Micron® CF Antifouling Paint
Multi-season, self-smoothing, copper-free antifouling paint with Biolux® Slime Blocking Technology
Micron CF is a multi-season antifouling paint that instead of traditional copper, uses Econea and Biolux Slime Blocking Technology to keep hulls free of barnacles, zebra mussels and soft growth. Micron CF's copper-free formula helps to keep our boating waters clean, and also makes it a great choice for boats kept in marinas where copper-based antifouling paints are not allowed.
Like other paints in the Micron line, Micron CF wears away at a controlled rate and self-polishes as the boat is used, which reduces drag and helps to increase fuel efficiency. An additional benefit of this self-polishing technology is that less sanding is required when the time comes to repaint.
Micron CF can be applied to fiberglass, wood, steel and yes-on to aluminum hulls, since the copper-free formula will not cause galvanic corrosion. Micron CF is high in solids, VOC compliant and available in five crisp colors: Black, Blue, Red, Green and White.
Key Features
- Biolux Slime Blocking Technology
- Multi-season antifouling ablative for all fouling conditions
- Copper-free formula is better for the environment
- Self polishing formula reduces drag and paint build-up
- VOC compliant
- Available in five bright colors
- Biolux technology combats slime
Physical Data
- Type: Copper-free multi-season ablative
- Finish: Low Gloss
- Available colors: Blue, Green, Red, Black, White
- Components: 1
- Curing mechanism: Solvent Release
- Solids by Volume: 66%
- Coverage: 518sq. ft. /gal.
- VOC: 330 grams/liter (As Supplied)
- Active ingredients: 3.9% ECONEA
- Flash point: 98° F
Application
- Application Method: Brush, roller, airless, or conventional spray
- Number of coats recommended: 2 Coats, 3 on bare wood (first coat thinned)
- Wet Film Thickness: 3 mils
- Dry Film Thickness: 2 mils
- Applicator: High-quality short nap roller (maximum 3/8” nap) brush
- Application temperature Min. /Max. Range: Minimum 5°C/41°F and maximum 35°C/95°F.
- Thinner: 216, Model 117598 or 433, Model 203679
Drying Times* (Hours)
| Drying | @41°F | @50°F | @73°F | @95°F |
|---|---|---|---|---|
| To touch | 6 hr. | 3 hr. | 2 hr. | 1 hr. |
| To recoat | 12 hr. | 6 hr. | 4 hr. | 2 hr. |
| To launch | 18 hr. | 9 hr. | 6 hr. | 4 hr. |
*The above dry times are minimums. May be recorded after the minimum time shown. There is no maximum dry time before launching.
Get the right amount of paint:
| Boat Type | Bottom Paint |
|---|---|
| 10' Dinghy | 1 qt. |
| 14' Outboard | 1-2 qt. |
| 18' Runabout | 2 qt. |
| 20' Sailboat | 3 qt. |
| 24' Runabout | 3-4 qt. |
| 30' Sailboat | 1.5 gal. |
| 32' Cruiser | 1.5-2 gal. |
| 36' Auxiliary | 2 gal. |
| 40' Cruiser | 2.5 gal. |
| 45' Sailboat | 3-3.5 gal |
| 50' Sportfisher | 4+ gal. |
Another way to determine bottom paint quantity is to estimate the approximate surface area of the hull below the waterline, using the following formula:
Length x Beam x .75 = Approximate underwater surface area in square feet.
Each paint has a “theoretical coverage” area, but most paints require at least two coats, so you can expect actual coverage to be no greater than half of the theoretical value.
More information
For detailed application instructions and to view available colors, see the Micron CF Data Sheet. NOTE: Manufacturer data sheets are subject to revision. Linked data sheets are believed to be accurate at the time of publication.
