length to 16', 500lb. SWL, 1/8" Max. Wire dia., 1/4" Pin dia., 2-1/2" Pin-to-Pin, 5/32" Furling Line dia. from HARKEN
Furl or set your jib from your cockpit Harken small boat furlers allow the sail to be set and furled from the cockpit, a critical convenience in many racing dinghies and trailerable sailboats. Constructed of Hardkote anodized Teflon-impregnated aluminum, they feature multiple stacked races of Delrin or Torlon ball bearings for smooth rotation under load. The jib’s luff wire must be properly seized to the sail, since it carries most of the headstay load. 434 furler for dinghies under 16ft. (4.

Small Recessed Transom Shower from SHURFLO
Ideal for mounting to any horizontal surface. Kit includes spray nozzle, hose and necessary hardware for easy installation. White. Material: ABS plastic . Dimensions: 3-7/8"H x 3"W x 2-7/8"L . Port Sizes: 1/2" NPT . Clearance: 2-1/4" .

29mm Carbo Clew Block Assembly from HARKEN
From the folks who invented ball bearing blocks, this line of blocks boasts an excellent strength-to-weight ratio. 29mm doubles and triples feature a U-lock to hold the swivel in the front or side position, or allow it to spin freely. Use the 40mm blocks for jib and mainsheet systems on high-performance dinghies, and for high-load control lines on small keelboats. The 57mm blocks have an enormous working range that makes them ideal for main and jib sheets, spinnaker halyards and control lines.

Ignition Switch J/E W/Key from SIERRA
Johnson/Evinrude No. s 386545, 386496, 379047 and 378238. Stainless steel and Delrin construction. 5 terminals with special waterproofing seal and drain holes. Brass chrome plated face nut, back-up nut and washer. Silvered contacts, stainless steel terminals and springs, brass screws. Mounting bushing 1-1/2" long.

20 Amp Pushbutton Thermal Circuit Breaker from SIERRA
Very common pushbutton breakers for DC loads. Uses two-blade terminals. Mounts in 3/8" hole. Can be used with a waterproof boot over the button. Buttons are white. Switch Type: Pushbutton . Voltage Compatibility: DC . Safety Features: Waterproof boots available . Housing Material: Plastic . Housing Dimensions: 1. 75" x 1.

Sierra-Tube-Exhaust from SIERRA
Some larger V-8 engines that create a large amount of back pressure use exhaust tubes rather than bellows. This helps to relieve the excessive pressure and eliminate problems with premature bellows failure. In the past, the exhaust bellows would blow up like a balloon and cause the drive shaft bellows to rub against the yoke and U-joints causing holes in the bellows.

Prop Nut Kit, Yamaha 40-50HP from SIERRA
An excellent emergency item to carry in your toolbox, for those occasions when the prop nut is misplaced or lost.

Prop Nut Kit, Yamaha V4/V6 from SIERRA
An excellent emergency item to carry in your toolbox, for those occasions when the prop nut is misplaced or lost.